Tsunami MP.11 Installation and Management Model 5012-SUR ...

More documents

Recommendations

Info

Configuration Tsunami MP.11 5012-SUR Installation and Management Network Parameters If SNTP feature is enabled, the device will attempt to retrieve the time of day from the configured time servers (primary or secondary). If successful, the TMP device will periodically poll the timeserver it has communicated with to synchronize the time of day information. If SNTP is disabled, or if it fails to communicate with the configured time servers, it will use the system uptime to update the relevant time objects. If this feature is disabled, then you can manually configure the date and time parameters. If you do not configure these objects manually, then they will be populated with the device’s system uptime. NOTES:The time servers can be configured using either the host name (Domain Name) or the IP address. If these servers are configured with the host name, then the DNS client feature must be enabled and configured properly. • If a time server is configured with a 0.0.0.0 IP address, then the SNTP client in the TMP device will not send a time request to that server. • When SNTP is enabled, it will take some time for the device to retrieve the time of day from the configured time servers and update the relevant date and time parameters. Primary and Secondary SNTP Servers The SNTP client first attempts to retrieve the time of day from the configured primary server. If the device does not receive a response from the primary server, then it tries the secondary server. If the device does not receive a response from the secondary server, then it again attempts the primary server. The device retries a total of three times the primary and secondary servers. DNS Server requirement When you configure the Domain Name of the SNTP server, the device resolves the SNTP server address with either primary or secondary DNS server. Synchronizing Time of Day If the SNTP client is successful in retrieving the time of day information, then it resends time of day requests to the server it is communicating with every ten minutes. This is a fixed value and is not configurable. This is done in order to synchronize the time. Configuring SNTP-DNS Click Configure > Network > SNTP-DNS to enable the SNTP-DNS feature. The following parameters are configurable. 1. DNS Client • DNS Client Status: Enable DNS Client by selecting Enable from the DNS Client Status drop-down menu. • DNS Primary Server IP Address: Represents the primary SNTP server IP address or host name. • DNS Secondary Server IP Address: Represents the secondary SNTP server IP address or host name. • DNS Client Default Domain Name: Represents the default domain name of the DNS Client. 2. SNTP • Enable SNTP Status: Enable SNTP Status by selecting the Enable SNTP Status checkbox. NOTE: The following fields are configurable only when SNTP Status is enabled. • Address Format: Specifies whether the host name or IP address is used in configuring the primary and secondary SNTP servers. By default, IP address is used in configuring the primary and secondary SNTP servers. • Primary Time server: Represents the primary SNTP server IP address or host name. • Secondary Time Server: Represents the secondary SNTP server IP address or host name. • Time Zone:Select the appropriate time zone for your device. 68
Configuration Tsunami MP.11 5012-SUR Installation and Management Network Parameters • Daylight Saving: Select the number of hours to adjust for Daylight Saving Time. NOTE: The following fields are configurable only when SNTP Status is disabled. • Date: You can manually configure the date in case the Date is not retrieved from a SNTP server. • Time: You can manually configure the time in case theTime is not retrieved from a SNTP server. IP Routes (Routing Mode only) NOTE: The unit must be in Routing mode to configure IP Routes. Click Configure > Network > IP Routes to configure. 69
Page 1 and 2:
Tsunami MP.11 Installation and Mana
Page 3 and 4:
Tsunami MP.11 5012-SUR Installation
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Introduction Tsunami MP.11 5012-SUR
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Installation and Initialization Tsu
Page 17 and 18: Installation and Initialization Tsu
Page 29 and 30: System Overview Tsunami MP.11 5012-
Page 47 and 48: Tsunami MP.11 5012-SUR Installation
Page 49 and 50: Basic Management Tsunami MP.11 5012
Page 59 and 60: Configuration Tsunami MP.11 5012-SU
Page 67: Configuration Tsunami MP.11 5012-SU
Page 101 and 102: Monitoring Tsunami MP.11 5012-SUR I
Page 117 and 118: Commands Tsunami MP.11 5012-SUR Ins
Page 119 and 120:
Commands Tsunami MP.11 5012-SUR Ins
Page 121 and 122:
Page 123 and 124:
Procedures Tsunami MP.11 5012-SUR I
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Troubleshooting Tsunami MP.11 5012-
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Country Codes and Channels Tsunami
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Technical Specifications Tsunami MP
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Technical Services and Support Tsun
Page 161 and 162:
show all

Tsunami MP.11 Installation and Management Model 5012-SUR ...

Create successful ePaper yourself

Delete template?

Save as template?