Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

More documents

Recommendations

Info

6.5.6 Error MessagesThe copy function archives all parameters, regardless of theaccess control and the value range. Some of the parametersare only writable if the frequency inverter is not in operation.The controller input (S1IND) may not be activated during thecopy operation, otherwise the data transmission is aborted.The message FUF and the number of the last parameter whichwas copied are displayed. If the controller enable input is deactivatedagain, the aborted copy operation is continued.The data transmission from the selected source to the destinationis continuously monitored by the copy function. If an erroroccurs, the copy operation is aborted and the message Errand an error code are displayed.Error MessagesCodeMeaning0 1 Write error in memory of control unit;repeat the copy operation. If error message is displayed again, formatthe memory.2 Read error in memory of control unit;repeat the copy operation. If error message is displayed again, formatthe memory.3 The size of the memory of the control unit was not determined correctly.If this error occurs repeatedly, replace the control unit.4 Not enough memory; the data are incomplete.Delete the incomplete file and date no longer needed from the controlunit.5 The communication has been disturbed or interrupted;repeat the copy operation, delete the incomplete file if necessary.1 0 Invalid identification of a file in the control unit;delete faulty file and format memory if necessary.2 The memory space of the selected target file is occupied;delete file or use different target file in the control unit.3 The source file to be read in the control unit is empty;only files containing reasonable data should be selected as a source.4 Defective file in control unit;delete faulty file and format memory, if necessary.2 0 The memory in the control unit is not formatted;format the memory via the FOr function in the copy menu.3 0 Error during reading of a parameter from the frequency inverter;check connection between the control unit and the frequency inverterand repeat reading operation.1 Error during writing of a parameter in the frequency inverter;Check connection between the control unit and the frequency inverterand repeat the writing operation.2 Unknown parameter type;delete faulty file and format memory if necessary.4 0 The communication has been disturbed or interrupted;repeat the copy operation, delete the incomplete file if necessary.56 02/06
6.6 Read data from the KP 500 control unitThe Parameter transfer operation mode enables the transmission of data from theKP 500 control unit to the frequency inverter. In this operation mode, all functions ofthe control unit are disabled except for the COPY function. Data transmission from thefrequency inverter to the control unit is also disabled.Activation of the KP 500 control unit for Parameter transfer mode is prepared via theparameter Program(ming) 34. For this purpose, the KP 500 control unit must be connectedto the frequency inverter.Operation modeFunctionThe KP 500 control unit is prepared for parameter111 - Parameter transfer transmission. A connected frequency inverter can receivedata from the control unit.110 - Normal mode Reset the KP 500 control unit to standard modeAttention! The KP 500 control unit can be activated for Parameter transfer only ifat least one file is stored in the control unit. Otherwise, the error message"F0A10" will be displayed.6.6.1 ActivatingThe KP 500 control unit can be configured both via the keys of the KP 500 and via anyother available CM communication module. To configure and activate the KP 500 controlunit, proceed as follows:Activation via keyboard of the control unit• In the parameter menu PARA, use the arrow keys to select parameter Program(ming)34 and confirm the selection by pressing the ENT key.• Use the arrow keys to enter the value 111 – Parameter transfer and confirm yourselection by pressing the ENT key.Now, the control unit is ready for activation.Before data can be transferred, the control unit must be initialized.• Disconnect the control unit from the frequency inverter and re-connect it to thesame or another frequency inverter.The initialization operation is started. During the initialization, init and a progressindicator are displayed. After the initialization, the KP 500 control unit is ready fortransferring data to the frequency inverter.Note:Setting the parameter Program(ing) 34 to 111 – Parameter transfercan be undone by means of the control unit, provided that the controlunit has not been initialized yet.• In parameter Program(ing) 34, use the arrow keys to enter thevalue 110 – Normal Mode and confirm by pressing the ENT key.02/06 57
Page 1:
INDUSTRYPROCESSAND AUTOMATION SOLUT
Page 4 and 5:
TABLE OF CONTENTS1. General Safety
Page 6 and 7:
TABLE OF CONTENTS7 Commissioning of
Page 8 and 9: TABLE OF CONTENTS13.10 Motor Potent
