EQ7 Series Instruction Manual - TECO-Westinghouse Motor Company

More documents

Recommendations

Info

• When the motor speed decreases significantly during coast-to-stop (with the current limiter activated): • Secure more than 0.1 second after turning ON the "Switch to commercial power" signal before turning ON a run command. • Secure more than 0.2 second of an overlapping period with both the "Switch to commercial power" signal and run command being ON. • If an alarm has been issued or BX has been ON when the motor drive source is switched from the commercial power to the inverter, the inverter will not be started at the commercial power frequency and will remain OFF. After the alarm has been reset or BX turned OFF, operation at the frequency of the commercial power will not be continued, and the inverter will be started at the ordinary starting frequency. To switch the motor drive source from the commercial line to the inverter, be sure to turn BX OFF before the "Switch to commercial power" signal is turned OFF. • When switching the motor drive source from the inverter to commercial power, adjust the inverter's reference frequency at or slightly higher than that of the commercial power frequency beforehand, taking into consideration the motor speed down during the coast-to-stop period produced by switching. • Note that when the motor drive source is switched from the inverter to the commercial power, a high inrush current will be generated, because the phases of the commercial power usually do not match the motor speed at the switching. Make sure that the power supply and all the peripheral equipment are capable of withstanding this inrush current. • If "Restart after momentary power failure" (F14 = 3, 4, or 5), is activated keep BX ON during commercial power driven operation to prevent the inverter from restarting after a momentary power failure. 4-75
Example of Sequence Circuit Note 1) Emergency switch <strong>Manual</strong> switch provided for the event that the motor drive source cannot be switched normally to the commercial power due to a serious problem of the inverter Note 2) When any alarm has occurred inside the inverter, the motor drive source will automatically be switched to the commercial power. 4-76
Page 2 and 3:
Preface The EQ7 product is designed
Page 4 and 5:
7. Operation Method Configuration (
Page 6 and 7:
Wiring • If no zero-phase current
Page 8 and 9:
• Do not touch the heat sink and
Page 10 and 11:
Conformity with UL standards and CS
Page 12 and 13:
Conformity with UL standards and CS
Page 14 and 15:
1.1 Drive Models Constant Torque (C
Page 16 and 17:
• Storage environment The storage
Page 18 and 19:
(5) Molded case circuit breaker (MC
Page 20 and 21:
• From the system's safety point
Page 22 and 23:
1.3 Precautions in running inverter
Page 24 and 25:
Chapter 2 Mounting and Wiring the I
Page 26 and 27:
Figure 2.3 Changing the Positions o
Page 28 and 29:
2.3.2 Screw specifications and reco
Page 30 and 31:
Power supply voltage Single-phase/
Page 32 and 33:
Before removal of clip-off sections
Page 34 and 35:
2.3.4 Wiring of main circuit termin
Page 36 and 37:
DC reactor terminals P1 and P (+) C
Page 38 and 39:
• Fan power supply switching conn
Page 40 and 41:
When connecting a PWM converter wit
Page 42 and 43:
Table 2.7 lists the symbols, names
Page 44 and 45:
Table 2.7 Symbols, Names and Functi
Page 46 and 47:
Table 2.7 Symbols, Names and Functi
Page 48 and 49:
Wiring for control circuit terminal
Page 50 and 51:
2.4 Mounting and Connecting the Key
Page 52 and 53:
Never connect power supply wires to
Page 54 and 55:
Table 3.1 Overview of Keypad Functi
Page 56 and 57:
3.3 Running Mode 3.3.1 Running or s
Page 58 and 59:
Table 3.4 Items Monitored (Continue
Page 60 and 61:
3.4 Programming Mode Programming mo
Page 62 and 63:
Basic configuration of screens Figu
Page 64 and 65:
3.4.3 Checking changed function cod
Page 66 and 67:
(3) Press key to establish the desi
Page 68 and 69:
Basic key operation (1) Turn the in
Page 70 and 71:
Chapter 4 Function Codes / Paramete
Page 72 and 73:
F codes: Fundamental Functions Code
Page 74 and 75:
Code Name Data setting range F37 Lo
Page 76 and 77:
Change when running Data copying De
Page 78 and 79:
Page 80 and 81:
C codes: Control Functions of Frequ
Page 82 and 83:
H codes: High Performance Functions
Page 84 and 85:
Code Name Data setting range H73 To
Page 86 and 87:
