Junos® OS Ethernet Interfaces Configuration ... - Juniper Networks

More documents

Recommendations

Info

Junos ® OS 12.3 Ethernet Interfaces Configuration Guide Action • To display CFM database information (including ETH-DM frame counts) for all MEPs in MA ma1 within MD md1: user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain ma1 maintenance-association ma1 • To display CFM database information (including ETH-DM frame counts) only for local MEP 201 in MA ma1 within MD md1: user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain md2 maintenance-association ma2 local-mep 201 • To display CFM database information (including ETH-DM frame counts) only for remote MEP 302 in MD md3 within MA ma3: user@host> show oam ethernet connectivity-fault-management mep-database maintenance-domain ma3 maintenance-association ma3 remote-mep 302 Displaying ETH-DM Frame Counts for MEPs by Interface or Domain Level Purpose Display ETH-DM frame counts for CFM maintenance association end points (MEPs). By default, the show oam ethernet connectivity-fault-management interfaces command displays CFM database information for MEPs attached to CFM-enabled Ethernet interfaces on the router or at a maintenance domain level. For Ethernet interfaces that support ETH-DM, any frame counts are also displayed when you specify the detail or extensive command option. NOTE: At the router attached to the initiator MEP for a one-way session, or at the router attached to the receiver MEP for a two-way session, you can only display ETH-DM frame counts. Action • To display CFM database information (including ETH-DM frame counts) for all MEPs attached to CFM-enabled Ethernet interfaces on the router: user@host> show oam ethernet connectivity-fault-management interfaces detail • To display CFM database information (including ETH-DM frame counts) only for the MEPs attached to CFM-enabled router interface ge-5/2/9.0: user@host> show oam ethernet connectivity-fault-management interfaces ge-5/2/9.0 detail • To display CFM database information (including ETH-DM frame counts) only for MEPs Clearing ETH-DM Statistics and Frame Counts 268 enclosed within CFM maintenance domains (MDs) at level 6: user@host> show oam ethernet connectivity-fault-management interfaces level 6 detail Purpose Clear the ETH-DM statistics and ETH-DM frame counts. By default, statistics and frame counts are deleted for all MEPs attached to CFM-enabled interfaces on the router. However, you can filter the scope of the command by specifying an interface name. Copyright © 2012, Juniper Networks, Inc.
Action • To clear the ETH-DM statistics and ETH-DM frame counts for all MEPs attached to Related Documentation CFM-enabled interfaces on the router: user@host> clear oam ethernet connectivity-fault-management statistics • To clear the ETH-DM statistics and ETH-DM frame counts only for MEPs attached to • the logical interface ge-0/5.9.0: user@host> clear oam ethernet connectivity-fault-management statistics ge-0/5/9.0 clear oam ethernet connectivity-fault-management statistic command • show oam ethernet connectivity-fault-management delay-statistics command • show oam ethernet connectivity-fault-management interfaces (detail | extensive) command Managing ETH-LM Statistics Displaying ETH-LM Statistics • show oam ethernet connectivity-fault-management mep-statistics command • show oam ethernet connectivity-fault-management mep-database command • Junos® OS Ethernet Interfaces • Displaying ETH-LM Statistics on page 269 • Clearing ETH-LM Statistics on page 270 Purpose Display the ETH-LM statistics. By default, the show oam ethernet connectivity-fault-management loss-statistics maintenance-domain md-name maintenance-association ma-name command displays ETH-LM statistics for MEPs in the specified CFM maintenance association (MA) within the specified CFM maintenance domain (MD). The following list consists of the CFM-related operational mode commands that have been enhanced to display ETH-LM statistics: • The show oam ethernet connectivity-fault-management interfaces detail command is enhanced to display ETH-DM and ETH-LM statistics for MEPs in the specified CFM maintenance association (MA) within the specified CFM maintenance domain (MD). • The show oam ethernet connectivity-fault-management mep-statistics command is enhanced to display ETH-DM and ETH-LM statistics and frame counts for MEPs in the specified CFM maintenance association (MA) within the specified CFM maintenance domain (MD). • The show oam ethernet connectivity-fault-management mep-database command is enhanced to display ETH-DM and ETH-LM frame counters for MEPs in the specified CFM maintenance association (MA) within the specified CFM maintenance domain (MD). Copyright © 2012, Juniper Networks, Inc. Chapter 14: Configuring ITU-T Y.1731 Ethernet Service OAM 269
Page 1 and 2:
Junos ® OS Ethernet Interfaces Con
Page 3 and 4:
Abbreviated Table of Contents About
Page 5 and 6:
Table of Contents About This Guide
Page 7 and 8:
Configuring Extended VLAN Encapsula
Page 9 and 10:
Configuring LACP System Identifier
Page 11 and 12:
Copyright © 2012, Juniper Networks
Page 13 and 14:
ETH-DM Frame Count Retrieval . . .
