Sepam - HV/MV Protection and control units (ENG) - Trinet

Data addresses and encoding (cont’d)Control logic zone (cont’d)control logic word bit access Jbus function format unit as ofzone address address enabled versionremote controlKTC1-16 (latched KTC) 0C80 C800- C80F read/write 1, 3, 5, 6, 15, 16 E noneKTC17-32 (latched KTC) 0C81 C810- C81F read/write 1, 3, 5, 6, 15, 16 E nonereserved 0C82-0C87 init. to 0KTC33-48 (impulse KTC) 0C88 C880- C88F read/write 1, 3, 5, 6, 15, 16 E noneKTC49-64 (impulse KTC) 0C89 C890- C89F read/write 1, 3, 5, 6, 15, 16 E noneKTC65-KTC80 (impulse KTC) 0C8A C8A0-C8AF read/write 1, 3, 5, 6, 15, 16 E none 3.1KTC81-KTC96 (impulse KTC) 0C8B C8B0-C8BF read/write 1, 3, 5, 6, 15, 16 E none 3.1remote annunciationreserved 0C8C C8C0- C8CF read 1, 3 init. to 0reserved 0C8D C8D0- C8DF read 1, 3 init. to 0reserved 0C8E C8E0- C8EF read 1, 3 init. to 0Sepam check 0C8F C8F0- C8FF read 1, 3, 7(b15-b8) (1) X noneKTS1-KTS16 0C90 C900- C90F read 1, 3 E noneKTS17-KTS32 0C91 C910- C91F read 1, 3 E noneKTS33-KTS48 0C92 C920-C92F read 1, 3 E none 3.1KTS49-KTS64 0C93 C930-C93F read 1, 3 E none 3.1reserved 0C94 C940-C94F read 1, 3 init. to 0reserved 0C95 read 3 init. to 0reserved 0C96 read 3 init. to 0reserved 0C97 read 3 init. to 0KTS1-KTS16 (oscill. status) 0C98 C980- C98F read 1, 3 E noneKTS17-KTS32 (oscill. status) 0C99 C990- C99F read 1, 3 E noneKTS33-KTS48 (oscill. status) 0C9A C9A0-C9AF read 1, 3 E none 3.1KTS49-KTS64 (oscill. status) 0C9B C9B0-C9BF read 1, 3 E none 3.1reserved 0C9C-0C9F C9C0-C9FF read 1, 3 init. to 0event countersC1 0C40 read 3 A noneC2 0C41 read 3 A noneC3 0C42 read 3 A noneC4 0C43 read 3 A noneC5 0C44 read 3 A noneC6 0C45 read 3 A noneC7 0C46 read 3 A noneC8 0C47 read 3 A noneC9 0C48 read 3 A noneC10 0C49 read 3 A noneC11 0C4A read 3 A noneC12 0C4B read 3 A noneC13 0C4C read 3 A noneC14 0C4D read 3 A noneC15 0C4E read 3 A noneC16 0C4F read 3 A noneC17 0C50 read 3 A none 3.1C18 0C51 read 3 A none 3.1C19 0C52 read 3 A none 3.1C20 0C53 read 3 A none 3.1C21 0C54 read 3 A none 3.1C22 0C55 read 3 A none 3.1C23 0C56 read 3 A none 3.1C24 0C57 read 3 A none 3.1(1)Jbus/Modbus function n° 7 “high-speed 8 bit reading” can be used to read the value of the most significant byte of the “Sepam check” word, with Jbus address0C8F (refer to the appendix which describes Jbus protocol).10 Jbus/Modbus communication