Code Name Data setting range A18 Mo
Page 88 and 89:
J codes: Application Functions 1 Co
Page 90 and 91:
Page 92 and 93:
Inverter capacity HP 0.5 Auto-resta
Page 94 and 95: Table B Motor Parameters (Continued
Page 96 and 97: Configuring a reference frequency [
Page 98 and 99: • Gain and bias If F01 = 3 (the s
Page 100 and 101: • Specifying the initial value fo
Page 102 and 103: • Pulse count factor 1 (d62), Pul
Page 104 and 105: F03 Maximum Frequency 1 F03 specifi
Page 106 and 107: In vector control, current feedback
Page 108 and 109: • Acceleration/Deceleration patte
Page 110 and 111: F10 to F12 Electronic Thermal Overl
Page 112 and 113: F14 Restart Mode after Momentary Po
Page 114 and 115: If you enable the "Restart mode aft
Page 116 and 117: • Restart mode after momentary po
Page 118 and 119: Even if selecting "Trip after decel
Page 120 and 121: It is also possible to use an exter
Page 122 and 123: The table below shows the condition
Page 124 and 125: F29 to F31 F32, F34, F35 Analog Out
Page 126 and 127: • V/f characteristics The EQ7 ser
Page 128 and 129: Related function codes Function cod
Page 130 and 131: Under vector control without/with s
Page 132 and 133: Data for H75 Target quadrants Patte
Page 134 and 135: F42 Drive Control Selection 1 H68 (
Page 136 and 137: F43, F44 Current Limiter (Mode sele
Page 138 and 139: • Allowable average loss (F51) Th
Page 140 and 141: 4.2.2 E codes (Extension Terminal F
Page 142 and 143: Terminal function assignment and da
Page 146 and 147: Example of Operation Time Scheme Al
Page 148 and 149: When the PID control is disabled: T
Page 150 and 151: Circuit Diagram and Configuration M
Page 152 and 153: Examples of Sequence Circuits 1) St
Page 154 and 155: • Enable battery operation -- BAT
Page 156 and 157: Precautions (1) The battery power s
Page 158 and 159: Function code data Active ON Active
Page 160 and 161: • Universal DO -- U-DO (Function
Page 162 and 163: • Enable input OFF -- EN OFF (Fun
Page 164 and 165: E34, E35 Overload Early Warning/Cur
Page 166 and 167: • Display coefficients for PID da
Page 168 and 169: E44 LED Monitor (Display when stopp
Page 170 and 171: E54 Frequency Detection 3 (Level) (
Page 172 and 173: E64 Saving of Digital Reference Fre
Page 174 and 175: 4.2.3 C codes (Control functions) C
Page 176 and 177: C20 Jogging Frequency H54, H55 (Acc
Page 178 and 179: 4.2.4 P codes (Motor 1 Parameters)
Page 180 and 181: P05, A19 Motor 1 / 2 (Online tuning
Page 182 and 183: P53, P54 Motor 1 (%X correction fac
Page 184 and 185: Chapter 6 Speed Reference Command C
Page 186 and 187: Analog Reference: 0 - 20mA / 4 - 20
Page 188 and 189: H30 Communications Link Function Se
Page 190 and 191: 7.2 Run/Stop from External Switch /
Page 192 and 193: 7.3 Run/Stop from Serial Communicat
Page 194 and 195:
Chapter 8 Motor and Application Spe
Page 196 and 197:
8.3 Torque Boost (F09, Default 0.1)
Page 198 and 199:
When the variable torque V/f patter
Page 200 and 201:
Chapter 9 Using PID Control for Con
Page 202 and 203:
Feedback Signal 0 - 10V (E61 = 5) G
Page 204 and 205:
Chapter 10 Troubleshooting 10.1 Pro
Page 206 and 207:
Table 10.1 Abnormal States Detectab
Page 208 and 209:
10.3 If Neither an Alarm Code Nor "
Page 210 and 211:
Possible Causes (5) The acceleratio
Page 212 and 213:
[ 6 ] The motor does not accelerate
Page 214 and 215:
10.3.2 Problems with inverter setti
Page 216 and 217:
[ 3 ] Overvoltage Problem The DC li
Page 218 and 219:
[ 7 ] Heat sink overheat Problem Te
Page 220 and 221:
[ 12 ] Fuse blown Problem The fuse
Page 222 and 223:
[ 17 ] PG wire break Problem The pu
Page 224 and 225:
[ 24 ] Tuning error Problem Auto-tu
Page 226 and 227:
[ 28 ] Speed mismatch or excessive
Page 228 and 229:
[ 36 ] Enable circuit failure Probl
Page 230 and 231:
10.7 If the Inverter is Running on
Page 232 and 233:
VT mode designed for variable torqu
Page 234 and 235:
CT mode designed for constant torqu
Page 236 and 237:
VT mode designed for variable torqu
Page 238 and 239:
l Item Specifications Remarks Enabl
Page 240 and 241:
Item Specifications Remarks Overcur
Page 242 and 243:
11.3 External Dimensions 11.3.1 Sta
Page 244 and 245:
11.3.3 DC reactor (DCR) Power suppl
Page 246 and 247:
Figure A Figure B Figure C Figure D
Page 248:
11.3.5 Keypad (TP-G1W-J1) Drill fou
show all

EQ7 Series Instruction Manual - TECO-Westinghouse Motor Company

Create successful ePaper yourself

Delete template?

Save as template?