Temperature Controller - Staveb AG

More documents

Recommendations

Info

B-2Table B.C Initial Setting Function GroupParameter Name Symbol Setting (Monitor) Value Display Default Unit SetValueInput Type cn-t PlatinumresistancethermometerThermocoupleNon-contacttemperaturesensorAnalog input0: Pt1001: Pt1002: Pt1000: K1: K2: J3: J4: T17: T5: E12: K10…70°C13: K60…120°C3: JPt1004: JPt1006: L7: U18: U8: N9: R10: S11: B14: K115…165°C15: K160…260°C16: 0…50 mAScaling Upper Limit in-h Scaling lower limit +1…9999 NoneScaling Lower Limit in-l –1999 to scaling upper limit –1 NoneDecimal Point dp 0,1 None<strong>Temperature</strong> Unit d-u °C, °F c, f NoneSet Point Upper Limit sl-h SP lower limit +1 to input range lower value(temperature)SP lower limit +1 to scaling upper limit (analog)Set Point Lower Limit sl-l Input range lower limit to SP upper limit –1(temperature)Scaling lower limit to SP upper limit –1 (analog)PID/ON/OFF cntl 2-PID, ON/OFF pid,onofStandard/Heating andCoolings-hc Standard, heating and cooling stnd,h-cON/OFFStandardST st ON, OFF on, off ONControl Period (OUT1) cp 1…99 SecondControl Period (OUT2) c-cp 1…99 SecondNoneNoneEUEUEUEUPublication 900-UM003C-EN-E - January 2004
B-3Table B.C Initial Setting Function Group (Continued)Parameter Name Symbol Setting (Monitor) Value Display Default Unit SetValueDirect/ReverseOperationorev Direct operation, reverse operation or-d,or-rAlarm 1 Type alt1 0: Alarm function OFF1: Upper- and lower-limit (deviation range)2: Upper-limit (deviation)3: Lower-limit (deviation)4: Upper- and lower-limit range (deviation range)5: Upper- and lower-limit alarm with standby sequence(deviation range)6: Upper-limit alarm with standby sequence (deviation)7: Lower-limit alarm with standby sequence (deviation)8: Upper-limit (absolute-value)9: Lower-limit (absolute-value)10: Upper-limit with standby sequence(absolute-value)11: Lower-limit with standby sequence(absolute-value)Move to AdvancedSetting FunctionGroupReverseoperationNoneamov –1999…+9999 NoneTable B.D Advanced Setting Function GroupParameter Name Symbol Setting (Monitor) Value Display Default Unit Set ValueParameter Initialize init ON, OFF on, off OFF NoneMulti-SP Uses mspu ON, OFF on, off OFF NoneSP Ramp Set Value sprt OFF, 1…9999 off, 1 to 9999 OFF EUStandby Sequence Reset rest Condition A, Condition B a, b Condition A NoneMethodAlarm 1 Open in Alarm al1n Open in alarm/Close in alarm n-o, n-c Close in alarm NoneAlarm 1 Hysteresis alh1 0.1…999.9 0.2 EUST Stable Range st-b 0.1…999.9 15.0 °C or °Fα (Alpha) alfa 0.00…1.00 0.65 NoneMV Upper Limit ol-h MV lower limit +0.1…105.0105.0 %(standard)0.0…105.0 (heating and cooling) 105.0 %MV Lower Limit ol-l –5.0 to MV upper limit –0.1–5.0 %(standard)–105.0…0.0 (heating and cooling) –105.0 %Input Digital Filter inf 0.1…999.9 0.0 SecondAdditional PV Display puad ON, OFF on, off OFF NonePublication 900-UM003C-EN-E - January 2004
Page 7 and 8:
Table of Contentstoc-iiiExecuting t
Page 9 and 10:
Table of Contentstoc-vMemory Error
Page 11 and 12:
PrefaceSafety PrecautionsSafety Sig
Page 13 and 14:
Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16:
Bulletin 900-TC32 Input and Output
Page 17 and 18:
Bulletin 900-TC32 Input and Output
Page 19 and 20:
Chapter 2PreparationsHardware Insta
Page 21 and 22:
Preparations 2-3System Wiring and I
Page 23 and 24:
Preparations 2-5ATTENTION!• Clean
Page 25 and 26:
Preparations 2-7Removing and Attach
Page 27 and 28:
Preparations 2-9• Separate input
Page 29 and 30:
Preparations 2-11Wiring Control Out
Page 31 and 32:
Preparations 2-13Figure 2.12 Commun
Page 33 and 34:
Chapter 3Configuration and Basic Op
Page 35 and 36:
Configuration and Basic Operation 3
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Chapter 4Parameter Adjustments and
Page 63 and 64:
Parameter Adjustments and Applicati
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86: Chapter 5Parameter Functions and De
Page 87 and 88: Parameter Functions and Definitions
Page 127 and 128: Chapter 6Troubleshooting and Error
Page 129 and 130: Troubleshooting and Error Indicatio
Page 131 and 132: Appendix ASpecificationsFor the set
Page 133 and 134: A-3Sensor Input SettingRangesTable
Page 135: Appendix BParameter Operations List
Page 139 and 140: B-5Figure B.1Power ONOperationfunct
Page 141 and 142: B-7Advanced setting function groupP
Page 143 and 144: Appendix CCalibrationParameter Stru
Page 145 and 146: Calibration C-3User CalibrationCali
Page 147 and 148: Calibration C-51. Connect the power
Page 149 and 150: Calibration C-713. Allow the count
Page 151 and 152: Calibration C-91. Connect the power
Page 153 and 154: Calibration C-11Platinum Resistance
Page 155 and 156: Appendix DGlossaryAdaptive Tuning:
Page 157 and 158: Glossary D-3Deviation: A departure
Page 159 and 160: Glossary D-5Loop Break Alarm: This
Page 161 and 162: Glossary D-7Serial Communications:
Page 164 and 165: Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?