Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

More documents

Recommendations

Info

AND connection, positive edgeParameter Operation mode Timer = 3InputTime 1Time 1Time 2OutputAs soon as the positive signal edge is received at the input, time 1 is started. If a positivesignal edge is detected within the delay, time 1 starts again. After the expiry ofthe delay, the output signal is switched for the signal duration time 2. Within the signalduration time 2, the output is switched off by the input signal. If the input signal ispresent during the whole time 2, the output signal remains on in this time.: Time not run out completely: Time run out completely14.5.2 ComparatorWith the help of software functions Comparator 1 and 2, various comparisons of actualvalues with percentage-adjustable fixed values can be done.The actual values to be compared can be selected from the following table with theparameters Op. Mode Comparator 1 540 and Op. Mode Comparator 2 543.If an expansion module is connected, further operation modes are available.Operation modeFunction0 - Off Comparator is switched off.1 - Absolute current R.m.s Current 211 > Rated Current 3712 - Abs. Active Current Active Current 214 > Rated Current 371Stator Frequency 210 > Maximum Frequency3 - Abs. Stator Frequency419Encoder 1 Speed 218 > maximum speed (calculatedfrom Maximum Frequency 419 and No.4 - Abs. Actual Speed 1of Pole Pairs 373)Repetition Frequency Input 252 >Maximum5 - Abs. Actual Repetition Freq.Frequency 419Winding Temp.,Winding Temperature 226 >6 -Temp. Follow-Up.temperature 100 °CActual Frequency 241 > Maximum Frequency7 - Abs. Actual Frequency4199 - DC link voltage DC Link Voltage 222 > Direct voltage 1000 V10 - Abs. Isq Isq 216 > Rated Current 37111 - Abs Filtered Active Current Active Current 214 > Rated Current 371Internal Reference Frequency 228 >12 - Abs. Internal Ref. FrequencyMaximum Frequency 419Reference Percentage Value 229 >13 - Abs. Ref. Percentage ValueMaximum Reference Percentage 519Abs. Actual Percentage Actual Percentage Value 230 >14 -ValueMaximum Reference Percentage 519Analog Input15 - Analog Input MFI1A 251 > input signal 100 %MFI1A Abs. Amount100 to 107 Operation modes with signs (+/-)136 02/06
The switch-on and switch-off thresholds for compactors 1 and 2 are set by the parametersComparator On above 541, 544 and Comparator Off below 542, 545.The percentage limits of the corresponding reference values are indicated.ParameterSettingsNo. Description Min. Max. Fact. sett.541 Comparator 1 On above - 300.00 % 300.00 % 100.00 %542 Comparator 1 Off below - 300.00 % 300.00 % 50.00 %544 Comparator 2 On above - 300.00 % 300.00 % 100.00 %545 Comparator 2 Off below - 300.00 % 300.00 % 50.00 %The setting of the percentage limits of the comparators enables the following logicallinks. The comparison with signs is possible in the corresponding operation modes ofthe comparators.1100offbelowonabove%onaboveoffbelow%14.5.3 Logic ModulesWith the Logic Modules function, it is possible to link external digital signals and internallogic signals of the frequency inverter to one another. Four identical logic modulesare available. These modules can be parameterized independent of one another. Theresults of the logic operations can be used for further functions within and outside ofthe frequency inverter. In addition to the combinatory logic functions AND, OR andEXOR, the sequential logic functions RS flip-flop, D flip-flop and Toggle flip-flop areavailable.Each module has two logic inputs and one logic output. The inputs can be parameterizedand can be assigned to different signal sources. The signal sources are listed inthe logic table in chapter "Digital Inputs". Additionally, the logic modules can be interconnectedto each other via the corresponding parameterization. The functionality ofthe parameters is the same in each of the four logic modules.Note:The logic modules are processed internally in the frequency inverter oneafter the other depending on their number. For example, logic module 1is processed before logic module 2.When designing application-specific logic links, e.g. in the case of timecriticalapplications, make sure to comply with the correct order of thelogic modules.02/06 137
Page 1:
INDUSTRYPROCESSAND AUTOMATION SOLUT
Page 4 and 5:
TABLE OF CONTENTS1. General Safety
Page 6 and 7:
TABLE OF CONTENTS7 Commissioning of
Page 8 and 9:
TABLE OF CONTENTS13.10 Motor Potent
Page 10 and 11:
TABLE OF CONTENTS19 Error Protocol.
Page 12 and 13:
1.2 Purpose of the Frequency Invert
Page 14 and 15:
2 Scope of SupplyThanks to the modu
Page 16 and 17:
2.3 Frequency Inverter (18.5 up to
Page 18 and 19:
3 Technical Data3.1 Frequency Inver