Page 15 and 16:
Chapter 20 Configuring Gigabit Ethe
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
static-interface . . . . . . . . .
Page 23 and 24:
List of Figures Part 2 Configuring
Page 25 and 26:
List of Tables About This Guide . .
Page 27 and 28:
About This Guide This preface provi
Page 29 and 30:
Using the Indexes • MX Series •
Page 31 and 32:
Table 1: Notice Icons Icon Meaning
Page 33 and 34:
or are covered under warranty, and
Page 35 and 36:
PART 1 Ethernet Interfaces Configur
Page 37 and 38:
CHAPTER 1 Ethernet Interfaces Confi
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Related Documentation • primary;
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Related Documentation • Junos OS
Page 61 and 62:
Page 63 and 64:
Related Documentation • Junos OS
Page 65 and 66:
Related Documentation Copyright ©
Page 67 and 68:
PART 2 Configuring Ethernet Interfa
Page 69 and 70:
CHAPTER 2 Configuring Ethernet Inte
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Routed traffic is forwarded from an
Page 77 and 78:
To enable the filtering, include th
Page 79 and 80:
Configuring Ethernet Loopback Capab
Page 81 and 82:
By default, the router’s manageme
Page 83 and 84:
Adjusting the ARP Aging Timer Relat
Page 85 and 86:
Configuring Multicast Statistics Co
Page 87 and 88:
CHAPTER 3 Configuring 802.1Q VLANs
Page 89 and 90:
Related Documentation Dynamically c
Page 91 and 92:
Configuring Single-Tag Framing Conf
Page 93 and 94:
family inet { address 10.66.1.2/30;
Page 95 and 96:
• [edit logical-systems logical-s
Page 97 and 98:
Page 99 and 100:
Associating a VLAN ID to a VLAN Dem
Page 101 and 102:
Related Documentation • 802.1Q VL
Page 103 and 104:
Guidelines for Configuring Logical
Page 105 and 106:
Specifying the Interface to Handle
Page 107 and 108:
Example: Configuring a Layer 2 VPN
Page 109 and 110:
Related Documentation family mpls;
Page 111 and 112:
Configuring the VLAN ID List for a
Page 113 and 114:
Page 115 and 116:
CHAPTER 4 Configuring Aggregated Et
Page 117 and 118:
Related Documentation Use the show
Page 119 and 120:
• Enabling LACP Link Protection o
Page 121 and 122:
Configuring the Maximum Links Limit
Page 123 and 124:
Related Documentation status-contro
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Layer 3 Routing • MAC addresses l
Page 131 and 132:
Figure 9: Multicast Topology with S
Page 133 and 134:
Configuring MC-LAG Configuring Inte
Page 135 and 136:
} } Logical Systems logical-system
Page 137 and 138:
Related Documentation In this examp
Page 139 and 140:
Typically Supported Network Topolog
Page 141 and 142:
Pure Layer 2 Topology Without Integ
Page 143 and 144:
Related Documentation • IGMP snoo
Page 145 and 146:
• Reverting Traffic to a Primary
Page 147 and 148:
LACP is defined in IEEE 802.3ad, Ag
Page 149 and 150:
LACP link protection also uses port
Page 151 and 152:
Tracing LACP Operations Copyright
Page 153 and 154:
LACP with Untagged Aggregated Ether
Page 155 and 156:
Related Documentation • } } For m
Page 157 and 158:
Related Documentation The multicast
Page 159 and 160:
Configuring Symmetric Load Balancin
Page 161 and 162:
