Temperature Controller - Staveb AG

More documents

Recommendations

Info

5-36 Parameter Functions and Definitionsbecomes the upper or lower limit MV value. Your configured MV limits willnot be exceeded by the controller.MV Upper LimitThe configurable ranges allowed during standard control and heating andcooling control are different.The manipulated variable at the control output 2 side during heating andcooling control is expressed as a negative value (see Table 5.AL).Table 5.AL MV Upper LimitControl Mode Configurable Range Units Default ValueStandard MV lower limit +0.1…105.0 % 105.0Heating and cooling 0.0…105.0 % 105.0MV Lower LimitThe configurable ranges allowed during standard control and heating andcooling control are different.The manipulated variable at the control output 2 side during heating andcooling control is expressed as a negative value (see Table 5.AM).Table 5.AM MV Lower LimitControl Mode Configurable Range Units Default ValueStandard –5.0 to MV upper limit –0.1 % –5.0Heating and cooling –105.0…+0.0 % –105.0Related Parameters• PID/ON/OFF (Initial Setting function group) (p. 5-22)• ST (Initial Setting function group) (p. 5-23)Input Digital FilterFunction: This parameter allows you to configure the time constant of thecontroller’s input digital filter. Figure 5.11 shows the effect on data afterpassing through the digital filter.Publication 900-UM003C-EN-E - January 2004
Parameter Functions and Definitions 5-37Figure 5.11PV before passing through filterAPV after passing through filter0.63ATimeconstantTimeInput digital filterTable 5.AN Input Digital FilterConfigurable Range Units Default Value0.0…999.9 Second 0.0Additional PV DisplayFunction: This parameter allows you to configure the controller so that onlythe PV is displayed. It is added to the top of the Operation function group. Itgives you the option of displaying the PV and SP (normal) or just the PV.Table 5.AOSelectionson: Displayedoff: Not displayedDefault SelectionoffManipulated Variable DisplayFunction: This parameter allows you to configure whether or not themanipulated variable is displayed.The manipulated variable is displayed when the Manipulated Variable Monitor(OUT1) parameters are set to ON, and not displayed when these parametersare set to OFF.Publication 900-UM003C-EN-E - January 2004
Page 7 and 8:
Table of Contentstoc-iiiExecuting t
Page 9 and 10:
Table of Contentstoc-vMemory Error
Page 11 and 12:
PrefaceSafety PrecautionsSafety Sig
Page 13 and 14:
Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16:
Bulletin 900-TC32 Input and Output
Page 17 and 18:
Bulletin 900-TC32 Input and Output
Page 19 and 20:
Chapter 2PreparationsHardware Insta
Page 21 and 22:
Preparations 2-3System Wiring and I
Page 23 and 24:
Preparations 2-5ATTENTION!• Clean
Page 25 and 26:
Preparations 2-7Removing and Attach
Page 27 and 28:
Preparations 2-9• Separate input
Page 29 and 30:
Preparations 2-11Wiring Control Out
Page 31 and 32:
Preparations 2-13Figure 2.12 Commun
Page 33 and 34:
Chapter 3Configuration and Basic Op
Page 35 and 36:
Configuration and Basic Operation 3
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Chapter 4Parameter Adjustments and
Page 63 and 64:
Parameter Adjustments and Applicati
Page 65 and 66:
Page 67 and 68:
Page 69 and 70: Parameter Adjustments and Applicati
Page 85 and 86: Chapter 5Parameter Functions and De
Page 87 and 88: Parameter Functions and Definitions
Page 119: Parameter Functions and Definitions
Page 127 and 128: Chapter 6Troubleshooting and Error
Page 129 and 130: Troubleshooting and Error Indicatio
Page 131 and 132: Appendix ASpecificationsFor the set
Page 133 and 134: A-3Sensor Input SettingRangesTable
Page 135 and 136: Appendix BParameter Operations List
Page 137 and 138: B-3Table B.C Initial Setting Functi
Page 139 and 140: B-5Figure B.1Power ONOperationfunct
Page 141 and 142: B-7Advanced setting function groupP
Page 143 and 144: Appendix CCalibrationParameter Stru
Page 145 and 146: Calibration C-3User CalibrationCali
Page 147 and 148: Calibration C-51. Connect the power
Page 149 and 150: Calibration C-713. Allow the count
Page 151 and 152: Calibration C-91. Connect the power
Page 153 and 154: Calibration C-11Platinum Resistance
Page 155 and 156: Appendix DGlossaryAdaptive Tuning:
Page 157 and 158: Glossary D-3Deviation: A departure
Page 159 and 160: Glossary D-5Loop Break Alarm: This
Page 161 and 162: Glossary D-7Serial Communications:
Page 164 and 165: Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

Create successful ePaper yourself

Delete template?

Save as template?