Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

More documents

Recommendations

Info

19 Error ProtocolThe various control methods and the hardware of the frequency inverter include functionswhich continuously monitor the application. The operational and error diagnosisis facilitated by the information stored in the error protocol.19.1 Error ListThe last 16 fault messages are stored in chronological order and the No. of Errors362 shows the number of errors which have occurred since commissioning of thefrequency inverter. In the VAL menu branch of the control unit, the error code FXXXXis displayed. The meaning of the error key is described in the following chapter "ErrorMessages". Via the PC program, the number of operation hours (h), operation minutes(m) and the fault message can additionally be read out. The current operating hourscan be read out via the Operation Hours Counter 245. The fault report can be acknowledgedvia the keys of the operating unit and according to the assignment ErrorAcknowledgment 103.Error ListNo. Description Function310 Last Error hhhhh:mm ; FXXXX fault message311 Last Error but one hhhhh:mm ; FXXXX fault message312 to 325 error 3 to error 16362 No. of errors occurredNumber of errors occurred after commissioningof the frequency inverterThe error and warning behavior of the frequency inverter can be set in various ways.The automatic error acknowledgment enables acknowledgment of the faults OvercurrentF0500, Overcurrent F0507 and Overvoltage F0700 without intervention by anoverriding control system or the user. The No. of self acknowledged Errors 363shows the total number of automatic error acknowledgments.Error ListNo. Description Function363 No. of acknowledgmentErrorsTotal number of automatic error acknowledgmentwith synchronization19.1.1 Error MessagesThe error code stored following a fault comprises the error group FXX and the followingcode number XX.Error MessagesCodeMeaningF00 00 No fault has occurred.OverloadF01 00 <strong>Frequency</strong> inverter overloadedF0102 <strong>Frequency</strong> inverter overloaded (60 s), check load behavior03 Short-term overload (1 s), check motor and application parametersHeat SinkF0200 Heat sink temperature too high, check cooling and fan01 Temperature sensor defective or ambient temperature too lowTable "Error Messages" continued on next page.176 02/06
InsideCodeMeaningF0300 Inside temperature too high, check cooling and fan01 Inside temperature too low, check electrical cabinet heatingMotor Connection00Motor temperature too high or sensor defective, check connectionS6INDF04 01 Motor circuit breaker tripped, check drive02 V-belt monitoring reports no load on the drive.03 Phase failure, check motor and wiringOutput current00 Overloaded, check load situation and ramps03 Short circuit or earth fault, check motor and wiringF0504 Overloaded, check load situation and current value limit controller05 Asymmetric motor current, check current and wiring06 Motor phase current too high, check motor and wiring07 Message from phase monitoring, check motor and wiringDC link voltage00DC link voltage too high, check deceleration ramps and connected brakeresistor01 DC link voltage too low, check mains voltageF0702 Power failure, check mains voltage and circuit03 Phase failure, check mains fuses and circuit04 Reference DC-Link Limitation 680 too low, check mains voltage05 Brake chopper Trigger Threshold 506 too low, check mains voltage06 Motor chopper Trigger Threshold 507 too low, check mains voltageElectronics voltageF0801 Electronics voltage 24 V too low, check control terminal04 Electronics voltage too high, check wiring of control terminalsOutput frequency00 Output frequency too high, check control signals and settingsF11 Max. frequency reached by control, check deceleration ramps and connectedbrake resistor01Motor Connection00 Earth fault on output, check motor and wiringF13 01Set IDC-Compensation Limit 415 reached, check motor and cabling,increase limit, if necessary10 Minimum current monitoring, check motor and wiringControl Connection01 Reference value on multifunctional input 1 faulty, check signal07 Overcurrent on multifunctional input 1, check signalF14 30 Speed sensor signal defective, check connections S4IND and S5IND31 One track of the speed sensor signal is missing, check connections32 Direction of rotation of speed sensor wrong, check connectionsOptional ComponentsF0A 10Data transmission from control unit KP 500 to inverter failed. In thecontrol unit must be stored at least 1 file.F0B 13The communication module was fitted to slot B without disconnection ofthe mains voltage, switch mains voltage off.In addition to fault messages mentioned, there are further fault messages. Howeverthese messages are only used for internal purposes and are not listed here. If youreceive fault messages which are not listed here, please contact us by phone.02/06 177
Page 1:
INDUSTRYPROCESSAND AUTOMATION SOLUT
Page 4 and 5:
TABLE OF CONTENTS1. General Safety
Page 6 and 7:
