Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

More documents

Recommendations

Info

5.5.2 Frequency Inverter (5.5 up to 15.0 kW)Connection of brake resistor with temperature switchX2UVWRb1 Rb2X25.5 kW … 9.2 kWWAGO Serie 745 / 6qmm / RM7,520.2 … 6 mmAWG 24 … 1020.2 … 6 mmAWG 24 … 1020.25 … 4 mmAWG 22 … 1220.25 … 4 mmAWG 22 … 16Rb1T1R bRb2T211.0 kW … 15.0 kWWAGO Serie 745 / 16qmm / RM10+1520.2 … 16 mmAWG 24 … 620.2 … 16 mmAWG 24 … 620.25 … 10 mmAWG 22 … 820.25 … 10 mmAWG 22 … 85.5.3 Frequency Inverter (18.5 up to 30.0 kW)Connection of brake resistor with temperature switchX2UVWRb1 Rb2X2Rb1R bRb218.5 kW … 30 kWPHOENIX MKDSP 25/ 6-15,00-F20.5 … 35 mmAWG 20 … 220.5 … 25 mmAWG 20 … 421.00 … 25 mmAWG 18 … 421.5 … 25 mmAWG 16 … 42.5 Nm22.1 lb-inT1T240 02/06
5.5.4 Frequency Inverter (37.0 up to 65.0 kW)Connection of brake resistor with temperature switchX2UVWRb1 Rb2X237.0 kW … 65.0 kWthreaded bolt M8x25Wire cross section up to 70 mm 28 Nm70.8 lb-inRb1T1R bRb2T202/06 41
Page 1: INDUSTRYPROCESSAND AUTOMATION SOLUT
Page 4 and 5: TABLE OF CONTENTS1. General Safety
Page 6 and 7: TABLE OF CONTENTS7 Commissioning of
Page 8 and 9: TABLE OF CONTENTS13.10 Motor Potent
Page 10 and 11: TABLE OF CONTENTS19 Error Protocol.
Page 12 and 13: 1.2 Purpose of the Frequency Invert
Page 14 and 15: 2 Scope of SupplyThanks to the modu
Page 16 and 17: 2.3 Frequency Inverter (18.5 up to
Page 18 and 19: 3 Technical Data3.1 Frequency Inver
Page 20 and 21: 3.3 Frequency Inverter 400 V (5.5 u
Page 22 and 23: 3.5 Frequency Inverter 400 V (37.0
Page 24 and 25: 4 Mechanical InstallationThe freque
Page 26 and 27: 4.2 Frequency Inverter (5.5 to 15.0
Page 28 and 29: 4.4 Frequency inverter (37.0 up to
Page 30 and 31: 5.1 EMC InformationThe frequency in
Page 32 and 33: 5.3 Mains ConnectionThe mains fuses
Page 34 and 35: 5.3.3 Frequency Inverter (18.5 up t
Page 36 and 37: 5.4 Motor ConnectionThe connection
Page 38 and 39: 5.4.2 Frequency Inverter (5.5 up to
Page 40 and 41: 5.4.4 Frequency Inverter (37.0 up t
Page 44 and 45: 5.6 Control TerminalsThe control an
Page 46 and 47: 5.6.2 Control Terminals - Terminal
Page 48 and 49: 5.6.2.4 Configuration 411 - Sensorl
Page 50 and 51: 5.7 Optional ComponentsThanks to th
Page 54 and 55: 6.4 Parameter Menu (PARA)The parame
Page 56 and 57: Function - ActOnly the active param
Page 58 and 59: 6.5.6 Error MessagesThe copy functi
Page 60 and 61: Activation via CM Communication Mod
Page 62 and 63: 6.8 Controlling the Motor via the C
Page 64 and 65: 7 Commissioning of the Frequency In
Page 66 and 67: 7.2.2 Data SetThe data set change-o
Page 68 and 69: 101 -104 -Operation modeSingle eval
Page 70 and 71: Warning!Switch off power supply bef
Page 72 and 73: 7.2.8.2 Set points at multi-functio
Page 74 and 75: Operation mode24 - Check Machine Da
Page 76 and 77: 8.3 Inverter Software VersionThe fi
Page 78 and 79: In the table, you will find a list
Page 80 and 81: 9 Machine DataThe input of the mach
Page 82 and 83: 9.2.4 Rated Slip Correction FactorT
Page 84 and 85: 10 System DataThe various control f
