Temperature Controller - Staveb AG

More documents

Recommendations

Info

3-6 Configuration and Basic OperationCommunications FunctionThe Bulletin 900-TC32 can be provided with a communications function thatallows you to check and set controller parameters from a personal computer(PC) that has 900Builder software installed. If the communications function isrequired, a controller that has this function must be ordered. See Table 1.A.Follow the procedure below to move to the Communications Setting functiongroup.1. Press the key for at least 3 seconds in the Operation function group.The function group moves to the Initial Setting function group.2. Press the key for less than 1 second. The Initial Setting functiongroup moves to the Communications Setting function group.3. Pressing the M key advances the parameters as shown in the followingfigure.4. Press the U or D key to change the parameter setups.Figure 3.4Communications unit No.Baud rateData bitStop bitParitySetting up Communications Parameter DataSet the Bulletin 900-TC32 communication parameter specifications so thatthey match the communication parameter setup for the personal computerusing 900Builder software. In a multidrop (RS-485) 1:N configuration, matchthe setting data except the communications unit numbers on all units. Uniquecommunications unit numbers must be configured for each controller/devicein an RS-485 system.Publication 900-UM003C-EN-E - January 2004
Configuration and Basic Operation 3-7Table 3.BParameterDisplayedCharactersConfigurable(Monitor) ValueDefaultUnitsCommunications Unit No. u-no 0…99 1 NoneBaud Rate bps 1.2, 2.4, 4.8, 9.6, 19.2 9.6 kbpsData Bit len 7, 8 7 bitStop Bit sbit 1, 2 2 bitParity prty None, even, odd Even NoneInitial Setup Examples The and M keys are used to switch between configuration menus, and theamount of time that you hold the keys down for determines whichconfiguration menu you move to. This section describes two typical examples.Publication 900-UM003C-EN-E - January 2004
Page 7 and 8: Table of Contentstoc-iiiExecuting t
Page 9 and 10: Table of Contentstoc-vMemory Error
Page 11 and 12: PrefaceSafety PrecautionsSafety Sig
Page 13 and 14: Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16: Bulletin 900-TC32 Input and Output
Page 17 and 18: Bulletin 900-TC32 Input and Output
Page 19 and 20: Chapter 2PreparationsHardware Insta
Page 21 and 22: Preparations 2-3System Wiring and I
Page 23 and 24: Preparations 2-5ATTENTION!• Clean
Page 25 and 26: Preparations 2-7Removing and Attach
Page 27 and 28: Preparations 2-9• Separate input
Page 29 and 30: Preparations 2-11Wiring Control Out
Page 31 and 32: Preparations 2-13Figure 2.12 Commun
Page 33 and 34: Chapter 3Configuration and Basic Op
Page 35 and 36: Configuration and Basic Operation 3
Page 37: Configuration and Basic Operation 3
Page 61 and 62: Chapter 4Parameter Adjustments and
Page 63 and 64: Parameter Adjustments and Applicati
Page 85 and 86: Chapter 5Parameter Functions and De
Page 87 and 88: Parameter Functions and Definitions
Page 89 and 90:
Parameter Functions and Definitions
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Chapter 6Troubleshooting and Error
Page 129 and 130:
Troubleshooting and Error Indicatio
Page 131 and 132:
Appendix ASpecificationsFor the set
Page 133 and 134:
A-3Sensor Input SettingRangesTable
Page 135 and 136:
Appendix BParameter Operations List
Page 137 and 138:
B-3Table B.C Initial Setting Functi
Page 139 and 140:
B-5Figure B.1Power ONOperationfunct
Page 141 and 142:
B-7Advanced setting function groupP
Page 143 and 144:
Appendix CCalibrationParameter Stru
Page 145 and 146:
Calibration C-3User CalibrationCali
Page 147 and 148:
Calibration C-51. Connect the power
Page 149 and 150:
Calibration C-713. Allow the count
Page 151 and 152:
Calibration C-91. Connect the power
Page 153 and 154:
Calibration C-11Platinum Resistance
Page 155 and 156:
Appendix DGlossaryAdaptive Tuning:
Page 157 and 158:
Glossary D-3Deviation: A departure
Page 159 and 160:
Glossary D-5Loop Break Alarm: This
Page 161 and 162:
Glossary D-7Serial Communications:
Page 164 and 165:
Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?