Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

More documents

Recommendations

Info

6.8 Controlling the Motor via the Control UnitThe control unit enables controlling the connected motor in accordance with the selectedoperation mode of parameter Local/Remote 412.Note:In order to be able to control the drive via the control unit, the digitalcontroller input S1IND (controller release) must be connected and set to"High-Signal" in order to enable the output stage.Warning! • Switch off power supply before connecting and disconnecting controlterminal S1IND.• The unit may only be connected with the power supply switched off.• Make sure that the frequency inverter is discharged.• When the frequency inverter is disconnected from power supply, themains, DC-link voltage and motor terminals may still be live forsome time. Wait for some minutes until the DC link capacitors havedischarged before starting to work at the unit.: When the RUN key was pressed, the drive was in operation already.The CTRL menu branch can be accessed via the navigationwithin the menu structure. The CtrL function contains subfunctionswhich are displayed according to the operating pointof the frequency inverter.Press the RUN key anywhere within the menu structure toaccess the motor potentiometer function PotF. for clockwiseoperation or Potr for anti-clockwise operation directly.If the drive is running already, the display reads intF (clockwiseoperation) / intr (anti-clockwise operation) for the functioninternal reference value or inPF (clockwise operation) /inPr (anti-clockwise operation) for the function"Motorpoti (KP)".The function Motorpoti (KP) enables a link to other referencevalue sources in the frequency reference value channel. Thefunction is described in Chapter “Motorpoti (KP)”.60 02/06
Motor potentiometer function PotUse the arrow keys to adjust the output frequency of the frequencyinverter from the minimum frequency 418 to themaximum frequency 419. The acceleration corresponds to thefactory settings (2 Hz/s) for parameter Ramp Keypad-Motorpoti 473. The parameters Acceleration (Clockwise) 420and Deceleration (Clockwise) 421 are considered in the caseof low acceleration values.Function Motorpoti (KP) inPUse the arrow keys to adjust the output frequency of the frequencyinverter from the Minimum Frequency 418 to theMaximum Frequency 419. The adjusted frequency value bymeans of the control unit can be connected with further referencevalues via Reference Frequency Source 475. (Refer tochapter “Frequency Reference Channel” and "Motorpoti (KP)".)Internal reference value intThe drive is in operation, i.e. output signals are present at thefrequency inverter and the current actual value is displayed.Press an arrow key to switch to the motor potentiometer functionPot. The current frequency value is taken over in the motorpotentiometer function Pot.JOG frequency JOGThis function is useful for manual setup and positioning of amachine. The frequency of the output signal is set to the enteredvalue if the FUN key is pressed.• press FUN key to switch from the internal reference valueint or the motor potentiometer function Pot to the parameterJOG frequency 489.• Keep the FUN key pressed and press the arrow keys toadjust the required frequency.• (The frequency value last adjusted is saved as the JOGfrequency 489.)• Release the FUN key to stop the drive.• (The display returns to the previous function Pot or int orto inP if function "Motorpoti (KP)" is active.)ENTESCFUNRUNSTOPKey functionsReversal of the direction of rotation independent of the control signal onthe terminals Clockwise S2IND or Anticlockwise S3IND.Cancel function and return to the menu structure.Switch from internal set point int or rather motor potentiometer functionPot to JOG frequency; the drive starts.Release the key to switch to the sub-function and stop the drive.Start drive; alternative to control signal S2IND or S3INDStop drive; alternative to control signal S2IND or S3INDAttention!If you press the ENT key, the direction of rotation is changed independentof the signal on the terminals Clockwise S2IND or AnticlockwiseS3IND.If the minimum frequency 418 has been set to 0.00 Hz, the directionof rotation of the motor changes as soon as the sign of the referencefrequency value changes.02/06 61
Page 1:
INDUSTRYPROCESSAND AUTOMATION SOLUT
Page 4 and 5:
TABLE OF CONTENTS1. General Safety
Page 6 and 7:
TABLE OF CONTENTS7 Commissioning of
Page 8 and 9:
TABLE OF CONTENTS13.10 Motor Potent
Page 10 and 11:
TABLE OF CONTENTS19 Error Protocol.
Page 12 and 13: 1.2 Purpose of the Frequency Invert
Page 14 and 15: 2 Scope of SupplyThanks to the modu
Page 16 and 17: 2.3 Frequency Inverter (18.5 up to
