Tsunami MP.11 Installation and Management Model 5012-SUR ...
Tsunami MP.11 Installation and Management Model 5012-SUR ...
Tsunami MP.11 Installation and Management Model 5012-SUR ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Configuration <strong>Tsunami</strong> <strong>MP.11</strong> <strong>5012</strong>-<strong>SUR</strong> <strong>Installation</strong> <strong>and</strong> <strong>Management</strong><br />
Interface Parameters<br />
Take care when configuring a remote interface; check the available signal level first, using Remote Link Test.<br />
WARNING: When the remote interface accidentally is set at too small a value <strong>and</strong> communication is lost, it<br />
cannot be reconfigured remotely <strong>and</strong> a local action is required to bring the communication back.<br />
Therefore, the best place to experiment with the level is at the unit that can be managed without<br />
going through the link; if the link is lost, the setting can be adjusted to the correct level to bring<br />
the link back.<br />
Make your density selection from the drop-down menu. This setting requires a reboot of the unit. Sensitivity threshold<br />
settings related to the density settings for the <strong>5012</strong>-<strong>SUR</strong> are:<br />
Satellite Density Receive Sensitivity Threshold Defer Threshold<br />
Large -95 dBm -62 dBm<br />
Medium -86 dBm -62 dBm<br />
Small -78 dBm -52 dBm<br />
Mini -70 dBm -42 dBm<br />
Micro -62 dBm -36 dBm<br />
• Registration Timeout: This is the registration process time-out of an SU on a BSU. Default is 5 seconds.<br />
• Rx Activity Timeout: This is the activity time-out of an SU on a BSU. Default is 0 seconds.<br />
• WORP Error Percentage Threshold: This parameter is used to configure WORP Error Percentage Threshold for the<br />
generation of Trap. The device calculates the WORP errors percentage every second. If the error percentage is more<br />
than the configured threshold, trap is generated. This trap is not generated when the value is set to 0. Its default value<br />
is 0.<br />
• RSSI DropThreshold: This parameter is used to configure RSSI DropThreshold for generating "RSSI Drop Threshold<br />
trap". The device monitors the RSSI level <strong>and</strong> if the RSSI, over a minute drops, by more than the configured threshold<br />
a RSSI Drop Threshold Trap is generated. Its default value is 0.<br />
• SU DFS: Select Enable to enable the DFS functionality on the SU. By default, it is disabled. As the name indicates,<br />
this parameter is applicable to SUs only.<br />
• Network Secret: A network secret is a secret password given to all nodes of a network. An SU can only register to a<br />
BSU if it has the same Network Secret. The Network Secret is sent encrypted <strong>and</strong> can be used as a security option.<br />
• Input / Output B<strong>and</strong>width Limit: These parameters limit the data traffic received on the wireless interface <strong>and</strong><br />
transmitted to the wireless interface, respectively. Selections are in steps of 64 Kbps from 64 Kbps to 108,064<br />
Kbps.The default Input <strong>and</strong> Output B<strong>and</strong>width Throttling <strong>Model</strong> values are based on the device model. The default<br />
values for various models are as given below:<br />
<strong>Model</strong> Name<br />
Parameter Value<br />
Input B<strong>and</strong>width limit (Kbps) Output B<strong>and</strong>width limit (Kbps)<br />
5054-R(BSU Mode) 36032 36032<br />
5054-R(SU Mode) 108032 108032<br />
<strong>5012</strong> SU* 6016 6016<br />
<strong>5012</strong>-CPE SU* 11008 1024<br />
*For <strong>5012</strong> SU <strong>and</strong> <strong>5012</strong>-CPE SU, if an Input or Output B<strong>and</strong>width value is modified then the other value adjusts<br />
automatically to maintain an aggregate of Input <strong>and</strong> Output limit values to 11.75 Mbps only if the user configured value<br />
exceeds the aggregate of 11.75Mbps.<br />
NOTE: The aggregate maximum b<strong>and</strong>width shared between input <strong>and</strong> output is 12 Mbps. If you attempt to set the input/<br />
output b<strong>and</strong>width values so that the total exceeds 12 Mbps, the management interface will automatically adjust<br />
the values to the available aggregate b<strong>and</strong>width of 12 Mbps. For example, the system default is 6 Mbps for both<br />
input <strong>and</strong> output b<strong>and</strong>widths. If you change the input to 8 Mbps, the management interface will automatically<br />
adjust the output to 4 Mbps, for an aggregate b<strong>and</strong>width of 12 Mbps. The values will not adjust automatically if<br />
the total is less than 12 Mbps.<br />
76