Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

More documents

Recommendations

Info

11.5 Search RunThe synchronization to a rotating drive is necessary in applications which drive themotor by their behavior or in which the drive is still rotating after a fault switch-off.Via Operation Mode 645 = Search Run, the motor speed is synchronized to the currentmotor speed without an "Overcurrent" fault message. After this, the motor isaccelerated to the reference speed at the set acceleration. This synchronization functiondetermines the current rotary frequency of the drive via a search run in operationmodes 1 to 5.The synchronization in operation modes 10 to 15 is accelerated by short test impulses.Rotary frequencies of up to 250 Hz are determined within 100 ms to 300 ms. Forhigher frequencies, a wrong frequency is determined and the synchronization fails. Inthe "Quick synchronization" operation modes, the search run cannot determinewhether an synchronization attempt has failed.Operation modeFunction0 - Off The synchronization to a rotating drive is deactivated.The search direction is defined by the sign in front of thereference value. If a positive reference value (clockwiseSearch direction acc.field of rotation) is entered, the search is in a positive1 - to specified referencevaluedirection (clockwise field of rotation), with a negativereference value, the search is in a negative direction (anticlockwisefield of rotation).2 -3 -First clockwise, thenanti-clockwise,DCBFirst anti-clockwise,then clockwise,DCB4 - Clockwise only, DCB5 -10 -11 -14 -15 -Anti-clockwise only,DCBQuick SynchronizationQuick Synch. acc. toPreset ValueQuick Sync., ClockwiseOnlyQuick Sync., AnticlockwiseOnlyThe first attempt is to synchronize to the drive in positivedirection (clockwise field of rotation). If this attempt fails,it is tried to synchronize to the drive in negative direction(anticlockwise field of rotation).The first attempt is to synchronize to the drive in negativedirection (anticlockwise field of rotation). If this attemptfails, it is tried to synchronize to the drive in positive direction(clockwise field of rotation).Synchronization to the drive is only done in positive direction(clockwise field of rotation).Synchronization to the drive is only done in negative direction(anticlockwise field of rotation).An attempt is made to synchronize to the drive in positivedirection (clockwise field of rotation) and in negative direction(anticlockwise field of rotation).The search direction is defined by the sign in front of thereference value. If a positive reference value (clockwisefield of rotation) is entered, the search is in a positivedirection (clockwise field of rotation), with a negativereference value, the search is in a negative direction (anticlockwisefield of rotation).Synchronization to the drive is only done in positive direction(clockwise field of rotation).Synchronization to the drive is only done in negative direction(anticlockwise field of rotation).Operation modes 1, 4 and 5 define a direction of rotation for the search run and avoida deviating direction. The search run can accelerate drives by checking the rotaryfrequency if the drives have a low moment of inertia and/or a small load moment.In operation modes 10 to 15, it cannot be ruled out that a wrong direction of rotationis determined in quick synchronization. For example, a frequency not equal to zeromay be determined although the drive is at a standstill. If there is no overcurrent, thedrive is accelerated accordingly. The direction of rotation is defined in operationmodes 11, 14 and 15.90 02/06