Page 163 and 164:
CHAPTER 5 Stacking and Rewriting Gi
Page 165 and 166:
• push—Add a new VLAN tag to th
Page 167 and 168:
Table 9: Applying Rewrite Operation
Page 169 and 170:
Related Documentation • unit on p
Page 171 and 172:
Table 10: Rewrite Operations and St
Page 173 and 174:
Related Documentation Removing a VL
Page 175 and 176:
Related Documentation • [edit log
Page 177 and 178:
• For more information about bind
Page 179 and 180:
Example: push-push and pop-pop with
Page 181 and 182:
Related Documentation swap-swap; Yo
Page 183 and 184:
Swap a VLAN ID on Ingress Swap a VL
Page 185 and 186:
Swap the Outer VLAN Tag and Push a
Page 187 and 188:
Pop an Outer VLAN Tag to Connect an
Page 189 and 190:
CHAPTER 6 Configuring Layer 2 Bridg
Page 191 and 192:
CHAPTER 7 Configuring Link Layer Di
Page 193 and 194:
Page 195 and 196:
Related Documentation You can speci
Page 197 and 198:
CHAPTER 8 Configuring TCC and Layer
Page 199 and 200:
Configuring Ethernet TCC • Config
Page 201 and 202:
CHAPTER 9 Configuring Static ARP Ta
Page 203 and 204:
CHAPTER 10 Configuring Restricted a
Page 205 and 206:
Related Documentation Figure 17: Co
Page 207 and 208:
CHAPTER 11 Configuring MAC Address
Page 209 and 210:
Page 211 and 212:
CHAPTER 12 Enabling Passive Monitor
Page 213 and 214:
Related Documentation • Junos® O
Page 215 and 216:
CHAPTER 13 Configuring IEEE 802.1ag
Page 217 and 218:
Page 219 and 220:
Related Documentation • connectiv
Page 221 and 222:
Related Documentation all maintenan
Page 223 and 224:
• interval time • loss-threshol
Page 225 and 226:
Configuring a Maintenance Endpoint
Page 227 and 228:
Table 15: Lowest Priority Defect Op
Page 229 and 230:
Page 231 and 232:
Configuring a CFM Action Profile Ev
Page 233 and 234:
Configuring Linktrace Protocol in C
Page 235 and 236:
Page 237 and 238:
Example E-LMI Configuration Copyrig
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Table 18: Type Field Values for Var
Page 245 and 246:
For configuration information, see
Page 247 and 248:
Interface: ge-2/0/0.0 Last flapped:
Page 249 and 250:
Page 251 and 252: Identifier MAC address State Interf
Page 253 and 254: Related Documentation Copyright ©
Page 255 and 256: Figure 22: CET inter-op Dual Homed
Page 257 and 258: • IEEE 802.1ag OAM Connectivity F
Page 259 and 260: • Configuring Maintenance Interme
Page 263 and 264: Related Documentation • connectiv
Page 265 and 266: Copyright © 2012, Juniper Networks
Page 269 and 270: [edit protocols oam] ethernet { con
Page 271 and 272: CHAPTER 14 Configuring ITU-T Y.1731
Page 273 and 274: ITU-T Y.1731 Frame Delay Measuremen
Page 277 and 278: Two-Way ETH-DM Frame Counts Each ro
Page 279 and 280: Related Documentation On-Demand Mod
Page 281 and 282: The Y.1731 frame transmission for a
Page 283 and 284: Configuring an Iterator Profile Cop
Page 287 and 288: Guidelines for Configuring Routers
Page 289 and 290: • CFM maintenance association—N
Page 291 and 292: Table 24: ETH-DM Statistics Field N
Page 293 and 294: Table 25: ETH-DM Frame Counts (cont
Page 295 and 296: Ensuring That Distributed ppm Is No
Page 297 and 298: 2. Modify the router configuration