Page 20 and 21:
3.3 Frequency Inverter 400 V (5.5 u
Page 22 and 23:
3.5 Frequency Inverter 400 V (37.0
Page 24 and 25:
4 Mechanical InstallationThe freque
Page 26 and 27:
4.2 Frequency Inverter (5.5 to 15.0
Page 28 and 29:
4.4 Frequency inverter (37.0 up to
Page 30 and 31:
5.1 EMC InformationThe frequency in
Page 32 and 33:
5.3 Mains ConnectionThe mains fuses
Page 34 and 35:
5.3.3 Frequency Inverter (18.5 up t
Page 36 and 37:
5.4 Motor ConnectionThe connection
Page 38 and 39:
5.4.2 Frequency Inverter (5.5 up to
Page 40 and 41:
5.4.4 Frequency Inverter (37.0 up t
Page 42 and 43:
5.5.2 Frequency Inverter (5.5 up to
Page 44 and 45:
5.6 Control TerminalsThe control an
Page 46 and 47:
5.6.2 Control Terminals - Terminal
Page 48 and 49:
5.6.2.4 Configuration 411 - Sensorl
Page 50 and 51:
5.7 Optional ComponentsThanks to th
Page 54 and 55:
6.4 Parameter Menu (PARA)The parame
Page 56 and 57:
Function - ActOnly the active param
Page 58 and 59:
6.5.6 Error MessagesThe copy functi
Page 60 and 61:
Activation via CM Communication Mod
Page 62 and 63:
6.8 Controlling the Motor via the C
Page 64 and 65:
7 Commissioning of the Frequency In
Page 66 and 67:
7.2.2 Data SetThe data set change-o
Page 68 and 69:
101 -104 -Operation modeSingle eval
Page 70 and 71:
Warning!Switch off power supply bef
Page 72 and 73:
7.2.8.2 Set points at multi-functio
Page 74 and 75:
Operation mode24 - Check Machine Da
Page 76 and 77:
8.3 Inverter Software VersionThe fi
Page 78 and 79:
In the table, you will find a list
Page 80 and 81:
9 Machine DataThe input of the mach
Page 82 and 83:
9.2.4 Rated Slip Correction FactorT
Page 84 and 85:
10 System DataThe various control f
Page 86 and 87:
Operation mode3 -4 -12 -14 -Magneti
Page 88 and 89: 11.2 Stopping BehaviorThe stopping
Page 90 and 91: 11.2.1 Switch-Off ThresholdThe Swit
Page 92 and 93: 11.5 Search RunThe synchronization
Page 94: 11.6.1 Reference PositioningThe fee
Page 97 and 98: 11.6.2 Axis PositioningFor axis pos
Page 99 and 100: 12 Error and warning behaviorOperat
Page 101 and 102: 12.6 Motor TemperatureThe configura
Page 103 and 104: 13 Reference ValuesThe ACT series f
Page 105 and 106: 13.4.1 Block DiagramThe following t
Page 107 and 108: 13.5 Reference Percentage ChannelTh
Page 109 and 110: 13.6 Fixed Reference ValuesThe fixe
Page 111 and 112: The ramps for Emergency Stop Clockw
Page 113 and 114: 13.8 Percentage Value RampsThe perc
Page 115 and 116: The Operation Mode 474 of the motor
Page 117 and 118: 13.11 Repetition frequency inputThe
Page 119 and 120: The following characteristic is set
Page 121 and 122: The default Minimum Frequency 418 o
Page 123 and 124: 14.2.1 Analog Output MFO1ABy defaul
Page 125 and 126: 14.3 Digital OutputsThe OP. Mode Di
Page 127 and 128: 14.3.4 Open brakeThe Open brake fun
Page 129 and 130: Operation modeFunctionThe DC link v
Page 131 and 132: Operation modeFunction158 - Timer 1
Page 133 and 134: 14.4.1 Start commandThe parameters
Page 135 and 136: 14.4.8 Fixed Value Change-OverDepen
Page 137: 14.5.1.1 Time ConstantThe logic seq
Page 141 and 142: Examples of the logic functions dep
Page 143 and 144: Parameter Operation Mode Logic = 30
Page 145 and 146: The default Cut-Off Voltage 603 (UC
Page 147 and 148: 16.2 Voltage controllerThe voltage
Page 149 and 150: ParameterSettingsNo. Description Mi
Page 151 and 152: 16.3 Technology ControllerThe techn
Page 153 and 154: Structural image:Technology control
Page 155 and 156: Behavior in generator operation:If
Page 157 and 158: 16.5.2.1 Limit Value SourcesThe lim
Page 159 and 160: −−−The output value of the co
Page 161 and 162: Optimization of the controller para
Page 163 and 164: 17 Special FunctionsThe configurabl
Page 165 and 166: Operation modeFunctionControl via K
Page 167 and 168: 17.4.1 Dimensioning of Brake Resist
Page 169 and 170: Multiple motor operationParameter O
Page 171 and 172: 17.7.2 Temperature AdjustmentThe fi
Page 173 and 174: 18 Actual ValuesThe various control
Page 175 and 176: 18.3 Actual Value MemoryThe assessm
Page 177 and 178: 18.4.2 Volume Flow and PressureThe
Page 179 and 180: InsideCodeMeaningF0300 Inside tempe
Page 181 and 182: Error Environment357 Int. Value 1 S
Page 183 and 184: A decimal value is displayed, indic
Page 185 and 186: 21 Parameter ListThe parameter list
Page 187 and 188: Error EnvironmentNo. Description Un
Page 189 and 190:
Controlled commissioningNo. Descrip
Page 191 and 192:
Fixed FrequenciesNo. Description Un
Page 193 and 194:
Search RunNo. Description Unit Sett
Page 195 and 196:
INDUSTRY PROCESSAND AUTOMATION SOLU
show all

Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

Create successful ePaper yourself

Delete template?

Save as template?