The synchronization changes the parameterized starting behavior of the selected configuration.First, the start command activates the search run in order to determine therotary frequency of the drive. In operation modes 1 to 5, the Current / Rated motorcurrent 647 is used for synchronization as a percentage of the Rated current 371.ParameterSettingsNo. Description Min. Max. Fact. sett.647 Current / Rated Motor Current 1.00 % 100.00 % 70.00 %The sensor-less control is extended for the search run by a PI-Controller, which regulatesthe parameterized Current / Rated Motor Current 647. The proportional andintegrating part of the current controller can be set via the parameters Amplification648 and Integral Time 649. The control functions can be deactivated by setting theparameters to 0.ParameterSettingsNo. Description Min. Max. Fact. sett.648 Amplification 0.00 10.00 1.00649 Integral Time 0 ms 1000 ms 20 msIf the parameter for synchronization Operation Mode 645 was set to operation mode1 to 5 (search run), the search run is not started before the Demagnetizing Time 633has elapsed.If synchronization to the drive is not possible, the Braking Current 631 is impressedinto the motor in operation modes 1 to 5 for the duration of the Break.-Time afterSearch Run 646. The impression of the direct current set in the parameters of thedirect current brake results in the motor heating up and should only be done for ashort period in the case of internally ventilated motors.ParameterSettingsNo. Description Min. Max. Fact. sett.646 Break. Time after Search Run 0.0 s 200.0 s 10.0 s11.6 PositioningPositioning is done in operation mode "Reference positioning" via the definition of thepositioning distance or in operation mode "Axis positioning" via the definition of theposition angle.Reference positioning uses a digital reference signal from a selectable signal sourcefor positioning the drive independent of the speed.Axis positioning uses a digital reference signal from a speed sensor.The function "Reference positioning" is available in configurations 110, 410 and 210and is activated by selecting operation mode 1 for parameter Operation Mode 458.The function "Axis positioning" is available in configuration 210 (Operation mode 210for parameter Configuration 30) and is activated by selecting operation mode 2 forparameter Operation Mode 458.Operation modeFunction0 - Off Positioning switched off.Positioning from reference point via definition of1 - Reference positioning positioning distance (rotations). The referencepoint is acquired via a Signal Source 459.Positioning from reference point via definition of2 - Axis Positioningthe positioning angle, reference signal from speedsensor02/06 91
Page 1:
INDUSTRYPROCESSAND AUTOMATION SOLUT
Page 4 and 5:
TABLE OF CONTENTS1. General Safety
Page 6 and 7:
TABLE OF CONTENTS7 Commissioning of
Page 8 and 9:
TABLE OF CONTENTS13.10 Motor Potent
Page 10 and 11:
TABLE OF CONTENTS19 Error Protocol.
Page 12 and 13:
1.2 Purpose of the Frequency Invert
Page 14 and 15:
2 Scope of SupplyThanks to the modu
Page 16 and 17:
2.3 Frequency Inverter (18.5 up to
Page 18 and 19:
3 Technical Data3.1 Frequency Inver
Page 20 and 21:
3.3 Frequency Inverter 400 V (5.5 u
Page 22 and 23:
3.5 Frequency Inverter 400 V (37.0
Page 24 and 25:
4 Mechanical InstallationThe freque
Page 26 and 27:
4.2 Frequency Inverter (5.5 to 15.0
Page 28 and 29:
4.4 Frequency inverter (37.0 up to
Page 30 and 31:
5.1 EMC InformationThe frequency in
Page 32 and 33:
5.3 Mains ConnectionThe mains fuses
Page 34 and 35:
5.3.3 Frequency Inverter (18.5 up t
Page 36 and 37:
5.4 Motor ConnectionThe connection
Page 38 and 39:
5.4.2 Frequency Inverter (5.5 up to
Page 40 and 41:
5.4.4 Frequency Inverter (37.0 up t
Page 42 and 43: 5.5.2 Frequency Inverter (5.5 up to
Page 44 and 45: 5.6 Control TerminalsThe control an
Page 46 and 47: 5.6.2 Control Terminals - Terminal
Page 48 and 49: 5.6.2.4 Configuration 411 - Sensorl
Page 50 and 51: 5.7 Optional ComponentsThanks to th
Page 54 and 55: 6.4 Parameter Menu (PARA)The parame
