Temperature Controller - Staveb AG

More documents

Recommendations

Info

5-20 Parameter Functions and DefinitionsInput TypeFunction: This parameter allows you to configure the sensor type by enteringa corresponding code (set value).If the Input Type parameter is changed (Set Value modified), the set pointlimits are changed to the defaults of the newly selected sensor. If the set pointlimits must be changed, you can configure the Set Point Upper Limit and SetPoint Lower Limit parameters (Initial Setting function group).Configure the code (Set Value) according to Table A.B, List of Input Types. Thedefaults are as follows:• Platinum resistance thermometer: 0: platinum resistance thermometerPt100 (requires a specific controller cat. no.; see Table 1.A)• Thermocouple: 0: K thermocouple (requires a specific controller cat.no.; see Table 1.A)Related Parameters°C/°F Selection (p. 5-21), Set Point Upper Limit, Set Point Lower Limit(p. 5-21) (Initial Setting function group)Scaling Upper Limit,Scaling Lower Limit,Decimal PointConditions of Use: The input type must be set to analog input.Function: When voltage input is selected as the input type, scaling to otherengineering units (EU) is possible. Set the upper limit in the Scaling UpperLimit parameter and the lower limit in the Scaling Lower Limit parameter.The Decimal Point parameter specifies the decimal point position of thesystem parameters (Set Point, etc.) whose unit is set to EU.Publication 900-UM003C-EN-E - January 2004
Parameter Functions and Definitions 5-21Table 5.T Scaling Upper Limit, Scaling Lower LimitParameter Configurable Range Units Default ValueScaling Upper Limit Scaling lower limit +1…9999 None 100Scaling Lower Limit –1999 to scaling upper limit –1 None 0Table 5.U Decimal Point: Default is 0: 0 Digits Past Decimal PointSet Value Meaning Example0 0 digits past decimal point 12341 1 digit past decimal point 123.4Related ParameterInput Type (Initial Setting function group) (p. 5-20)°C/°F SelectionConditions of Use: The input type must be configured for a temperatureinput.Function: This parameter allows you to configure the temperature input unitsto either of °C or °F.Table 5.VSelectionsc: °Cf: °FDefault UnitscRelated ParameterInput Type (Initial Setting function group) (p. 5-20)Set Point Upper Limit,Set Point Lower LimitFunction: These parameters allow you to configure the maximum allowablerange for an operator to enter the set point value. The SP can be configuredPublication 900-UM003C-EN-E - January 2004
Page 7 and 8:
Table of Contentstoc-iiiExecuting t
Page 9 and 10:
Table of Contentstoc-vMemory Error
Page 11 and 12:
PrefaceSafety PrecautionsSafety Sig
Page 13 and 14:
Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16:
Bulletin 900-TC32 Input and Output
Page 17 and 18:
Bulletin 900-TC32 Input and Output
Page 19 and 20:
Chapter 2PreparationsHardware Insta
Page 21 and 22:
Preparations 2-3System Wiring and I
Page 23 and 24:
Preparations 2-5ATTENTION!• Clean
Page 25 and 26:
Preparations 2-7Removing and Attach
Page 27 and 28:
Preparations 2-9• Separate input
Page 29 and 30:
Preparations 2-11Wiring Control Out
Page 31 and 32:
Preparations 2-13Figure 2.12 Commun
Page 33 and 34:
Chapter 3Configuration and Basic Op
Page 35 and 36:
Configuration and Basic Operation 3
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54: Configuration and Basic Operation 3
Page 61 and 62: Chapter 4Parameter Adjustments and
Page 63 and 64: Parameter Adjustments and Applicati
Page 85 and 86: Chapter 5Parameter Functions and De
Page 87 and 88: Parameter Functions and Definitions
Page 103: Parameter Functions and Definitions
Page 127 and 128: Chapter 6Troubleshooting and Error
Page 129 and 130: Troubleshooting and Error Indicatio
Page 131 and 132: Appendix ASpecificationsFor the set
Page 133 and 134: A-3Sensor Input SettingRangesTable
Page 135 and 136: Appendix BParameter Operations List
Page 137 and 138: B-3Table B.C Initial Setting Functi
Page 139 and 140: B-5Figure B.1Power ONOperationfunct
Page 141 and 142: B-7Advanced setting function groupP
Page 143 and 144: Appendix CCalibrationParameter Stru
Page 145 and 146: Calibration C-3User CalibrationCali
Page 147 and 148: Calibration C-51. Connect the power
Page 149 and 150: Calibration C-713. Allow the count
Page 151 and 152: Calibration C-91. Connect the power
Page 153 and 154: Calibration C-11Platinum Resistance
Page 155 and 156:
Appendix DGlossaryAdaptive Tuning:
Page 157 and 158:
Glossary D-3Deviation: A departure
Page 159 and 160:
Glossary D-5Loop Break Alarm: This
Page 161 and 162:
Glossary D-7Serial Communications:
Page 164 and 165:
Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

Create successful ePaper yourself

Delete template?

Save as template?