EQ7 Series Instruction Manual - TECO-Westinghouse Motor Company

More documents

Recommendations

Info

H30 Communications Link Function Set value Frequency command Run command (Run/Stop) 0 F01 / C30 F02 1 Enabled / RS485 (Port 1) F02 2 F01 / C30 Enabled / RS485 (Port 1) 3 Enabled / RS485 (Port 1) Enabled / RS485 (Port 1) 4 Enabled / RS485 (Port 2) F02 5 Enabled / RS485 (Port 2) Enabled / RS485 (Port 1) 6 F01 / C30 Enabled / RS485 (Port 2) 7 Enabled / RS485 (Port 1) Enabled / RS485 (Port 2) 8 Enabled / RS485 (Port 2) Enabled / RS485 (Port 2) Frequency Reference Command Register EQ7 Drive Frequency Reference Register: 1797 (Decimal) - Bit 0 – Bit 15: 0.00 ~ 120.00 Hz Examples: Frequency Reference Command: 10.00 Hz (EQ7 Drive Address: 01) Command String (hexadecimal): 01 06 07 05 03 E8 98 01 To set the frequency reference to 10.00, a value of ‘1000’ (03E8h) has to be send to the EQ7 Drive Frequency Reference Command: 30.00 Hz (EQ7 Drive Address: 01) Command String (hexadecimal): 01 06 07 05 0B B8 9F FD To set the frequency reference to 30.00, a value of ‘3000’ (0BB8h) has to be send to the EQ7 Drive Frequency Reference Command: 60.00 Hz (EQ7 Drive Address: 01) Command String (hexadecimal): 01 06 07 05 17 70 96 AB To set the frequency reference to 60.00, a value of ‘6000’ (1770h) has to be send to the EQ7 Drive Note: The last 2 bytes of the command strings consist of a CRC16 checksum, please refer to the Refer to the EQ7 Communications Manual for additional information. 6-5
Chapter 7 Operation Method Configuration (Run / Stop) The EQ7 Drive offers users several choices to run and stop the drive from different sources. The most commonly used methods are described in the next sections. F02 Operation Method This function sets the operation method (Run/Stop) source. Setting Range: 0 – 3 To set parameter F02: - Press PRG key, next select QUICK SET or DATA SET with UP/DOWN and keys and press the FUNC/DATA key. - In the parameter list move cursor to F02 with UP/DOWN keys and press FUNC/DATA key to select. Data for F02 0 Keypad 1 2 3 Run Command Terminal command FWD or REV Keypad (Forward rotation) Keypad (Reverse rotation) Description Enables the , , and keys to run the motor in the forward and reverse directions, and stop the motor. Enables input terminal commands FWD and REV to run the motor in the forward and reverse directions, and stop the motor. Enables the and keys to run the motor in the forward direction and stop it. Running the motor in the reverse direction is not possible. Enables the and keys to run the motor in the reverse direction and stop it. Running the motor in the forward direction is not possible. 7.1 Run/Stop from Keypad (Default Setting, F02 = 0) Run from digital operator (Keypad) is the default setting. Use the key to run the drive in forward direction and the key to run the EQ7 drive in reverse direction. (Note: to disable reverse direction set parameter H08 to 1) Press key to stop the EQ7 drive. (Note: Stop method can be set with parameter H07, default is ramp to stop). 7-1
Page 2 and 3:
Preface The EQ7 product is designed
Page 4 and 5:
7. Operation Method Configuration (
Page 6 and 7:
Wiring • If no zero-phase current
Page 8 and 9:
• Do not touch the heat sink and
Page 10 and 11:
Conformity with UL standards and CS
Page 12 and 13:
Conformity with UL standards and CS
Page 14 and 15:
1.1 Drive Models Constant Torque (C
Page 16 and 17:
• Storage environment The storage
Page 18 and 19:
(5) Molded case circuit breaker (MC
Page 20 and 21:
• From the system's safety point
Page 22 and 23:
1.3 Precautions in running inverter
Page 24 and 25:
Chapter 2 Mounting and Wiring the I
Page 26 and 27:
Figure 2.3 Changing the Positions o
Page 28 and 29:
2.3.2 Screw specifications and reco
Page 30 and 31:
Power supply voltage Single-phase/
Page 32 and 33:
Before removal of clip-off sections
Page 34 and 35:
2.3.4 Wiring of main circuit termin
Page 36 and 37:
DC reactor terminals P1 and P (+) C
Page 38 and 39:
• Fan power supply switching conn
Page 40 and 41:
When connecting a PWM converter wit
Page 42 and 43:
Table 2.7 lists the symbols, names
Page 44 and 45:
Table 2.7 Symbols, Names and Functi
Page 46 and 47:
Table 2.7 Symbols, Names and Functi
Page 48 and 49:
Wiring for control circuit terminal
Page 50 and 51:
2.4 Mounting and Connecting the Key
Page 52 and 53:
Never connect power supply wires to
Page 54 and 55:
Table 3.1 Overview of Keypad Functi
Page 56 and 57:
3.3 Running Mode 3.3.1 Running or s
Page 58 and 59:
Table 3.4 Items Monitored (Continue
Page 60 and 61:
3.4 Programming Mode Programming mo
Page 62 and 63:
Basic configuration of screens Figu
Page 64 and 65:
3.4.3 Checking changed function cod
Page 66 and 67:
(3) Press key to establish the desi
Page 68 and 69:
Basic key operation (1) Turn the in
Page 70 and 71:
Chapter 4 Function Codes / Paramete
Page 72 and 73:
F codes: Fundamental Functions Code
Page 74 and 75:
Code Name Data setting range F37 Lo
Page 76 and 77:
Change when running Data copying De
Page 78 and 79:
Page 80 and 81:
C codes: Control Functions of Frequ
Page 82 and 83:
H codes: High Performance Functions
Page 84 and 85:
Code Name Data setting range H73 To
Page 86 and 87:
Code Name Data setting range A18 Mo
Page 88 and 89:
J codes: Application Functions 1 Co
Page 90 and 91:
Page 92 and 93:
Inverter capacity HP 0.5 Auto-resta
Page 94 and 95:
Table B Motor Parameters (Continued
Page 96 and 97:
Configuring a reference frequency [
Page 98 and 99:
• Gain and bias If F01 = 3 (the s
Page 100 and 101:
• Specifying the initial value fo
Page 102 and 103:
• Pulse count factor 1 (d62), Pul
Page 104 and 105:
F03 Maximum Frequency 1 F03 specifi
Page 106 and 107:
In vector control, current feedback
Page 108 and 109:
• Acceleration/Deceleration patte
Page 110 and 111:
F10 to F12 Electronic Thermal Overl
Page 112 and 113:
F14 Restart Mode after Momentary Po
Page 114 and 115:
If you enable the "Restart mode aft
Page 116 and 117:
• Restart mode after momentary po
Page 118 and 119:
Even if selecting "Trip after decel
Page 120 and 121:
It is also possible to use an exter
Page 122 and 123:
The table below shows the condition
Page 124 and 125:
F29 to F31 F32, F34, F35 Analog Out
Page 126 and 127:
• V/f characteristics The EQ7 ser
Page 128 and 129:
Related function codes Function cod
Page 130 and 131:
Under vector control without/with s
Page 132 and 133:
Data for H75 Target quadrants Patte
Page 134 and 135:
F42 Drive Control Selection 1 H68 (
Page 136 and 137:
F43, F44 Current Limiter (Mode sele
Page 138 and 139: • Allowable average loss (F51) Th
Page 140 and 141: 4.2.2 E codes (Extension Terminal F
Page 142 and 143: Terminal function assignment and da
Page 144 and 145: • When the motor speed decreases
Page 146 and 147: Example of Operation Time Scheme Al
Page 148 and 149: When the PID control is disabled: T
Page 150 and 151: Circuit Diagram and Configuration M
Page 152 and 153: Examples of Sequence Circuits 1) St
Page 154 and 155: • Enable battery operation -- BAT
Page 156 and 157: Precautions (1) The battery power s
Page 158 and 159: Function code data Active ON Active
Page 160 and 161: • Universal DO -- U-DO (Function
Page 162 and 163: • Enable input OFF -- EN OFF (Fun
Page 164 and 165: E34, E35 Overload Early Warning/Cur
Page 166 and 167: • Display coefficients for PID da
Page 168 and 169: E44 LED Monitor (Display when stopp
Page 170 and 171: E54 Frequency Detection 3 (Level) (
Page 172 and 173: E64 Saving of Digital Reference Fre
Page 174 and 175: 4.2.3 C codes (Control functions) C
Page 176 and 177: C20 Jogging Frequency H54, H55 (Acc
Page 178 and 179: 4.2.4 P codes (Motor 1 Parameters)
Page 180 and 181: P05, A19 Motor 1 / 2 (Online tuning
Page 182 and 183: P53, P54 Motor 1 (%X correction fac
Page 184 and 185: Chapter 6 Speed Reference Command C
Page 186 and 187: Analog Reference: 0 - 20mA / 4 - 20
Page 190 and 191: 7.2 Run/Stop from External Switch /
Page 192 and 193: 7.3 Run/Stop from Serial Communicat
Page 194 and 195: Chapter 8 Motor and Application Spe
Page 196 and 197: 8.3 Torque Boost (F09, Default 0.1)
Page 198 and 199: When the variable torque V/f patter
Page 200 and 201: Chapter 9 Using PID Control for Con
Page 202 and 203: Feedback Signal 0 - 10V (E61 = 5) G
Page 204 and 205: Chapter 10 Troubleshooting 10.1 Pro
Page 206 and 207: Table 10.1 Abnormal States Detectab
Page 208 and 209: 10.3 If Neither an Alarm Code Nor "
Page 210 and 211: Possible Causes (5) The acceleratio
Page 212 and 213: [ 6 ] The motor does not accelerate
Page 214 and 215: 10.3.2 Problems with inverter setti
Page 216 and 217: [ 3 ] Overvoltage Problem The DC li
Page 218 and 219: [ 7 ] Heat sink overheat Problem Te
Page 220 and 221: [ 12 ] Fuse blown Problem The fuse
Page 222 and 223: [ 17 ] PG wire break Problem The pu
Page 224 and 225: [ 24 ] Tuning error Problem Auto-tu
Page 226 and 227: [ 28 ] Speed mismatch or excessive
Page 228 and 229: [ 36 ] Enable circuit failure Probl
Page 230 and 231: 10.7 If the Inverter is Running on
Page 232 and 233: VT mode designed for variable torqu
Page 234 and 235: CT mode designed for constant torqu
Page 236 and 237: VT mode designed for variable torqu
Page 238 and 239:
l Item Specifications Remarks Enabl
Page 240 and 241:
Item Specifications Remarks Overcur
Page 242 and 243:
11.3 External Dimensions 11.3.1 Sta
Page 244 and 245:
11.3.3 DC reactor (DCR) Power suppl
Page 246 and 247:
Figure A Figure B Figure C Figure D
Page 248:
11.3.5 Keypad (TP-G1W-J1) Drill fou
show all

EQ7 Series Instruction Manual - TECO-Westinghouse Motor Company

Create successful ePaper yourself

Delete template?

Save as template?