TABLE OF CONTENTS7 Commissioning of
Page 8 and 9:
TABLE OF CONTENTS13.10 Motor Potent
Page 10 and 11:
TABLE OF CONTENTS19 Error Protocol.
Page 12 and 13:
1.2 Purpose of the Frequency Invert
Page 14 and 15:
2 Scope of SupplyThanks to the modu
Page 16 and 17:
2.3 Frequency Inverter (18.5 up to
Page 18 and 19:
3 Technical Data3.1 Frequency Inver
Page 20 and 21:
3.3 Frequency Inverter 400 V (5.5 u
Page 22 and 23:
3.5 Frequency Inverter 400 V (37.0
Page 24 and 25:
4 Mechanical InstallationThe freque
Page 26 and 27:
4.2 Frequency Inverter (5.5 to 15.0
Page 28 and 29:
4.4 Frequency inverter (37.0 up to
Page 30 and 31:
5.1 EMC InformationThe frequency in
Page 32 and 33:
5.3 Mains ConnectionThe mains fuses
Page 34 and 35:
5.3.3 Frequency Inverter (18.5 up t
Page 36 and 37:
5.4 Motor ConnectionThe connection
Page 38 and 39:
5.4.2 Frequency Inverter (5.5 up to
Page 40 and 41:
5.4.4 Frequency Inverter (37.0 up t
Page 42 and 43:
5.5.2 Frequency Inverter (5.5 up to
Page 44 and 45:
5.6 Control TerminalsThe control an
Page 46 and 47:
5.6.2 Control Terminals - Terminal
Page 48 and 49:
5.6.2.4 Configuration 411 - Sensorl
Page 50 and 51:
5.7 Optional ComponentsThanks to th
Page 54 and 55:
6.4 Parameter Menu (PARA)The parame
Page 56 and 57:
Function - ActOnly the active param
Page 58 and 59:
6.5.6 Error MessagesThe copy functi
Page 60 and 61:
Activation via CM Communication Mod
Page 62 and 63:
6.8 Controlling the Motor via the C
Page 64 and 65:
7 Commissioning of the Frequency In
Page 66 and 67:
7.2.2 Data SetThe data set change-o
Page 68 and 69:
101 -104 -Operation modeSingle eval
Page 70 and 71:
Warning!Switch off power supply bef
Page 72 and 73:
7.2.8.2 Set points at multi-functio
Page 74 and 75:
Operation mode24 - Check Machine Da
Page 76 and 77:
8.3 Inverter Software VersionThe fi
Page 78 and 79:
In the table, you will find a list
Page 80 and 81:
9 Machine DataThe input of the mach
Page 82 and 83:
9.2.4 Rated Slip Correction FactorT
Page 84 and 85:
10 System DataThe various control f
Page 86 and 87:
Operation mode3 -4 -12 -14 -Magneti
Page 88 and 89:
11.2 Stopping BehaviorThe stopping
Page 90 and 91:
11.2.1 Switch-Off ThresholdThe Swit
Page 92 and 93:
11.5 Search RunThe synchronization
Page 94:
11.6.1 Reference PositioningThe fee
Page 97 and 98:
11.6.2 Axis PositioningFor axis pos
Page 99 and 100:
12 Error and warning behaviorOperat
Page 101 and 102:
12.6 Motor TemperatureThe configura
Page 103 and 104:
13 Reference ValuesThe ACT series f
Page 105 and 106:
13.4.1 Block DiagramThe following t
Page 107 and 108:
13.5 Reference Percentage ChannelTh
Page 109 and 110:
13.6 Fixed Reference ValuesThe fixe
Page 111 and 112:
The ramps for Emergency Stop Clockw
Page 113 and 114:
13.8 Percentage Value RampsThe perc
Page 115 and 116:
The Operation Mode 474 of the motor
Page 117 and 118:
13.11 Repetition frequency inputThe
Page 119 and 120:
The following characteristic is set
Page 121 and 122:
The default Minimum Frequency 418 o
Page 123 and 124:
14.2.1 Analog Output MFO1ABy defaul
Page 125 and 126:
14.3 Digital OutputsThe OP. Mode Di
Page 127 and 128: 14.3.4 Open brakeThe Open brake fun
Page 129 and 130: Operation modeFunctionThe DC link v
Page 131 and 132: Operation modeFunction158 - Timer 1
Page 133 and 134: 14.4.1 Start commandThe parameters
Page 135 and 136: 14.4.8 Fixed Value Change-OverDepen
Page 137 and 138: 14.5.1.1 Time ConstantThe logic seq
Page 139 and 140: The switch-on and switch-off thresh
Page 141 and 142: Examples of the logic functions dep
Page 143 and 144: Parameter Operation Mode Logic = 30
Page 145 and 146: The default Cut-Off Voltage 603 (UC
Page 147 and 148: 16.2 Voltage controllerThe voltage
Page 149 and 150: ParameterSettingsNo. Description Mi
Page 151 and 152: 16.3 Technology ControllerThe techn
Page 153 and 154: Structural image:Technology control
Page 155 and 156: Behavior in generator operation:If
Page 157 and 158: 16.5.2.1 Limit Value SourcesThe lim
Page 159 and 160: −−−The output value of the co
Page 161 and 162: Optimization of the controller para
Page 163 and 164: 17 Special FunctionsThe configurabl
Page 165 and 166: Operation modeFunctionControl via K
Page 167 and 168: 17.4.1 Dimensioning of Brake Resist
Page 169 and 170: Multiple motor operationParameter O
Page 171 and 172: 17.7.2 Temperature AdjustmentThe fi
Page 173 and 174: 18 Actual ValuesThe various control
Page 175 and 176: 18.3 Actual Value MemoryThe assessm
Page 177: 18.4.2 Volume Flow and PressureThe
Page 181 and 182: Error Environment357 Int. Value 1 S
Page 183 and 184: A decimal value is displayed, indic
Page 185 and 186: 21 Parameter ListThe parameter list
Page 187 and 188: Error EnvironmentNo. Description Un
Page 189 and 190: Controlled commissioningNo. Descrip
Page 191 and 192: Fixed FrequenciesNo. Description Un
Page 193 and 194: Search RunNo. Description Unit Sett
Page 195 and 196: INDUSTRY PROCESSAND AUTOMATION SOLU
show all

Operating Instruction - Frequency Inverter 230V / 400V ... - opis.cz

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?