Tsunami MP.11 Installation and Management Model 5012-SUR ...

More documents

Recommendations

Info

System Overview Tsunami MP.11 5012-SUR Installation and Management Virtual Local Area Networks (VLANs) • SU VLAN Mode: The SU VLAN mode can be either Transparent, Trunk, Access, or Mixed (by default, the SU is in Transparent mode). • Access VLAN ID: The Access VLAN ID is configurable in any mode, but applies only when the SU is in Access mode. The Access VLAN ID values range from 1 to 4094; the default value is 1. • Access VLAN Priority: The Access VLAN Priority is configurable in any mode, but applies only when the SU is in Access mode. The Access VLAN priority values range from 0 to 7; the default priority is 0. For voice frames, the priority field is set to the VoIP configured value (5 according to latest IETF draft, or 6 according to IEEE 802.1D) regardless of the priority value configured. • Management VLAN ID: The management VLAN ID is configurable in any mode. The management VLAN ID has a default value of untagged (-1) and may be configured with a value in the range of 1 to 4094. • Management Priority: The Management VLAN priority values range from 0 to 7 and the default priority is 0 (zero). • Outer VLAN ID: The Outer VLAN ID is configurable only in Trunk mode. If this parameter is set to -1, the QinQ mechanism is disabled by default. If this parameter is set to any number between 1 and 4094, all tagged data is appended with an additional VLAN ID as the outer VLAN ID. • Outer Priority: The Outer VLAN Priority is configurable only in Trunk mode, and applies only when the SU is in Trunk mode and the Outer VLAN ID is configured to a value between 1 and 4094. The Outer VLAN Priority values range from 0 to 7; the default priority is 0. For voice frames, the priority field is set to the VoIP configured value, regardless of the priority value configured. • VLAN 1-16: The VLAN IDs are configurable in any mode, but apply only when the SU is in Trunk mode and Mixed mode. The VLAN ID values range from 1 to 4094; the default value is untagged (-1). The maximum number of VLAN IDs that can be configured in the SU VLAN Table is 16 for each SU. The SU VLAN IDs must be in the BSU VLAN Table that corresponds to the BSU. Edit SU Table Entries To edit SU table entries, click Edit/Delete Table Entries; make your changes on the window displayed, then click OK to save your changes. NOTE: If an SU is associated to a BSU, it cannot be deleted from the VLAN table. Typical User VLAN Configurations VLANs segment network traffic into groups, which lets you limit broadcast and multicast traffic. These groups enable hosts from different VLANs to access different resources using the same network infrastructure. Hosts using the same physical network are limited to those resources available to their workgroup. The unit can segment users into a maximum of 16 different VLANs per unit, based upon a VLAN ID. The primary scenarios for using VLAN workgroups are as follows: • VLAN disabled: Your network does not use VLANs. 38
System Overview Tsunami MP.11 5012-SUR Installation and Management Virtual Local Area Networks (VLANs) • VLAN enabled: Each VLAN workgroup uses a different VLAN ID Tag. A mixture of Tagged and Untagged workgroups may be supported. SU VLAN Functionality To change SU VLAN Status, select Enable/Disable from the drop-down menu. Make your changes on the window displayed, then click OK to save your changes. SU VLAN status is a user-defined parameter. When SU VLAN status is enabled, SU operates with the VLAN parameters configured on SU. During SU registration with BSU, if BSU offers a VLAN configuration to SU, SU ignores the VLAN configuration received from BSU and sends its own configuration to BSU. Also SU sends its new VLAN configuration to BSU whenever VLAN parameters are modified. 39
Page 1 and 2: Tsunami MP.11 Installation and Mana
Page 3 and 4: Tsunami MP.11 5012-SUR Installation
Page 9 and 10: Introduction Tsunami MP.11 5012-SUR
Page 15 and 16: Installation and Initialization Tsu
Page 29 and 30: System Overview Tsunami MP.11 5012-
Page 37: System Overview Tsunami MP.11 5012-
Page 49 and 50: Basic Management Tsunami MP.11 5012
Page 59 and 60: Configuration Tsunami MP.11 5012-SU
Page 89 and 90:
Configuration Tsunami MP.11 5012-SU
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Monitoring Tsunami MP.11 5012-SUR I
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Tsunami MP.11 5012-SUR Installation
Page 117 and 118:
Commands Tsunami MP.11 5012-SUR Ins
Page 119 and 120:
Commands Tsunami MP.11 5012-SUR Ins
Page 121 and 122:
Page 123 and 124:
Procedures Tsunami MP.11 5012-SUR I
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Troubleshooting Tsunami MP.11 5012-
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Country Codes and Channels Tsunami
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Technical Specifications Tsunami MP
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Technical Services and Support Tsun
Page 161 and 162:
show all

Tsunami MP.11 Installation and Management Model 5012-SUR ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?