Hardware and Engineering DF6-340-... Frequency ... - Moeller.com.tr

More documents

Recommendations

Info

Warning!Dangerous electrical voltage!Before <strong>com</strong>mencing the installation• Disconnect the power supply of the device.• Ensure that devices cannot be accidentally restarted.• Verify isolation from the supply.• Earth <strong>and</strong> short circuit the device.• Cover or enclose any adjacent live <strong>com</strong>ponents.• Follow the engineering instructions (AWA) for thedevice concerned.• Only suitably qualified personnel in accordance withEN 50110-1/-2 (VDE 0105 Part 100) may work on thisdevice/system.• Before installation <strong>and</strong> before touching the device ensurethat you are free of electrostatic charge.• The functional earth (FE) must be connected to the protectiveearth (PE) or the potential equalisation. The system installer isresponsible for implementing this connection.• Connecting cables <strong>and</strong> signal lines should be installed sothat inductive or capacitive interference does not impair theautomation functions.• Install automation devices <strong>and</strong> related operating elements insuch a way that they are well protected against unintentionaloperation.• Suitable safety hardware <strong>and</strong> software measures should beimplemented for the I/O interface so that an open circuit on thesignal side does not result in undefined states in theautomation devices.• Ensure a reliable electrical isolation of the extra-low voltage ofthe 24 V supply. Only use power supply units <strong>com</strong>plying withIEC 60364-4-41 (VDE 0100 Part 410) or HD384.4.41 S2.• Deviations of the mains voltage from the rated value mustnot exceed the tolerance limits given in the specifications,otherwise this may cause malfunction <strong>and</strong> dangerousoperation.• Emergency stop devices <strong>com</strong>plying with IEC/EN 60204-1 mustbe effective in all operating modes of the automation devices.Unlatching the emergency-stop devices must not cause arestart.• Devices that are designed for mounting in housings or controlcabinets must only be operated <strong>and</strong> controlled after they havebeen installed <strong>and</strong> with the housing closed. Desktop orportable units must only be operated <strong>and</strong> controlled inenclosed housings.• Measures should be taken to ensure the proper restart ofprograms interrupted after a voltage dip or failure. This shouldnot cause dangerous operating states even for a short time.If necessary, emergency-stop devices should be implemented.• Wherever faults in the automation system may cause injury ormaterial damage, external measures must be implemented toensure a safe operating state in the event of a fault ormalfunction (for example, by means of separate limit switches,mechanical interlocks etc.).• Depending on their degree of protection, frequency invertersmay contain live bright metal parts, moving or rotating<strong>com</strong>ponents or hot surfaces during <strong>and</strong> immediately afteroperation.• Removal of the required covers, improper installation orincorrect operation of motor or frequency inverter may causethe failure of the device <strong>and</strong> may lead to serious injury ordamage.• The applicable national accident prevention <strong>and</strong> safetyregulations apply to all work carried on live frequencyinverters.• The electrical installation must be carried out in accordancewith the relevant regulations (e. g. with regard to cable crosssections, fuses, PE).• Transport, installation, <strong>com</strong>missioning <strong>and</strong> maintenance workmust be carried out only by qualified personnel (IEC 60364,HD 384 <strong>and</strong> national occupational safety regulations).• Installations containing frequency inverters must be providedwith additional monitoring <strong>and</strong> protective devices inaccordance with the applicable safety regulations.Modifications to the frequency inverters using the operatingsoftware are permitted.<strong>Moeller</strong> GmbHSafety instructionsI
• All covers <strong>and</strong> doors must be kept closed during operation.• To reduce the hazards for people or equipment, the user mustinclude in the machine design measures that restrict theconsequences of a malfunction or failure of the drive(increased motor speed or sudden st<strong>and</strong>still of motor).These measures include:– Other independent devices for monitoring safety-relatedvariables (speed, travel, end positions etc.).– Electrical or non-electrical system-wide measures(electrical or mechanical interlocks).– Never touch live parts or cable connections of the frequencyinverter after it has been disconnected from the powersupply. Due to the charge in the capacitors, these parts maystill be live after disconnection. Fit appropriate warningsigns.II
Page 1: Hardware a
Page 5 and 6: Contents01/02 AWB8230-1413GB4 Opera
Page 7 and 8: Contents01/02 AWB8230-1413GB- Contr
Page 9 and 10: 601/02 AWB8230-1413GB
Page 11 and 12: About the DF6 <str
Page 17 and 18: Engineering01/02 A
Page 23 and 24: Installation01/02 AWB8230-1413GBMou
Page 25 and 26: Installation01/02 AWB8230-1413GBWit
Page 27 and 28: Installation01/02 AWB8230-1413GBFit
Page 29 and 30: Installation01/02 AWB8230-1413GBEle
Page 31 and 32: Installation01/02 AWB8230-1413GBCon
Page 33 and 34: Installation01/02 AWB8230-1413GBThe
Page 35 and 36: Installation01/02 AWB8230-1413GBPES
Page 39 and 40: Installation01/02 AWB8230-1413GBPar
Page 43 and 44: Installation01/02 AWB8230-1413GBNo.
Page 45 and 46: Installation01/02 AWB8230-1413GBhRo
Page 47 and 48: Installation01/02 AWB8230-1413GBHav
Page 49 and 50: Operating the DF60
Page 51 and 52: Operating the DF60
Page 53 and 54:
Operating the DF60
Page 55 and 56:
Operating the DF60
Page 57 and 58:
Programming the ControlSignal Termi
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
10201/02 AWB8230-1413GB
Page 107 and 108:
Setting Parameters01/02 AWB8230-141
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
......Setting Parameters01/02 AWB82
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Messages01/02 AWB8230-1413GBDisplay
Page 157 and 158:
Messages01/02 AWB8230-1413GBOther m
Page 159 and 160:
Messages01/02 AWB8230-1413GBDisplay
Page 161 and 162:
Troubleshooting01/02 AWB8230-1413GB
Page 163 and 164:
Appendix01/02 AWB8230-1413GB<strong
Page 165 and 166:
Appendix01/02 AWB8230-1413GB<strong
Page 167 and 168:
Appendix01/02 AWB8230-1413GBCables
Page 169 and 170:
Appendix01/02 AWB8230-1413GBRFI fil
Page 171 and 172:
Appendix01/02 AWB8230-1413GBPNU Fun
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Index01/02 AWB8230-1413GBFlow contr
show all

Hardware and Engineering DF6-340-... Frequency ... - Moeller.com.tr

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?