Hardware and Engineering DF6-340-... Frequency ... - Moeller.com.tr

More documents

Recommendations

Info

01/02 AWB8230-1413GB Programmable digital inputs1to5Programmable digital inputs 1 to 5Various functions can be assigned to terminals 1 to 5. Dependingon your requirements, you can configure these terminals asfollows:• anticlockwise start signal (REV),• selection inputs for various fixed frequencies (FF1 to FF4),• reset input (RST),• etc.The terminal functions for programmable digital inputs 1 to 5 areconfigured with PNU C001 to C005, i.e. with PNU C001, youspecify the function of digital input 1, with PNU C002 the functionof digital input 2, etc. Note, however, that you cannot assign thesame function to two inputs at the same time.Programmable digital inputs 1 to 5 are configured by default asmake contacts. If, therefore, you want to activate the function ofan input terminal, you must close the corresponding input (i.e.connect the input terminal to terminal P24). Conversely, todeactivate the input terminal, the input must be opened.Caution!If an EEPROM error occurs, (fault message E08), allparameters must be checked to ensure that they arecorrect (especially the RST input).Table 11: Digital inputs 1 to 5PNU Terminal Adjustable inRUN modeNormalExtendedValueC001 1 – j a table 12 18C002 2 16C003 3 03C004 4 02C005 5 01For a detailed description of the input functions, see the pageslisted in table 12.WETable 12: Functions of the digital inputsValue Function Description a page01 REV Start/stop anticlockwise 6702 FF1 First fixed frequency input 6803 FF2 Second fixed frequency input04 FF3 Third fixed frequency input05 FF4 Fourth fixed frequency input06 JOG Jog mode 7807 DB DC brake 8508 SET Selection of the second 84parameter set09 2CH Second acceleration <strong>and</strong> 73deceleration time11 FRS Motor shutdown <strong>and</strong> free run 74stop (coasting)12 EXT External fault 7513 USP Unattended start protection 7614 CS Heavy starting duty 8815 SFT Parameter protection 8116 AT Setpoint definition through 72current signal18 RST Reset 7720 STA Pulse start (3-wire) 9121 STP Pulse stop (3-wire) 9122 F/R Direction of rotation (3-wire) 9123 PID Activation of PID control 9224 PIDC Reset integral <strong>com</strong>ponent 9227 UP Acceleration82(motor potentiometer)28 DWN Deceleration82(motor potentiometer)29 UDC Reset frequency82(motor potentiometer)32 SF1 Bitwise fixed frequency 7033 SF2selection34 SF335 SF436 SF537 SF638 SF739 OLR Current limit switch over 87no NO No function –65
Programming the ControlSignal Terminals01/02 AWB8230-1413GBYou can optionally configure the digital inputs as break (NC)contacts. To do this, enter 01 under PNU C011 to C015(corresponding to digital inputs 1 to 5).An exception applies to the RST input (reset), which can only beoperated as a make (NO) contact. FW is configured as a make (NO)contact under PNU C019.Caution!If you configure digital FW or REV inputs as break contacts(the default setting is as a make contact), the motor startsimmediately. They should not be reconfigured as breakcontacts unless this is unavoidable.Table 13: Configuring digital inputs as break contactsPNU Terminal Value Adjustable in RUN mode Function WENormalExtendedC011C012C01312300 or 01 – j 00: Makecontact01: BreakcontactC014 4C015 5C019 FW0066
Page 1 and 2:
Hardware a
Page 3 and 4:
• All covers and
Page 5 and 6:
Contents01/02 AWB8230-1413GB4 Opera
Page 7 and 8:
Contents01/02 AWB8230-1413GB- Contr
Page 9 and 10:
601/02 AWB8230-1413GB
Page 11 and 12:
About the DF6 <str
Page 13 and 14:
About the DF6 <str
Page 15 and 16:
About the DF6 <str
Page 17 and 18: Engineering01/02 A
Page 23 and 24: Installation01/02 AWB8230-1413GBMou
Page 25 and 26: Installation01/02 AWB8230-1413GBWit
Page 27 and 28: Installation01/02 AWB8230-1413GBFit
Page 29 and 30: Installation01/02 AWB8230-1413GBEle
Page 31 and 32: Installation01/02 AWB8230-1413GBCon
Page 33 and 34: Installation01/02 AWB8230-1413GBThe
Page 35 and 36: Installation01/02 AWB8230-1413GBPES
Page 39 and 40: Installation01/02 AWB8230-1413GBPar
Page 43 and 44: Installation01/02 AWB8230-1413GBNo.
Page 45 and 46: Installation01/02 AWB8230-1413GBhRo
Page 47 and 48: Installation01/02 AWB8230-1413GBHav
Page 49 and 50: Operating the DF60
Page 57 and 58: Programming the ControlSignal Termi
Page 67: Programming the ControlSignal Termi
Page 105 and 106: 10201/02 AWB8230-1413GB
Page 107 and 108: Setting Parameters01/02 AWB8230-141
Page 113 and 114: ......Setting Parameters01/02 AWB82
Page 119 and 120:
Setting Parameters01/02 AWB8230-141
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Messages01/02 AWB8230-1413GBDisplay
Page 157 and 158:
Messages01/02 AWB8230-1413GBOther m
Page 159 and 160:
Messages01/02 AWB8230-1413GBDisplay
Page 161 and 162:
Troubleshooting01/02 AWB8230-1413GB
Page 163 and 164:
Appendix01/02 AWB8230-1413GB<strong
Page 165 and 166:
Appendix01/02 AWB8230-1413GB<strong
Page 167 and 168:
Appendix01/02 AWB8230-1413GBCables
Page 169 and 170:
Appendix01/02 AWB8230-1413GBRFI fil
Page 171 and 172:
Appendix01/02 AWB8230-1413GBPNU Fun
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Index01/02 AWB8230-1413GBFlow contr
show all

Hardware and Engineering DF6-340-... Frequency ... - Moeller.com.tr

Create successful ePaper yourself

Delete template?

Save as template?