Temperature Controller - Staveb AG

More documents

Recommendations

Info

2-2 PreparationsPanel CutoutDimensions are in millimeters. Dimensions are not intended to be used formanufacturing purposes.Note: To convert millimeters to inches, multiply by 0.0394.60 min.Figure 2.2(48 x number of units -2.5) ➌2240 min.45 ➊Horizontal Group Mounting of Controllers(without Waterproofing) ➍22➋➋Individual Mounting (Vertical and Horizontal)➊➋➌➍Tolerance: +0.6…0.0 mmTolerance: +0.3…0.0 mmTolerance: +1.0…0.0 mmWaterproofing is not possible when ground-mounting several units.• The recommended panel thickness is 1…5 mm.• Maintain the specified mounting space between each controller.Controllers must not be group mounted vertically.• When two or more Bulletin 900-TC32s are mounted, make sure that thesurrounding temperature does not exceed the allowable operatingtemperature given in the specifications. Consider a cooling fan if thetemperature may exceed limits.Note: The protective structure of this controller conforms to the followingstandards Parts that are not indicated as being protected or that are indicatedas IP_0 are not waterproof.• Front panel: NEMA 4X for indoor use (equivalent to IP66)• Rear case: IP20• Terminals: IP00Publication 900-UM003C-EN-E - January 2004
Preparations 2-3System Wiring and Installation GuidelinesATTENTION!Risk of Electrical Shock• Devices are Open Type, Listed Process ControlEquipment and must be mounted in an enclosure.• More than one disconnect switch may be required tode-energize the equipment before servicing.• Signal inputs are SELV, limited energy.• To reduce risk of fire or electrical shock, do notinterconnect the outputs of different Class 2 circuits.• Disconnect all power (including field devices) beforeinstalling and/or servicing.ATTENTION!• Do not touch the controller’s wiring terminalswhile the power is ON. Doing so may cause anelectric shock.• Do not allow metal fragments or lead wire scrapsto fall inside the Bulletin 900-TC32 TemperatureController. These may cause electric shock, fire,or malfunction.• Never disassemble, repair, or modify theBulletin 900-TC32 Temperature Controller withline or field device power applied. Doing so maycause electric shock, fire, or malfunction.• Do not use the Bulletin 900-TC32 TemperatureController in flammable and explosive gasatmospheres.• Use the Bulletin 900-TC32 Temperature Controlleroutputs within the rated load. Not doing so may causedamage or fire.Publication 900-UM003C-EN-E - January 2004
Page 7 and 8: Table of Contentstoc-iiiExecuting t
Page 9 and 10: Table of Contentstoc-vMemory Error
Page 11 and 12: PrefaceSafety PrecautionsSafety Sig
Page 13 and 14: Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16: Bulletin 900-TC32 Input and Output
Page 17 and 18: Bulletin 900-TC32 Input and Output
Page 19: Chapter 2PreparationsHardware Insta
Page 23 and 24: Preparations 2-5ATTENTION!• Clean
Page 25 and 26: Preparations 2-7Removing and Attach
Page 27 and 28: Preparations 2-9• Separate input
Page 29 and 30: Preparations 2-11Wiring Control Out
Page 31 and 32: Preparations 2-13Figure 2.12 Commun
Page 33 and 34: Chapter 3Configuration and Basic Op
Page 35 and 36: Configuration and Basic Operation 3
Page 61 and 62: Chapter 4Parameter Adjustments and
Page 63 and 64: Parameter Adjustments and Applicati
Page 71 and 72:
Parameter Adjustments and Applicati
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Chapter 5Parameter Functions and De
Page 87 and 88:
Parameter Functions and Definitions
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Chapter 6Troubleshooting and Error
Page 129 and 130:
Troubleshooting and Error Indicatio
Page 131 and 132:
Appendix ASpecificationsFor the set
Page 133 and 134:
A-3Sensor Input SettingRangesTable
Page 135 and 136:
Appendix BParameter Operations List
Page 137 and 138:
B-3Table B.C Initial Setting Functi
Page 139 and 140:
B-5Figure B.1Power ONOperationfunct
Page 141 and 142:
B-7Advanced setting function groupP
Page 143 and 144:
Appendix CCalibrationParameter Stru
Page 145 and 146:
Calibration C-3User CalibrationCali
Page 147 and 148:
Calibration C-51. Connect the power
Page 149 and 150:
Calibration C-713. Allow the count
Page 151 and 152:
Calibration C-91. Connect the power
Page 153 and 154:
Calibration C-11Platinum Resistance
Page 155 and 156:
Appendix DGlossaryAdaptive Tuning:
Page 157 and 158:
Glossary D-3Deviation: A departure
Page 159 and 160:
Glossary D-5Loop Break Alarm: This
Page 161 and 162:
Glossary D-7Serial Communications:
Page 164 and 165:
Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

Create successful ePaper yourself

Delete template?

Save as template?