EQ7 Series Instruction Manual - TECO-Westinghouse Motor Company
EQ7 Series Instruction Manual - TECO-Westinghouse Motor Company
EQ7 Series Instruction Manual - TECO-Westinghouse Motor Company
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
8.5 Reset <strong>EQ7</strong> back to Factory Default<br />
Parameter H03<br />
Data Initialization<br />
H03 initializes the current function code data to the factory defaults or initializes the motor parameters.<br />
To change the H03 data, it is necessary to press the + keys or + keys (simultaneous keying).<br />
Data for H03<br />
Function<br />
0 Disable initialization (Settings manually made by the user will be retained.)<br />
1 Initialize all function code data to the factory defaults<br />
Initialize motor 1 parameters in accordance with P02 (Rated capacity) and P99 (<strong>Motor</strong> 1<br />
2<br />
selection)<br />
Initialize motor 2 parameters in accordance with A16 (Rated capacity) and A39 (<strong>Motor</strong> 2<br />
3<br />
selection)<br />
• To initialize the motor parameters, set the related function codes as follows.<br />
Function code<br />
Step Item Action<br />
1st motor<br />
2nd motor<br />
<strong>Motor</strong> Selects the motor<br />
(1)<br />
selection type<br />
P99<br />
A39<br />
<strong>Motor</strong> Sets the motor<br />
(2) (rated capacity (HP) P02 A16<br />
capacity)<br />
Data Initialize motor<br />
(3)<br />
initialization parameters H03 = 2 H03 = 3<br />
Function code data<br />
to be initialized<br />
If "Data = 0, 1, 3, or<br />
4" in Step (1)<br />
If "Data = 2" in Step<br />
(1), function codes<br />
listed at the right are<br />
also initialized<br />
P01, P03, P06 to P23,<br />
P53 to P56,H46<br />
A15, A17, A20 to A37,<br />
A53 to A56<br />
F04, F05 A02, A03<br />
• Upon completion of the initialization, the H03 data reverts to "0" (factory default).<br />
• If P02 or A16 data is set to a value other than the nominal applied motor rating, data initialization with H03<br />
internally converts the specified value forcibly to the standard nominal applied motor rating. (Refer to Table B in<br />
Section 4.1 "Function Code Tables.")<br />
• <strong>Motor</strong> parameters to be initialized are for motors listed below under V/f control. When the base frequency,<br />
rated voltage, and the number of poles are different from those of the listed motors, or when non-standard<br />
motors are used, change the rated current data to that printed on the motor nameplate.<br />
<strong>Motor</strong> selection<br />
V/f control data<br />
Data = 1 TWMC HP rating motors 4 poles 230 V/60 Hz, 460 V/60 Hz<br />
Data = 2 Consult Factory 4 poles ―/50 Hz, ―/50 Hz<br />
Data = 0 or 4 Consult Factory 4 poles 200 V/50 Hz, 400 V/50 Hz<br />
Data = 3 Consult Factory 4 poles 200 V/50 Hz, 400 V/50 Hz<br />
When accessing function code P02 with the keypad, take into account that P02 data automatically<br />
updates data of function codes P03, P06 through P23, P53 through P56, and H46. Also, when accessing<br />
function code A16, data of related function codes for each are automatically updated.<br />
8-6