Temperature Controller - Staveb AG

More documents

Recommendations

Info

4-4 Parameter Adjustments and Application Considerations2. Prepare a thermometer (B) capable of measuring the temperature of thecontrol target (C) as shown in Figure 4.9 so that 1-point shift or 2-pointshift can be carried out.Figure 4.9 Configuration when Compensating a Non-Contact Temperature SensorNon-contacttemperaturesensor(C) Control target(B) Thermometer(A) 900-TC32Using the 1-Point Shift Method1. In the temperature control configuration shown in Figure 4.9, bring theset point to near the value at which the temperature of the control targetis to be controlled. Assume that the control target temperature (C) andthe control target temperature (B) match.Figure 4.102. Check the control target temperature (B) and the controller readout (A).Take the value from the following equation as the Input Shift Value, andconfigure the same numerical values to cns. Figure 4.11 shows theeffect of 1-point temperature input shift.Control target temperature (B) – Controller readout (A) =Input shift valuePublication 900-UM003C-EN-E - January 2004
Parameter Adjustments and Application Considerations 4-53. After you have configured the 1-point input shift value, check controllerreadout (A) and control target temperature (B). If they are almost thesame, this completes temperature input shift.Figure 4.11 One-Point Temperature Input ShiftController readout (A)Temperature readoutafter shift (e.g. 120°C)Temperature readoutbefore shift (e.g. 110°C)After shiftInput shift value (e.g. 10°C)Before shift0Near set point(e.g. 120°C)Temperature readout ofcontrol target (B)Using the 2-Point Shift MethodUse the 2-point input shift method if you want to increase the accuracy of thereadout values across the range of a non-contact sensor.1. When using the 2-point shift method, shift the controller readout at twopoints: the first, near room temperature, and the second, near the valueat which the temperature of the control target is to be controlled.Therefore, for this procedure, bring the control target temperature tonear room temperature and to near the set point, and check controltarget temperature (B) and controller readout (A) (see Figure 4.9).2. Using equations 1 and 2 (p. 4-6), calculate the upper- and lower-limittemperature input shift values from the readout and temperature to beshifted that you obtained in step 1.Figure 4.12 shows the effect of shift by 2-point temperature input shift.Publication 900-UM003C-EN-E - January 2004
Page 7 and 8:
Table of Contentstoc-iiiExecuting t
Page 9 and 10:
Table of Contentstoc-vMemory Error
Page 11 and 12:
PrefaceSafety PrecautionsSafety Sig
Page 13 and 14: Chapter 1Bulletin 900-TC32 Input an
Page 15 and 16: Bulletin 900-TC32 Input and Output
Page 17 and 18: Bulletin 900-TC32 Input and Output
Page 19 and 20: Chapter 2PreparationsHardware Insta
Page 21 and 22: Preparations 2-3System Wiring and I
Page 23 and 24: Preparations 2-5ATTENTION!• Clean
Page 25 and 26: Preparations 2-7Removing and Attach
Page 27 and 28: Preparations 2-9• Separate input
Page 29 and 30: Preparations 2-11Wiring Control Out
Page 31 and 32: Preparations 2-13Figure 2.12 Commun
Page 33 and 34: Chapter 3Configuration and Basic Op
Page 35 and 36: Configuration and Basic Operation 3
Page 61 and 62: Chapter 4Parameter Adjustments and
Page 63: Parameter Adjustments and Applicati
Page 67 and 68: Parameter Adjustments and Applicati
Page 85 and 86: Chapter 5Parameter Functions and De
Page 87 and 88: Parameter Functions and Definitions
Page 115 and 116:
Parameter Functions and Definitions
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Chapter 6Troubleshooting and Error
Page 129 and 130:
Troubleshooting and Error Indicatio
Page 131 and 132:
Appendix ASpecificationsFor the set
Page 133 and 134:
A-3Sensor Input SettingRangesTable
Page 135 and 136:
Appendix BParameter Operations List
Page 137 and 138:
B-3Table B.C Initial Setting Functi
Page 139 and 140:
B-5Figure B.1Power ONOperationfunct
Page 141 and 142:
B-7Advanced setting function groupP
Page 143 and 144:
Appendix CCalibrationParameter Stru
Page 145 and 146:
Calibration C-3User CalibrationCali
Page 147 and 148:
Calibration C-51. Connect the power
Page 149 and 150:
Calibration C-713. Allow the count
Page 151 and 152:
Calibration C-91. Connect the power
Page 153 and 154:
Calibration C-11Platinum Resistance
Page 155 and 156:
Appendix DGlossaryAdaptive Tuning:
Page 157 and 158:
Glossary D-3Deviation: A departure
Page 159 and 160:
Glossary D-5Loop Break Alarm: This
Page 161 and 162:
Glossary D-7Serial Communications:
Page 164 and 165:
Back Coverwww.rockwellautomation.co
show all

Temperature Controller - Staveb AG

Create successful ePaper yourself

Delete template?

Save as template?