Temperature Controller - Staveb AG

More documents

Recommendations

Info

A-4The applicable standards for each of the above input ranges are as follows:• K, J, T, E, N, R, S, B: JIS C1602-1995, IEC 584-1• L: Fe-CuNi, DIN 43710-1985• U: Cu-CuNi, DIN 43710-1985• JPt100: JIS C 1604-1989, JIS C 1606-1989• Pt100: JIS C 1604-1997 IEC 751Note: The default is set value 0.Control Range• Platinum resistance thermometer and thermocouple input:• –20°C of temperature setting lower limit to +20°C of thetemperature setting upper limit, or• –40°F of temperature setting lower limit to +40°F of the temperaturesetting upper limit• Non-contact input: Same as input indication range• Analog input: –5%…+105% of scaling rangePublication 900-UM003C-EN-E - January 2004
Appendix BParameter Operations ListTable B.A Operation Function GroupParameter Name Symbol Setting (Monitor) Value Display Default Unit Set ValuePV Sensor input indication range EUPV/SP SP lower limit to SP upper limit 0 EUMulti-SP m-sp 0…3 0 NoneSet Point during SP Ramp sp-m SP lower limit to SP upper limit EURUN/STOP r-s RUN/STOP run, stop RUN NoneAlarm Value 1 al-1 –1999…+9999 0 EUUpper-Limit Alarm Value 1 al1h –1999…+9999 0 EULower-Limit Alarm Value 1 al1l –1999…+9999 0 EUMV Monitor (OUT1) o 0.0…+100.0 (standard) %0.0…100.0 (heating and cooling) %MV Monitor (OUT2) c-o 0.0…100.0 %Table B.B Adjustment Function GroupParameter Name Symbol Setting (Monitor) Value Display Default Unit Set ValueAT Execute/Cancel at ON, OFF on, off off NoneCommunications Writing cmyt ON, OFF on, off off NoneSet Point 0 sp-0 SP lower limit to upper limit 0 EUSet Point 1 sp-1 SP lower limit to upper limit 0 EUSet Point 2 sp-2 SP lower limit to upper limit 0 EUSet Point 3 sp-3 SP lower limit to upper limit 0 EUTemperature Input Shift ins –199.9…+999.9 0.0 °C or °FUpper-Limit Temperature Input insh –199.9…+999.9 0.0 °C or °FShift ValueLower-Limit Temperature Input insl –199.9…+999.9 0.0 °C or °FShift ValueProportional Band p 0.1…999.9 8.0 EUIntegral Time i 0…3999 233 SecondDerivative Time d 0…3999 40 SecondCooling Coefficient c-sc 0.01…99.99 1.00 NoneDead Band c-db –199.9…999.9 0.1 EUManual Reset Value of-r 0.0…100.0 50.0 %Hysteresis (OUT1) hys 0.1…999.9 1.0 EUHysteresis (OUT2) chys 0.1…999.9 1.0 EUB-1 Publication 900-UM003C-EN-E - January 2004
Page 7 and 8:
Table of Contentstoc-iiiExecuting t
Page 9 and 10:
Table of Contentstoc-vMemory Error
Page 11 and 12:
PrefaceSafety PrecautionsSafety Sig
Page 13 and 14:
Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16:
Bulletin 900-TC32 Input and Output
Page 17 and 18:
Bulletin 900-TC32 Input and Output
Page 19 and 20:
Chapter 2PreparationsHardware Insta
Page 21 and 22:
Preparations 2-3System Wiring and I
Page 23 and 24:
Preparations 2-5ATTENTION!• Clean
Page 25 and 26:
Preparations 2-7Removing and Attach
Page 27 and 28:
Preparations 2-9• Separate input
Page 29 and 30:
Preparations 2-11Wiring Control Out
Page 31 and 32:
Preparations 2-13Figure 2.12 Commun
Page 33 and 34:
Chapter 3Configuration and Basic Op
Page 35 and 36:
Configuration and Basic Operation 3
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Chapter 4Parameter Adjustments and
Page 63 and 64:
Parameter Adjustments and Applicati
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84: Parameter Adjustments and Applicati
Page 85 and 86: Chapter 5Parameter Functions and De
Page 87 and 88: Parameter Functions and Definitions
Page 127 and 128: Chapter 6Troubleshooting and Error
Page 129 and 130: Troubleshooting and Error Indicatio
Page 131 and 132: Appendix ASpecificationsFor the set
Page 133: A-3Sensor Input SettingRangesTable
Page 137 and 138: B-3Table B.C Initial Setting Functi
Page 139 and 140: B-5Figure B.1Power ONOperationfunct
Page 141 and 142: B-7Advanced setting function groupP
Page 143 and 144: Appendix CCalibrationParameter Stru
Page 145 and 146: Calibration C-3User CalibrationCali
Page 147 and 148: Calibration C-51. Connect the power
Page 149 and 150: Calibration C-713. Allow the count
Page 151 and 152: Calibration C-91. Connect the power
Page 153 and 154: Calibration C-11Platinum Resistance
Page 155 and 156: Appendix DGlossaryAdaptive Tuning:
Page 157 and 158: Glossary D-3Deviation: A departure
Page 159 and 160: Glossary D-5Loop Break Alarm: This
Page 161 and 162: Glossary D-7Serial Communications:
Page 164 and 165: Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

Create successful ePaper yourself

Delete template?

Save as template?