Page 299 and 300: Starting a One-Way ETH-DM Session
Page 301: Action • To display the ETH-DM st
Page 305 and 306: user@host> show oam ethernet connec
Page 307 and 308: Table 26: Displaying Iterator Stati
Page 309 and 310: Clearing Iterator Statistics Purpos
Page 317 and 318: Related Documentation • Valid in-
Page 319 and 320: [edit protocols oam ethernet connec
Page 321 and 322: CHAPTER 15 Configuring IEEE 802.1x
Page 323 and 324: Related Documentation Configuring t
Page 325 and 326: CHAPTER 16 Configuring IEEE 802.3ah
Page 327 and 328: Configuring IEEE 802.3ah OAM Link-F
Page 329 and 330: Related Documentation You can speci
Page 331 and 332: • IEEE 802.3ah OAM Link-Fault Man
Page 333 and 334: Detecting Remote Faults Related Doc
Page 335 and 336: • Enabling IEEE 802.3ah OAM Suppo
Page 337 and 338: Monitoring the Loss of Link Adjacen
Page 339 and 340: Configuring Threshold Values for Fa
Page 341 and 342: Related Documentation except OAM PD
Page 345 and 346: CHAPTER 17 Configuring VRRP and VRR
Page 347 and 348: Related Documentation To configure
Page 349 and 350: CHAPTER 18 Configuring Gigabit Ethe
Page 351 and 352: Related Documentation For more info
Page 353 and 354:
Specifying an Output Priority Map [
Page 355 and 356:
NOTE: If the remote Ethernet card i
Page 357 and 358:
Related Documentation • bandwidth
Page 359 and 360:
Applying a Policer excess-burst-siz
Page 361 and 362:
Page 363 and 364:
CHAPTER 19 Configuring Gigabit Ethe
Page 365 and 366:
Displaying Autonegotiation Status T
Page 367 and 368:
Table 30: Mode and Autonegotiation
Page 369 and 370:
CHAPTER 20 Configuring Gigabit Ethe
Page 371 and 372:
CHAPTER 21 Configuring the Manageme
Page 373 and 374:
Related Documentation } } This feat
Page 375 and 376:
CHAPTER 22 Configuring 10-Gigabit E
Page 377 and 378:
Page 379 and 380:
• Configuring Control Queue Disab
Page 381 and 382:
Forwarding Untagged Layer2 Control
Page 383 and 384:
Example: Handling Oversubscription
Page 385 and 386:
Capability • vlan-ccc—802.1Q ta
Page 387 and 388:
CHAPTER 23 Configuring the 10-Gigab
Page 389 and 390:
Page 391 and 392:
Understanding WAN Framing for 10-Gi
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
CHAPTER 27 Configuring 100-Gigabit
Page 399 and 400:
Related Documentation MPC3E MIC Ove
Page 401 and 402:
• 2-port 10-Gigabit Ethernet MICs
Page 403 and 404:
To configure a 100-Gigabit Ethernet
Page 405 and 406:
• VLAN rules describe how the rou
Page 407 and 408:
• You cannot include the vlan-id
Page 409 and 410:
Related Documentation forwards the
Page 411 and 412:
Page 413 and 414:
Page 415 and 416:
Configuring 40-Gigabit Ethernet PIC
Page 417 and 418:
CHAPTER 29 Configuring Ethernet Int
Page 419 and 420:
Configuring MAC Filtering on PTX Se
Page 421 and 422:
Related Documentation As a conseque
Page 423 and 424:
Related Documentation On PTX Series
Page 425 and 426:
Configuring Aggregated Ethernet Int
Page 427 and 428:
CHAPTER 30 Configuring Point-to-Poi
Page 429 and 430:
PPPoE Stages Copyright © 2012, Jun
Page 431 and 432:
Page 433 and 434:
the name of the AC from which it wa
Page 435 and 436:
You can also associate a PPPoE dyna