Page 10 and 11: TABLE OF CONTENTS19 Error Protocol.
Page 12 and 13: 1.2 Purpose of the Frequency Invert
Page 14 and 15: 2 Scope of SupplyThanks to the modu
Page 16 and 17: 2.3 Frequency Inverter (18.5 up to
Page 18 and 19: 3 Technical Data3.1 Frequency Inver
Page 20 and 21: 3.3 Frequency Inverter 400 V (5.5 u
Page 22 and 23: 3.5 Frequency Inverter 400 V (37.0
Page 24 and 25: 4 Mechanical InstallationThe freque
Page 26 and 27: 4.2 Frequency Inverter (5.5 to 15.0
Page 28 and 29: 4.4 Frequency inverter (37.0 up to
Page 30 and 31: 5.1 EMC InformationThe frequency in
Page 32 and 33: 5.3 Mains ConnectionThe mains fuses
Page 34 and 35: 5.3.3 Frequency Inverter (18.5 up t
Page 36 and 37: 5.4 Motor ConnectionThe connection
Page 38 and 39: 5.4.2 Frequency Inverter (5.5 up to
Page 40 and 41: 5.4.4 Frequency Inverter (37.0 up t
Page 42 and 43: 5.5.2 Frequency Inverter (5.5 up to
Page 44 and 45: 5.6 Control TerminalsThe control an
Page 46 and 47: 5.6.2 Control Terminals - Terminal
Page 48 and 49: 5.6.2.4 Configuration 411 - Sensorl
Page 50 and 51: 5.7 Optional ComponentsThanks to th
Page 54 and 55: 6.4 Parameter Menu (PARA)The parame
Page 56 and 57: Function - ActOnly the active param
Page 60 and 61: Activation via CM Communication Mod
Page 62 and 63: 6.8 Controlling the Motor via the C
Page 64 and 65: 7 Commissioning of the Frequency In
Page 66 and 67: 7.2.2 Data SetThe data set change-o
Page 68 and 69: 101 -104 -Operation modeSingle eval
Page 70 and 71: Warning!Switch off power supply bef
Page 72 and 73: 7.2.8.2 Set points at multi-functio
Page 74 and 75: Operation mode24 - Check Machine Da
Page 76 and 77: 8.3 Inverter Software VersionThe fi
Page 78 and 79: In the table, you will find a list
Page 80 and 81: 9 Machine DataThe input of the mach
Page 82 and 83: 9.2.4 Rated Slip Correction FactorT
Page 84 and 85: 10 System DataThe various control f
Page 86 and 87: Operation mode3 -4 -12 -14 -Magneti
Page 88 and 89: 11.2 Stopping BehaviorThe stopping
Page 90 and 91: 11.2.1 Switch-Off ThresholdThe Swit
Page 92 and 93: 11.5 Search RunThe synchronization
Page 94: 11.6.1 Reference PositioningThe fee
Page 97 and 98: 11.6.2 Axis PositioningFor axis pos
Page 99 and 100: 12 Error and warning behaviorOperat
Page 101 and 102: 12.6 Motor TemperatureThe configura
Page 103 and 104: 13 Reference ValuesThe ACT series f
Page 105 and 106: 13.4.1 Block DiagramThe following t
Page 107 and 108: 13.5 Reference Percentage ChannelTh
Page 109 and 110:
13.6 Fixed Reference ValuesThe fixe
Page 111 and 112:
The ramps for Emergency Stop Clockw
Page 113 and 114:
13.8 Percentage Value RampsThe perc
Page 115 and 116:
The Operation Mode 474 of the motor
Page 117 and 118:
13.11 Repetition frequency inputThe
Page 119 and 120:
The following characteristic is set
Page 121 and 122:
The default Minimum Frequency 418 o
Page 123 and 124:
14.2.1 Analog Output MFO1ABy defaul
Page 125 and 126:
14.3 Digital OutputsThe OP. Mode Di
Page 127 and 128:
14.3.4 Open brakeThe Open brake fun
Page 129 and 130:
Operation modeFunctionThe DC link v
Page 131 and 132:
Operation modeFunction158 - Timer 1
Page 133 and 134:
14.4.1 Start commandThe parameters
Page 135 and 136:
14.4.8 Fixed Value Change-OverDepen
Page 137 and 138:
14.5.1.1 Time ConstantThe logic seq
Page 139 and 140:
The switch-on and switch-off thresh
Page 141 and 142:
Examples of the logic functions dep
Page 143 and 144:
Parameter Operation Mode Logic = 30
Page 145 and 146:
The default Cut-Off Voltage 603 (UC
Page 147 and 148:
16.2 Voltage controllerThe voltage
Page 149 and 150:
ParameterSettingsNo. Description Mi
Page 151 and 152:
16.3 Technology ControllerThe techn
Page 153 and 154:
Structural image:Technology control
Page 155 and 156:
Behavior in generator operation:If
Page 157 and 158:
16.5.2.1 Limit Value SourcesThe lim
Page 159 and 160:
−−−The output value of the co
Page 161 and 162:
Optimization of the controller para
Page 163 and 164:
17 Special FunctionsThe configurabl
Page 165 and 166:
Operation modeFunctionControl via K
Page 167 and 168:
17.4.1 Dimensioning of Brake Resist
Page 169 and 170:
Multiple motor operationParameter O
Page 171 and 172:
17.7.2 Temperature AdjustmentThe fi
Page 173 and 174:
18 Actual ValuesThe various control
Page 175 and 176:
18.3 Actual Value MemoryThe assessm
Page 177 and 178:
18.4.2 Volume Flow and PressureThe
Page 179 and 180:
InsideCodeMeaningF0300 Inside tempe
Page 181 and 182:
Error Environment357 Int. Value 1 S
Page 183 and 184:
A decimal value is displayed, indic
Page 185 and 186:
21 Parameter ListThe parameter list
Page 187 and 188:
Error EnvironmentNo. Description Un
Page 189 and 190:
Controlled commissioningNo. Descrip
Page 191 and 192:
Fixed FrequenciesNo. Description Un
Page 193 and 194:
Search RunNo. Description Unit Sett
Page 195 and 196:
INDUSTRY PROCESSAND AUTOMATION SOLU
show all

Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

Create successful ePaper yourself

Delete template?

Save as template?