Page 18 and 19: 3 Technical Data3.1 Frequency Inver
Page 20 and 21: 3.3 Frequency Inverter 400 V (5.5 u
Page 22 and 23: 3.5 Frequency Inverter 400 V (37.0
Page 24 and 25: 4 Mechanical InstallationThe freque
Page 26 and 27: 4.2 Frequency Inverter (5.5 to 15.0
Page 28 and 29: 4.4 Frequency inverter (37.0 up to
Page 30 and 31: 5.1 EMC InformationThe frequency in
Page 32 and 33: 5.3 Mains ConnectionThe mains fuses
Page 34 and 35: 5.3.3 Frequency Inverter (18.5 up t
Page 36 and 37: 5.4 Motor ConnectionThe connection
Page 38 and 39: 5.4.2 Frequency Inverter (5.5 up to
Page 40 and 41: 5.4.4 Frequency Inverter (37.0 up t
Page 42 and 43: 5.5.2 Frequency Inverter (5.5 up to
Page 44 and 45: 5.6 Control TerminalsThe control an
Page 46 and 47: 5.6.2 Control Terminals - Terminal
Page 48 and 49: 5.6.2.4 Configuration 411 - Sensorl
Page 50 and 51: 5.7 Optional ComponentsThanks to th
Page 54 and 55: 6.4 Parameter Menu (PARA)The parame
Page 56 and 57: Function - ActOnly the active param
Page 58 and 59: 6.5.6 Error MessagesThe copy functi
Page 60 and 61: Activation via CM Communication Mod
Page 64 and 65: 7 Commissioning of the Frequency In
Page 66 and 67: 7.2.2 Data SetThe data set change-o
Page 68 and 69: 101 -104 -Operation modeSingle eval
Page 70 and 71: Warning!Switch off power supply bef
Page 72 and 73: 7.2.8.2 Set points at multi-functio
Page 74 and 75: Operation mode24 - Check Machine Da
Page 76 and 77: 8.3 Inverter Software VersionThe fi
Page 78 and 79: In the table, you will find a list
Page 80 and 81: 9 Machine DataThe input of the mach
Page 82 and 83: 9.2.4 Rated Slip Correction FactorT
Page 84 and 85: 10 System DataThe various control f
Page 86 and 87: Operation mode3 -4 -12 -14 -Magneti
Page 88 and 89: 11.2 Stopping BehaviorThe stopping
Page 90 and 91: 11.2.1 Switch-Off ThresholdThe Swit
Page 92 and 93: 11.5 Search RunThe synchronization
Page 94: 11.6.1 Reference PositioningThe fee
Page 97 and 98: 11.6.2 Axis PositioningFor axis pos
Page 99 and 100: 12 Error and warning behaviorOperat
Page 101 and 102: 12.6 Motor TemperatureThe configura
Page 103 and 104: 13 Reference ValuesThe ACT series f
Page 105 and 106: 13.4.1 Block DiagramThe following t
Page 107 and 108: 13.5 Reference Percentage ChannelTh
Page 109 and 110: 13.6 Fixed Reference ValuesThe fixe
Page 111 and 112: The ramps for Emergency Stop Clockw
Page 113 and 114:
13.8 Percentage Value RampsThe perc
Page 115 and 116:
The Operation Mode 474 of the motor
Page 117 and 118:
13.11 Repetition frequency inputThe
Page 119 and 120:
The following characteristic is set
Page 121 and 122:
The default Minimum Frequency 418 o
Page 123 and 124:
14.2.1 Analog Output MFO1ABy defaul
Page 125 and 126:
14.3 Digital OutputsThe OP. Mode Di
Page 127 and 128:
14.3.4 Open brakeThe Open brake fun
Page 129 and 130:
Operation modeFunctionThe DC link v
Page 131 and 132:
Operation modeFunction158 - Timer 1
Page 133 and 134:
14.4.1 Start commandThe parameters
Page 135 and 136:
14.4.8 Fixed Value Change-OverDepen
Page 137 and 138:
14.5.1.1 Time ConstantThe logic seq
Page 139 and 140:
The switch-on and switch-off thresh
Page 141 and 142:
Examples of the logic functions dep
Page 143 and 144:
Parameter Operation Mode Logic = 30
Page 145 and 146:
The default Cut-Off Voltage 603 (UC
Page 147 and 148:
16.2 Voltage controllerThe voltage
Page 149 and 150:
ParameterSettingsNo. Description Mi
Page 151 and 152:
16.3 Technology ControllerThe techn
Page 153 and 154:
Structural image:Technology control
Page 155 and 156:
Behavior in generator operation:If
Page 157 and 158:
16.5.2.1 Limit Value SourcesThe lim
Page 159 and 160:
−−−The output value of the co
Page 161 and 162:
Optimization of the controller para
Page 163 and 164:
17 Special FunctionsThe configurabl
Page 165 and 166:
Operation modeFunctionControl via K
Page 167 and 168:
17.4.1 Dimensioning of Brake Resist
Page 169 and 170:
Multiple motor operationParameter O
Page 171 and 172:
17.7.2 Temperature AdjustmentThe fi
Page 173 and 174:
18 Actual ValuesThe various control
Page 175 and 176:
18.3 Actual Value MemoryThe assessm
Page 177 and 178:
18.4.2 Volume Flow and PressureThe
Page 179 and 180:
InsideCodeMeaningF0300 Inside tempe
Page 181 and 182:
Error Environment357 Int. Value 1 S
Page 183 and 184:
A decimal value is displayed, indic
Page 185 and 186:
21 Parameter ListThe parameter list
Page 187 and 188:
Error EnvironmentNo. Description Un
Page 189 and 190:
Controlled commissioningNo. Descrip
Page 191 and 192:
Fixed FrequenciesNo. Description Un
Page 193 and 194:
Search RunNo. Description Unit Sett
Page 195 and 196:
INDUSTRY PROCESSAND AUTOMATION SOLU
show all

Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

Create successful ePaper yourself

Delete template?

Save as template?