Temperature Controller - Staveb AG

More documents

Recommendations

Info

B-6Operation function groupPVPV/SPMulti-SPFigure B.2Add in the“additional PVdisplay”parameter.Adjustment function groupAT execute/cancelAuto-tuningCommunications writingEnable or disable writing bycommunications.Set point 0Set point during SP rampRun/stopSet point 1Set point 2Set pointsused bymulti-SPAlarm value 1Set point 3Upper-limit alarm value 1Set eitherof theseparameters.<strong>Temperature</strong> input shift1-point shiftLower-limit alarm value 1Upper-limit temperatureinput shift valueMV monitor (OUT1)Lower-limit temperatureinput shift value2-point shiftMV monitor (OUT2)Proportional bandPInitial setting function groupInput typeIntegral timeDerivative timeIDPIDsettingsScaling upper limit0…50 mVScaling lower limitManual reset valueClear the offset duringstabilization of P or PD control.Hysteresis (OUT1)Decimal pointNumber of digits displayedpast decimal point°C/°F selectionLimit the set point.Set point upper limitSet point lower limitPID/ON/OFFSelect the control system.Hysteresis (OUT2)Control period (heat)Set the pulse output cycle.Direct/reverse operationControl the manipulated variable accordingto the increase/decrease in the PV.Alarm 1 typeSelect the alarm mode.STSelf-tuningMove to advancedsetting function groupPublication 900-UM003C-EN-E - January 2004
B-7Advanced setting function groupParameter initializeFigure B.2 (Continued)αAdvanced PID parameterMulti-SP usesSP ramp set valueMV upper limitMV lower limitLimited to MVcalculation valueStandby sequence reset methodReset conditions after standby sequenceis canceled.Alarm 1 open in alarmSet the alarm output 1 ON/OFF states.Alarm 1 hysteresisInput digital filterSet the time constant in seconds.Additional PV displayDisplayed first in the operation function group.Manipulated variable displayST stable rangeSet the deviation.Automatic return of display modeAutomatic return to operation function groupwhen the keys on the front panel are operated.Move to calibrationfunction groupAlarm 1 latchProtect function groupOperation/adjustment protectionRestricts display and modification of menusin the operation and adjustment function groupsInitial setting communications protectionRestricts display and modification of menusin the initial setup, operation level and adjustmentfunction groups.Setting change protectionProtects changes to setups by operationof the front panel keys.Protect function groupmove timeOutput/input errorCold junction compensating methodMB command logic switchingCommunications setting function groupCommunicationUnit No.Baud rateData bitStop bitParityCommunication setup on other partypersonal computer is different.Publication 900-UM003C-EN-E - January 2004
Page 7 and 8:
Table of Contentstoc-iiiExecuting t
Page 9 and 10:
Table of Contentstoc-vMemory Error
Page 11 and 12:
PrefaceSafety PrecautionsSafety Sig
Page 13 and 14:
Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16:
Bulletin 900-TC32 Input and Output
Page 17 and 18:
Bulletin 900-TC32 Input and Output
Page 19 and 20:
Chapter 2PreparationsHardware Insta
Page 21 and 22:
Preparations 2-3System Wiring and I
Page 23 and 24:
Preparations 2-5ATTENTION!• Clean
Page 25 and 26:
Preparations 2-7Removing and Attach
Page 27 and 28:
Preparations 2-9• Separate input
Page 29 and 30:
Preparations 2-11Wiring Control Out
Page 31 and 32:
Preparations 2-13Figure 2.12 Commun
Page 33 and 34:
Chapter 3Configuration and Basic Op
Page 35 and 36:
Configuration and Basic Operation 3
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Chapter 4Parameter Adjustments and
Page 63 and 64:
Parameter Adjustments and Applicati
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Chapter 5Parameter Functions and De
Page 87 and 88:
Parameter Functions and Definitions
Page 89 and 90: Parameter Functions and Definitions
Page 127 and 128: Chapter 6Troubleshooting and Error
Page 129 and 130: Troubleshooting and Error Indicatio
Page 131 and 132: Appendix ASpecificationsFor the set
Page 133 and 134: A-3Sensor Input SettingRangesTable
Page 135 and 136: Appendix BParameter Operations List
Page 137 and 138: B-3Table B.C Initial Setting Functi
Page 139: B-5Figure B.1Power ONOperationfunct
Page 143 and 144: Appendix CCalibrationParameter Stru
Page 145 and 146: Calibration C-3User CalibrationCali
Page 147 and 148: Calibration C-51. Connect the power
Page 149 and 150: Calibration C-713. Allow the count
Page 151 and 152: Calibration C-91. Connect the power
Page 153 and 154: Calibration C-11Platinum Resistance
Page 155 and 156: Appendix DGlossaryAdaptive Tuning:
Page 157 and 158: Glossary D-3Deviation: A departure
Page 159 and 160: Glossary D-5Loop Break Alarm: This
Page 161 and 162: Glossary D-7Serial Communications:
Page 164 and 165: Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

Create successful ePaper yourself

Delete template?

Save as template?