Temperature Controller - Staveb AG

More documents

Recommendations

Info

5-18 Parameter Functions and DefinitionsFigure 5.6Power ONOperationfunction groupkeyless than1 sec.Adjustmentfunction groupkey1 secondmin.key 3 seconds min.key The PV display flashes after one secondControl stopsInitial settingfunction groupkeyless than1 sec.Communicationssetup functiongroupControl in progressControl stoppedTo move from the Operation function group to the Initial Setting functiongroup, press key for 3 seconds or more.• The Initial Setting function group is not displayed whenInitial/Communications Protection is set to 2. This Initial Settingfunction group can be used when Initial Setting/CommunicationsProtection is set to 0 or 1.• The Scaling Upper Limit, Scaling Lower Limit, and Decimal Pointparameters are displayed when an analog input is selected as the inputtype.Publication 900-UM003C-EN-E - January 2004
Parameter Functions and Definitions 5-19Figure 5.7Initial setting function groupInput typeScaling upper limitScaling lower limitDecimal pointPage5-205-205-205-20°C/°F selectionSet point upper limit5-215-21Set point lower limitPID/ON/OFFStandard/heatingand coolingSTControl period (OUT1)Control period (OUT2)Direct/reverseoperationAlarm 1 typeMove to advancedsetting function group5-215-225-235-235-245-245-255-264-21Publication 900-UM003C-EN-E - January 2004
Page 7 and 8:
Table of Contentstoc-iiiExecuting t
Page 9 and 10:
Table of Contentstoc-vMemory Error
Page 11 and 12:
PrefaceSafety PrecautionsSafety Sig
Page 13 and 14:
Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16:
Bulletin 900-TC32 Input and Output
Page 17 and 18:
Bulletin 900-TC32 Input and Output
Page 19 and 20:
Chapter 2PreparationsHardware Insta
Page 21 and 22:
Preparations 2-3System Wiring and I
Page 23 and 24:
Preparations 2-5ATTENTION!• Clean
Page 25 and 26:
Preparations 2-7Removing and Attach
Page 27 and 28:
Preparations 2-9• Separate input
Page 29 and 30:
Preparations 2-11Wiring Control Out
Page 31 and 32:
Preparations 2-13Figure 2.12 Commun
Page 33 and 34:
Chapter 3Configuration and Basic Op
Page 35 and 36:
Configuration and Basic Operation 3
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52: Configuration and Basic Operation 3
Page 61 and 62: Chapter 4Parameter Adjustments and
Page 63 and 64: Parameter Adjustments and Applicati
Page 85 and 86: Chapter 5Parameter Functions and De
Page 87 and 88: Parameter Functions and Definitions
Page 101: Parameter Functions and Definitions
Page 127 and 128: Chapter 6Troubleshooting and Error
Page 129 and 130: Troubleshooting and Error Indicatio
Page 131 and 132: Appendix ASpecificationsFor the set
Page 133 and 134: A-3Sensor Input SettingRangesTable
Page 135 and 136: Appendix BParameter Operations List
Page 137 and 138: B-3Table B.C Initial Setting Functi
Page 139 and 140: B-5Figure B.1Power ONOperationfunct
Page 141 and 142: B-7Advanced setting function groupP
Page 143 and 144: Appendix CCalibrationParameter Stru
Page 145 and 146: Calibration C-3User CalibrationCali
Page 147 and 148: Calibration C-51. Connect the power
Page 149 and 150: Calibration C-713. Allow the count
Page 151 and 152: Calibration C-91. Connect the power
Page 153 and 154:
Calibration C-11Platinum Resistance
Page 155 and 156:
Appendix DGlossaryAdaptive Tuning:
Page 157 and 158:
Glossary D-3Deviation: A departure
Page 159 and 160:
Glossary D-5Loop Break Alarm: This
Page 161 and 162:
Glossary D-7Serial Communications:
Page 164 and 165:
Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

Create successful ePaper yourself

Delete template?

Save as template?