Temperature Controller - Staveb AG

More documents

Recommendations

Info

C-6 Calibration6. Press the M key to set the Bulletin 900-TC32 to the state on the left. SetSTV to –9 mV. Allow the count value on the No. 2 display to fullystabilize, then press the D key to temporarily register the calibrationsetup. (Input types 0, 2, 5, 6, 8: Go to step 11.)Figure 3.87. Press the M key. The No. 2 display changes to the state on the left whenthe input type is 1, 3, 4, 7, 9, 10, 11, 12, 13, 14, or 15.8. Set STV to 54 mV. Allow the count value on the No. 2 display to fullystabilize, then press the D key to temporarily register the calibrationsetup.Figure 3.99. Press the M key. The No. 2 display changes to the state on the left whenthe input type is 1, 3, 4, 7, 9, 10, 11, 12, 13, 14, 15, 17, or 18. Set STV to–9 mV.Figure 3.1010. Allow the count value on the No. 2 display to fully stabilize, then pressthe D key to temporarily register the calibration setup.11. Press the M key to set the Bulletin 900-TC32 to the state on the left.Figure 3.1112. Change the wiring as follows:Figure 3.12900-TC328 9- +Compensating conductor of currentlyselected thermocouple.Use K thermocouple compensatingconductor for E, R, S, and B thermocoupleson non-contact temperature sensor.Open in non-connected stateINPUTSTVDMMZerocontrollerOUTPUTShortDisconnect the STV to enable the thermocouple of the cold junctioncompensator. When doing this, make sure to disconnect the wiring onthe STV side.Publication 900-UM003C-EN-E - January 2004
Calibration C-713. Allow the count value on the No. 2 display to fully stabilize, then pressthe D key to temporarily register the calibration setup.14. Press the M key. The No. 2 display changes to the state on the left.Note that the data to be temporarily registered is not displayed when it isnot entirely prepared.15. Press the U key. The No. 2 display changes to yes. Release the key andwait 2 seconds or press the M key. This stores the temporarilyregistered calibration data to EEPROM. To cancel storage oftemporarily registered calibration data to memory, press the M keywithout pressing the U key.Figure 3.1316. The calibration mode is quit by turning the power OFF.Calibrating Analog Input This example describes how to calibrate when 0…50 mV input (input type 16)is currently selected on an Bulletin 900-TC32 supporting thermocouple input.Figure 3.141 2900-TC328 9- +Input power supplySTVDMM1. Connect the power supply.2. Connect an STV and DMM to the analog input terminals, as shown inthe figure above.3. Turn the power ON.4. Move to the Calibration function group. This starts the 30-minute agingtimer. This timer provides an approximate timer for aging. After 30minutes, the No. 2 display changes to 0. You can advance to the nextstep in this procedure even if 0 is not displayed.Figure 3.15Publication 900-UM003C-EN-E - January 2004
Page 7 and 8:
Table of Contentstoc-iiiExecuting t
Page 9 and 10:
Table of Contentstoc-vMemory Error
Page 11 and 12:
PrefaceSafety PrecautionsSafety Sig
Page 13 and 14:
Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16:
Bulletin 900-TC32 Input and Output
Page 17 and 18:
Bulletin 900-TC32 Input and Output
Page 19 and 20:
Chapter 2PreparationsHardware Insta
Page 21 and 22:
Preparations 2-3System Wiring and I
Page 23 and 24:
Preparations 2-5ATTENTION!• Clean
Page 25 and 26:
Preparations 2-7Removing and Attach
Page 27 and 28:
Preparations 2-9• Separate input
Page 29 and 30:
Preparations 2-11Wiring Control Out
Page 31 and 32:
Preparations 2-13Figure 2.12 Commun
Page 33 and 34:
Chapter 3Configuration and Basic Op
Page 35 and 36:
Configuration and Basic Operation 3
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Chapter 4Parameter Adjustments and
Page 63 and 64:
Parameter Adjustments and Applicati
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Chapter 5Parameter Functions and De
Page 87 and 88:
Parameter Functions and Definitions
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98: Parameter Functions and Definitions
Page 127 and 128: Chapter 6Troubleshooting and Error
Page 129 and 130: Troubleshooting and Error Indicatio
Page 131 and 132: Appendix ASpecificationsFor the set
Page 133 and 134: A-3Sensor Input SettingRangesTable
Page 135 and 136: Appendix BParameter Operations List
Page 137 and 138: B-3Table B.C Initial Setting Functi
Page 139 and 140: B-5Figure B.1Power ONOperationfunct
Page 141 and 142: B-7Advanced setting function groupP
Page 143 and 144: Appendix CCalibrationParameter Stru
Page 145 and 146: Calibration C-3User CalibrationCali
Page 147: Calibration C-51. Connect the power
Page 151 and 152: Calibration C-91. Connect the power
Page 153 and 154: Calibration C-11Platinum Resistance
Page 155 and 156: Appendix DGlossaryAdaptive Tuning:
Page 157 and 158: Glossary D-3Deviation: A departure
Page 159 and 160: Glossary D-5Loop Break Alarm: This
Page 161 and 162: Glossary D-7Serial Communications:
Page 164 and 165: Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?