EQ7 Series Instruction Manual - TECO-Westinghouse Motor Company

More documents

Recommendations

Info

7.2 Run/Stop from External Switch / Contact or Pushbutton (F02 = 1) Use an external contact or switch to Run and Stop the <strong>EQ7</strong> drive. Permanent Switch / Contact Control Terminals / User Terminals Common/CM Forward Command/FWD START / STOP SWITCH (Maintained) G Connect shield to ground terminal 7-2
Momentary Contacts (Push Buttons) Use push button / momentary switch to Run and Stop the <strong>EQ7</strong> drive. F02 Operation Method = 1 E07 Terminal [X7] Function = 6 Control Terminals / User Terminals G Connect shield to ground terminal Common/CM START PUSH BUTTON (Momentary) Forward Command/FWD STOP PUSH BUTTON (Momentary) X7 Programmed to Hold Function Note: Stop method can be set with parameter H07, default is ramp to stop. 7-3
Page 2 and 3:
Preface The EQ7 product is designed
Page 4 and 5:
7. Operation Method Configuration (
Page 6 and 7:
Wiring • If no zero-phase current
Page 8 and 9:
• Do not touch the heat sink and
Page 10 and 11:
Conformity with UL standards and CS
Page 12 and 13:
Conformity with UL standards and CS
Page 14 and 15:
1.1 Drive Models Constant Torque (C
Page 16 and 17:
• Storage environment The storage
Page 18 and 19:
(5) Molded case circuit breaker (MC
Page 20 and 21:
• From the system's safety point
Page 22 and 23:
1.3 Precautions in running inverter
Page 24 and 25:
Chapter 2 Mounting and Wiring the I
Page 26 and 27:
Figure 2.3 Changing the Positions o
Page 28 and 29:
2.3.2 Screw specifications and reco
Page 30 and 31:
Power supply voltage Single-phase/
Page 32 and 33:
Before removal of clip-off sections
Page 34 and 35:
2.3.4 Wiring of main circuit termin
Page 36 and 37:
DC reactor terminals P1 and P (+) C
Page 38 and 39:
• Fan power supply switching conn
Page 40 and 41:
When connecting a PWM converter wit
Page 42 and 43:
Table 2.7 lists the symbols, names
Page 44 and 45:
Table 2.7 Symbols, Names and Functi
Page 46 and 47:
Table 2.7 Symbols, Names and Functi
Page 48 and 49:
Wiring for control circuit terminal
Page 50 and 51:
2.4 Mounting and Connecting the Key
Page 52 and 53:
Never connect power supply wires to
Page 54 and 55:
Table 3.1 Overview of Keypad Functi
Page 56 and 57:
3.3 Running Mode 3.3.1 Running or s
Page 58 and 59:
Table 3.4 Items Monitored (Continue
Page 60 and 61:
3.4 Programming Mode Programming mo
Page 62 and 63:
Basic configuration of screens Figu
Page 64 and 65:
3.4.3 Checking changed function cod
Page 66 and 67:
(3) Press key to establish the desi
Page 68 and 69:
Basic key operation (1) Turn the in
Page 70 and 71:
Chapter 4 Function Codes / Paramete
Page 72 and 73:
F codes: Fundamental Functions Code
Page 74 and 75:
Code Name Data setting range F37 Lo
Page 76 and 77:
Change when running Data copying De
Page 78 and 79:
Page 80 and 81:
C codes: Control Functions of Frequ
Page 82 and 83:
H codes: High Performance Functions
Page 84 and 85:
Code Name Data setting range H73 To
Page 86 and 87:
Code Name Data setting range A18 Mo
Page 88 and 89:
J codes: Application Functions 1 Co
Page 90 and 91:
Page 92 and 93:
Inverter capacity HP 0.5 Auto-resta
Page 94 and 95:
Table B Motor Parameters (Continued
Page 96 and 97:
Configuring a reference frequency [
Page 98 and 99:
• Gain and bias If F01 = 3 (the s
Page 100 and 101:
• Specifying the initial value fo
Page 102 and 103:
• Pulse count factor 1 (d62), Pul
Page 104 and 105:
F03 Maximum Frequency 1 F03 specifi
Page 106 and 107:
In vector control, current feedback
Page 108 and 109:
• Acceleration/Deceleration patte
Page 110 and 111:
F10 to F12 Electronic Thermal Overl
Page 112 and 113:
F14 Restart Mode after Momentary Po
Page 114 and 115:
If you enable the "Restart mode aft
Page 116 and 117:
• Restart mode after momentary po
Page 118 and 119:
Even if selecting "Trip after decel
Page 120 and 121:
It is also possible to use an exter
Page 122 and 123:
The table below shows the condition
Page 124 and 125:
F29 to F31 F32, F34, F35 Analog Out
Page 126 and 127:
• V/f characteristics The EQ7 ser
Page 128 and 129:
Related function codes Function cod
Page 130 and 131:
Under vector control without/with s
Page 132 and 133:
Data for H75 Target quadrants Patte
Page 134 and 135:
F42 Drive Control Selection 1 H68 (
Page 136 and 137:
F43, F44 Current Limiter (Mode sele
Page 138 and 139:
• Allowable average loss (F51) Th
Page 140 and 141: 4.2.2 E codes (Extension Terminal F
Page 142 and 143: Terminal function assignment and da
Page 144 and 145: • When the motor speed decreases
Page 146 and 147: Example of Operation Time Scheme Al
Page 148 and 149: When the PID control is disabled: T
Page 150 and 151: Circuit Diagram and Configuration M
Page 152 and 153: Examples of Sequence Circuits 1) St
Page 154 and 155: • Enable battery operation -- BAT
Page 156 and 157: Precautions (1) The battery power s
Page 158 and 159: Function code data Active ON Active
Page 160 and 161: • Universal DO -- U-DO (Function
Page 162 and 163: • Enable input OFF -- EN OFF (Fun
Page 164 and 165: E34, E35 Overload Early Warning/Cur
Page 166 and 167: • Display coefficients for PID da
Page 168 and 169: E44 LED Monitor (Display when stopp
Page 170 and 171: E54 Frequency Detection 3 (Level) (
Page 172 and 173: E64 Saving of Digital Reference Fre
Page 174 and 175: 4.2.3 C codes (Control functions) C
Page 176 and 177: C20 Jogging Frequency H54, H55 (Acc
Page 178 and 179: 4.2.4 P codes (Motor 1 Parameters)
Page 180 and 181: P05, A19 Motor 1 / 2 (Online tuning
Page 182 and 183: P53, P54 Motor 1 (%X correction fac
Page 184 and 185: Chapter 6 Speed Reference Command C
Page 186 and 187: Analog Reference: 0 - 20mA / 4 - 20
Page 188 and 189: H30 Communications Link Function Se
Page 192 and 193: 7.3 Run/Stop from Serial Communicat
Page 194 and 195: Chapter 8 Motor and Application Spe
Page 196 and 197: 8.3 Torque Boost (F09, Default 0.1)
Page 198 and 199: When the variable torque V/f patter
Page 200 and 201: Chapter 9 Using PID Control for Con
Page 202 and 203: Feedback Signal 0 - 10V (E61 = 5) G
Page 204 and 205: Chapter 10 Troubleshooting 10.1 Pro
Page 206 and 207: Table 10.1 Abnormal States Detectab
Page 208 and 209: 10.3 If Neither an Alarm Code Nor "
Page 210 and 211: Possible Causes (5) The acceleratio
Page 212 and 213: [ 6 ] The motor does not accelerate
Page 214 and 215: 10.3.2 Problems with inverter setti
Page 216 and 217: [ 3 ] Overvoltage Problem The DC li
Page 218 and 219: [ 7 ] Heat sink overheat Problem Te
Page 220 and 221: [ 12 ] Fuse blown Problem The fuse
Page 222 and 223: [ 17 ] PG wire break Problem The pu
Page 224 and 225: [ 24 ] Tuning error Problem Auto-tu
Page 226 and 227: [ 28 ] Speed mismatch or excessive
Page 228 and 229: [ 36 ] Enable circuit failure Probl
Page 230 and 231: 10.7 If the Inverter is Running on
Page 232 and 233: VT mode designed for variable torqu
Page 234 and 235: CT mode designed for constant torqu
Page 236 and 237: VT mode designed for variable torqu
Page 238 and 239: l Item Specifications Remarks Enabl
Page 240 and 241:
Item Specifications Remarks Overcur
Page 242 and 243:
11.3 External Dimensions 11.3.1 Sta
Page 244 and 245:
11.3.3 DC reactor (DCR) Power suppl
Page 246 and 247:
Figure A Figure B Figure C Figure D
Page 248:
11.3.5 Keypad (TP-G1W-J1) Drill fou
show all

EQ7 Series Instruction Manual - TECO-Westinghouse Motor Company

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?