Page 437 and 438:
Evaluation Order for Matching Clien
Page 439 and 440:
6. Optionally, specify how many sec
Page 441 and 442:
Configuring a PPPoE Interface Copyr
Page 443 and 444:
• [edit logical-systems logical-s
Page 445 and 446:
Page 447 and 448:
Related Documentation 8. (Optional)
Page 449 and 450:
Configuring the Action Taken for th
Page 451 and 452:
• Limiting the Number of Active P
Page 453 and 454:
Reserving a Static PPPoE Interface
Page 455 and 456:
Disabling the Sending of PPPoE Acce
Page 457 and 458:
Page 459 and 460:
By default, nothing is traced. When
Page 461 and 462:
Page 463 and 464:
CHAPTER 31 Configuring Ethernet Aut
Page 465 and 466:
CLI Configuration Statements Copyri
Page 467 and 468:
Related Documentation • Ethernet
Page 469 and 470:
Page 471 and 472:
CHAPTER 32 Configuring Ethernet Rin
Page 473 and 474:
Ring Nodes Ring Node States Failure
Page 475 and 476:
The routers use an implicit filter
Page 477 and 478:
Related Documentation control-chann
Page 479 and 480:
Page 481 and 482:
Page 483 and 484:
Normal Situation—Other Nodes Fail
Page 485 and 486:
Page 487 and 488:
CHAPTER 33 Example Ethernet Configu
Page 489 and 490:
Related Documentation • } unit 1
Page 491 and 492:
PART 3 Ethernet Interface Configura
Page 493 and 494:
CHAPTER 34 Summary of Ethernet Inte
Page 495 and 496:
agent-specifier Syntax agent-specif
Page 497 and 498:
aggregated-ether-options Syntax agg
Page 499 and 500:
auto-negotiation Syntax (auto-negot
Page 501 and 502:
urst-size-limit (Policer for Gigabi
Page 503 and 504:
disable Syntax disable; Hierarchy L
Page 505 and 506:
ethernet (Protocols OAM) Syntax eth
Page 507 and 508:
status-counter number; polling-veri
Page 509 and 510:
ethernet-ring Syntax ethernet-ring
Page 511 and 512:
Required Privilege Default If the e
Page 513 and 514:
fnp Syntax fnp { interval ;; loss-t
Page 515 and 516:
flow-control-options Syntax flow-co
Page 517 and 518:
framing (10-Gigabit Ethernet Interf
Page 519 and 520:
} Hierarchy Level [edit interfaces
Page 521 and 522:
ignore-l3-incompletes Syntax ignore
Page 523 and 524:
inner-vlan-id Syntax inner-vlan-id
Page 525 and 526:
input-vlan-map See the following se
Page 527 and 528:
interface Syntax interface (all | i
Page 529 and 530:
lacp lacp (802.3ad) See the followi
Page 531 and 532:
link-discovery Syntax link-discover
Page 533 and 534:
Page 535 and 536:
Required Privilege Level Related Do
Page 537 and 538:
link-speed (Aggregated Ethernet) Sy
Page 539 and 540:
lldp-configuration-notification-int
Page 541 and 542:
mac-learn-enable Syntax (mac-learn-
Page 543 and 544:
max-sessions-vsa-ignore (Static and
Page 545 and 546:
mep Syntax mep mep-id { auto-discov
Page 547 and 548:
mip-half-function Syntax mip-half-f
Page 549 and 550:
no-auto-mdix Syntax no-auto-mdix; H
Page 551 and 552:
oam Syntax oam { ethernet { connect
Page 553 and 554:
Description For Ethernet interfaces
Page 555 and 556:
pado-advertise Syntax pado-advertis
Page 557 and 558:
periodic Syntax periodic interval;
Page 559 and 560:
policer (CFM Global) Syntax policer
Page 561 and 562:
policer (CoS) Syntax policer cos-po
Page 563 and 564:
pop Syntax pop; Hierarchy Level [ed
Page 565 and 566:
port-id-subtype Syntax port-id-subt
Page 567 and 568:
ppp-options Syntax ppp-options { au
Page 569 and 570:
pppoe-underlying-options (Static an
Page 571 and 572:
premium (Output Priority Map) Synta
Page 573 and 574:
Hierarchy Level [edit protocols] re
Page 575 and 576:
push Syntax push; Hierarchy Level [
Page 577 and 578:
ing-protection-link-end Syntax ring
Page 579 and 580:
sa-multicast (100-Gigabit Ethernet)
Page 581 and 582:
Related Documentation service-name-
Page 583 and 584:
short-cycle-protection (Static and
Page 585 and 586:
source-address-filter Syntax source
Page 587 and 588:
speed speed (Ethernet) See the foll
Page 589 and 590:
static-interface Syntax static-inte
Page 591 and 592:
swap-swap Syntax swap-swap; Hierarc
Page 593 and 594:
system-id Syntax system-id system-i
Page 595 and 596:
tag-protocol-id (TPID to Rewrite) S
Page 597 and 598:
traceoptions Syntax traceoptions {
Page 599 and 600:
traceoptions (PPPoE) Syntax traceop
Page 601 and 602:
Page 603 and 604:
Page 605 and 606:
Page 607 and 608:
(cbr rate | rtvbr burst length peak
Page 609 and 610:
vlan-id See the following sections:
Page 611 and 612:
vlan-id (VLAN ID to Rewrite) Syntax
Page 613 and 614:
vlan-id-list (Ethernet VLAN Circuit
Page 615 and 616:
vlan-id-range Syntax vlan-id-range
Page 617 and 618:
vlan-rewrite Syntax vlan-rewrite tr
Page 619 and 620:
vlan-tagging Syntax vlan-tagging; H
Page 621 and 622:
vlan-tags (Dual-Tagged Logical Inte
Page 623 and 624:
vlan-tags (Stacked VLAN Tags) Synta
Page 625 and 626:
vlan-vci-tagging Syntax vlan-vci-ta
Page 627 and 628:
Page 629 and 630:
Page 631 and 632:
PART 4 Troubleshooting Copyright ©
Page 633 and 634:
CHAPTER 35 Investigate Fast Etherne
Page 635 and 636:
h. Ping the interface. i. Check for
Page 637 and 638:
Table 38: Checklist for Monitoring
Page 639 and 640:
Meaning This sample output lists on
Page 641 and 642:
Output packets: 1642918 3 pps Input
Page 643 and 644:
autonegotiation information of the
Page 645 and 646:
Table 44: Fiber-Optic Ethernet Inte
Page 647 and 648:
Create a Loopback • Configure a S
Page 649 and 650:
use a local or remote statement. Si
Page 651 and 652:
1. Find the Media Access Control (M
Page 653 and 654:
Vr HL TOS Len ID Flg off TTL Pro ck
Page 655 and 656:
Diagnose a Suspected Circuit Proble
Page 657 and 658:
Description: Test Flags: SNMP-Traps
Page 659 and 660:
Table 48: Major Fast Ethernet and G
Page 661 and 662:
PART 5 Index Copyright © 2012, Jun
Page 663 and 664:
Index Symbols #, comments in config
Page 665 and 666:
checklist for monitoring Fast Ether
Page 667 and 668:
family bridge VLAN ID list.........
Page 669 and 670:
Gigabit Ethernet configuring.......
Page 671 and 672:
multimode fiber cable..............
Page 673 and 674:
ewrite VLAN tag on untagged frame u
Page 675 and 676:
trunk interface interface-mode stat
Page 677 and 678:
Index of Statements and Commands Sy
Page 679 and 680:
static PPPoE statements max-session
show all

Junos® OS Ethernet Interfaces Configuration ... - Juniper Networks

Create successful ePaper yourself

Delete template?

Save as template?