Temperature Controller - Staveb AG

More documents

Recommendations

Info

6-2 Troubleshooting and Error Indication• When output input error (Advanced Setting function group) is set toON, the alarm 1 output turns ON when an input error occurs.• An error message is displayed when process value or PV/SP aredisplayed.Figure 6.1RTD input(setting range: without -199.9…500.0 (°C) type)Themocuple input(setting range: without -199.9…400.0 (°C) type)S. Err indication Displayed by numerical value S. Err indicationInput indication range-1999display range9999(-199.9)(999.9)Analog inputdisplay range < Displayed by numerical valueS. Err indication cccc indication Displayed by numerical value cccc indication S. Err indication-1999(-199.9)displayrange9999(999.9)Input indication rangeAnalog inputdisplay range > Displayed by numerical valueS. Err indication Displayed by numerical value S. Err indicationInput indication range-1999display range9999(-199.9)(999.9)RTD input(setting range: -199.9…500.0 (°C) type)Themocuple input(setting range: without -199.9…400.0 (°C) type)cccc indication Displayed by numerical value S. Err indicationInput indication range-1999 display range 9999(-199.9)(999.9)Memory ErrorMeaningInternal memory operation is in error.ActionFirst, turn the power OFF then back ON again. If the display remains thesame, the Bulletin 900-TC32 must be repaired. If the display is restored, then aprobable cause can be electrical noise affecting the control system. Check forelectrical noise.Operation at ErrorControl output and alarm output turn OFF.Publication 900-UM003C-EN-E - January 2004
Troubleshooting and Error Indication 6-3MeaningDisplay Over RangeThough this is not an error, this is displayed when the process value exceedsthe display range when the control range is larger than the display range(–1999…+9999).• When less than –1999:• When more than 9999:ActionControl continues, allowing normal operation. An error message is displayedwhen process value or PV/SP are displayed.Publication 900-UM003C-EN-E - January 2004
Page 7 and 8:
Table of Contentstoc-iiiExecuting t
Page 9 and 10:
Table of Contentstoc-vMemory Error
Page 11 and 12:
PrefaceSafety PrecautionsSafety Sig
Page 13 and 14:
Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16:
Bulletin 900-TC32 Input and Output
Page 17 and 18:
Bulletin 900-TC32 Input and Output
Page 19 and 20:
Chapter 2PreparationsHardware Insta
Page 21 and 22:
Preparations 2-3System Wiring and I
Page 23 and 24:
Preparations 2-5ATTENTION!• Clean
Page 25 and 26:
Preparations 2-7Removing and Attach
Page 27 and 28:
Preparations 2-9• Separate input
Page 29 and 30:
Preparations 2-11Wiring Control Out
Page 31 and 32:
Preparations 2-13Figure 2.12 Commun
Page 33 and 34:
Chapter 3Configuration and Basic Op
Page 35 and 36:
Configuration and Basic Operation 3
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Chapter 4Parameter Adjustments and
Page 63 and 64:
Parameter Adjustments and Applicati
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78: Parameter Adjustments and Applicati
Page 85 and 86: Chapter 5Parameter Functions and De
Page 87 and 88: Parameter Functions and Definitions
Page 127: Chapter 6Troubleshooting and Error
Page 131 and 132: Appendix ASpecificationsFor the set
Page 133 and 134: A-3Sensor Input SettingRangesTable
Page 135 and 136: Appendix BParameter Operations List
Page 137 and 138: B-3Table B.C Initial Setting Functi
Page 139 and 140: B-5Figure B.1Power ONOperationfunct
Page 141 and 142: B-7Advanced setting function groupP
Page 143 and 144: Appendix CCalibrationParameter Stru
Page 145 and 146: Calibration C-3User CalibrationCali
Page 147 and 148: Calibration C-51. Connect the power
Page 149 and 150: Calibration C-713. Allow the count
Page 151 and 152: Calibration C-91. Connect the power
Page 153 and 154: Calibration C-11Platinum Resistance
Page 155 and 156: Appendix DGlossaryAdaptive Tuning:
Page 157 and 158: Glossary D-3Deviation: A departure
Page 159 and 160: Glossary D-5Loop Break Alarm: This
Page 161 and 162: Glossary D-7Serial Communications:
Page 164 and 165: Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

Create successful ePaper yourself

Delete template?

Save as template?