Page 86 and 87: Operation mode3 -4 -12 -14 -Magneti
Page 88 and 89: 11.2 Stopping BehaviorThe stopping
Page 90 and 91: 11.2.1 Switch-Off ThresholdThe Swit
Page 92 and 93:
11.5 Search RunThe synchronization
Page 94:
11.6.1 Reference PositioningThe fee
Page 97 and 98:
11.6.2 Axis PositioningFor axis pos
Page 99 and 100:
12 Error and warning behaviorOperat
Page 101 and 102:
12.6 Motor TemperatureThe configura
Page 103 and 104:
13 Reference ValuesThe ACT series f
Page 105 and 106:
13.4.1 Block DiagramThe following t
Page 107 and 108:
13.5 Reference Percentage ChannelTh
Page 109 and 110:
13.6 Fixed Reference ValuesThe fixe
Page 111 and 112:
The ramps for Emergency Stop Clockw
Page 113 and 114:
13.8 Percentage Value RampsThe perc
Page 115 and 116:
The Operation Mode 474 of the motor
Page 117 and 118:
13.11 Repetition frequency inputThe
Page 119 and 120:
The following characteristic is set
Page 121 and 122:
The default Minimum Frequency 418 o
Page 123 and 124:
14.2.1 Analog Output MFO1ABy defaul
Page 125 and 126:
14.3 Digital OutputsThe OP. Mode Di
Page 127 and 128:
14.3.4 Open brakeThe Open brake fun
Page 129 and 130:
Operation modeFunctionThe DC link v
Page 131 and 132:
Operation modeFunction158 - Timer 1
Page 133 and 134:
14.4.1 Start commandThe parameters
Page 135 and 136:
14.4.8 Fixed Value Change-OverDepen
Page 137 and 138:
14.5.1.1 Time ConstantThe logic seq
Page 139 and 140:
The switch-on and switch-off thresh
Page 141 and 142:
Examples of the logic functions dep
Page 143 and 144:
Parameter Operation Mode Logic = 30
Page 145 and 146:
The default Cut-Off Voltage 603 (UC
Page 147 and 148:
16.2 Voltage controllerThe voltage
Page 149 and 150:
ParameterSettingsNo. Description Mi
Page 151 and 152:
16.3 Technology ControllerThe techn
Page 153 and 154:
Structural image:Technology control
Page 155 and 156:
Behavior in generator operation:If
Page 157 and 158:
16.5.2.1 Limit Value SourcesThe lim
Page 159 and 160:
−−−The output value of the co
Page 161 and 162:
Optimization of the controller para
Page 163 and 164:
17 Special FunctionsThe configurabl
Page 165 and 166:
Operation modeFunctionControl via K
Page 167 and 168:
17.4.1 Dimensioning of Brake Resist
Page 169 and 170:
Multiple motor operationParameter O
Page 171 and 172:
17.7.2 Temperature AdjustmentThe fi
Page 173 and 174:
18 Actual ValuesThe various control
Page 175 and 176:
18.3 Actual Value MemoryThe assessm
Page 177 and 178:
18.4.2 Volume Flow and PressureThe
Page 179 and 180:
InsideCodeMeaningF0300 Inside tempe
Page 181 and 182:
Error Environment357 Int. Value 1 S
Page 183 and 184:
A decimal value is displayed, indic
Page 185 and 186:
21 Parameter ListThe parameter list
Page 187 and 188:
Error EnvironmentNo. Description Un
Page 189 and 190:
Controlled commissioningNo. Descrip
Page 191 and 192:
Fixed FrequenciesNo. Description Un
Page 193 and 194:
Search RunNo. Description Unit Sett
Page 195 and 196:
INDUSTRY PROCESSAND AUTOMATION SOLU
show all

Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?