Page 56 and 57: Function - ActOnly the active param
Page 58 and 59: 6.5.6 Error MessagesThe copy functi
Page 60 and 61: Activation via CM Communication Mod
Page 62 and 63: 6.8 Controlling the Motor via the C
Page 64 and 65: 7 Commissioning of the Frequency In
Page 66 and 67: 7.2.2 Data SetThe data set change-o
Page 68 and 69: 101 -104 -Operation modeSingle eval
Page 70 and 71: Warning!Switch off power supply bef
Page 72 and 73: 7.2.8.2 Set points at multi-functio
Page 74 and 75: Operation mode24 - Check Machine Da
Page 76 and 77: 8.3 Inverter Software VersionThe fi
Page 78 and 79: In the table, you will find a list
Page 80 and 81: 9 Machine DataThe input of the mach
Page 82 and 83: 9.2.4 Rated Slip Correction FactorT
Page 84 and 85: 10 System DataThe various control f
Page 86 and 87: Operation mode3 -4 -12 -14 -Magneti
Page 88 and 89: 11.2 Stopping BehaviorThe stopping
Page 90 and 91: 11.2.1 Switch-Off ThresholdThe Swit
Page 94: 11.6.1 Reference PositioningThe fee
Page 97 and 98: 11.6.2 Axis PositioningFor axis pos
Page 99 and 100: 12 Error and warning behaviorOperat
Page 101 and 102: 12.6 Motor TemperatureThe configura
Page 103 and 104: 13 Reference ValuesThe ACT series f
Page 105 and 106: 13.4.1 Block DiagramThe following t
Page 107 and 108: 13.5 Reference Percentage ChannelTh
Page 109 and 110: 13.6 Fixed Reference ValuesThe fixe
Page 111 and 112: The ramps for Emergency Stop Clockw
Page 113 and 114: 13.8 Percentage Value RampsThe perc
Page 115 and 116: The Operation Mode 474 of the motor
Page 117 and 118: 13.11 Repetition frequency inputThe
Page 119 and 120: The following characteristic is set
Page 121 and 122: The default Minimum Frequency 418 o
Page 123 and 124: 14.2.1 Analog Output MFO1ABy defaul
Page 125 and 126: 14.3 Digital OutputsThe OP. Mode Di
Page 127 and 128: 14.3.4 Open brakeThe Open brake fun
Page 129 and 130: Operation modeFunctionThe DC link v
Page 131 and 132: Operation modeFunction158 - Timer 1
Page 133 and 134: 14.4.1 Start commandThe parameters
Page 135 and 136: 14.4.8 Fixed Value Change-OverDepen
Page 137 and 138: 14.5.1.1 Time ConstantThe logic seq
Page 139 and 140: The switch-on and switch-off thresh
Page 141 and 142: Examples of the logic functions dep
Page 143 and 144:
Parameter Operation Mode Logic = 30
Page 145 and 146:
The default Cut-Off Voltage 603 (UC
Page 147 and 148:
16.2 Voltage controllerThe voltage
Page 149 and 150:
ParameterSettingsNo. Description Mi
Page 151 and 152:
16.3 Technology ControllerThe techn
Page 153 and 154:
Structural image:Technology control
Page 155 and 156:
Behavior in generator operation:If
Page 157 and 158:
16.5.2.1 Limit Value SourcesThe lim
Page 159 and 160:
−−−The output value of the co
Page 161 and 162:
Optimization of the controller para
Page 163 and 164:
17 Special FunctionsThe configurabl
Page 165 and 166:
Operation modeFunctionControl via K
Page 167 and 168:
17.4.1 Dimensioning of Brake Resist
Page 169 and 170:
Multiple motor operationParameter O
Page 171 and 172:
17.7.2 Temperature AdjustmentThe fi
Page 173 and 174:
18 Actual ValuesThe various control
Page 175 and 176:
18.3 Actual Value MemoryThe assessm
Page 177 and 178:
18.4.2 Volume Flow and PressureThe
Page 179 and 180:
InsideCodeMeaningF0300 Inside tempe
Page 181 and 182:
Error Environment357 Int. Value 1 S
Page 183 and 184:
A decimal value is displayed, indic
Page 185 and 186:
21 Parameter ListThe parameter list
Page 187 and 188:
Error EnvironmentNo. Description Un
Page 189 and 190:
Controlled commissioningNo. Descrip
Page 191 and 192:
Fixed FrequenciesNo. Description Un
Page 193 and 194:
Search RunNo. Description Unit Sett
Page 195 and 196:
INDUSTRY PROCESSAND AUTOMATION SOLU
show all

Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

Create successful ePaper yourself

Delete template?

Save as template?