Tsunami MP.11 Installation and Management Model 5012-SUR ...

More documents

Recommendations

Info

Configuration Tsunami MP.11 5012-SUR Installation and Management Syslog Parameters Syslog Parameters Overview System log messages are generated by the system by sending requests at various instances to the system log server. Every message in the system carries a priority of that message. This priority indicates the importance of the message. The messages which have a priority higher than the configured syslog priority are sent to Syslog Server. The Syslog tab is used to configure hosts or servers on the network that will receive syslog messages from the device. System message logging can be disabled if needed. 1. Click Configure > Syslog to enable Syslog support for the device. The following parameters are configurable. • Enable Syslog: Select Enable Syslog checkbox to enable the Syslog functionality. To disable this functionality, clear this checkbox. • Syslog Lowest Priority Logged: The messages which have a priority lower (numerical value) than the configured Syslog priorities are sent to Syslog Server. The numerical values of the Syslog Priority messages are described below: Emergency: 0 Alert:1 Critical: 2 Error: 3 Warning: 4 Notice: 5 Info: 6 Debug: 7 Select the desired message priority from the Syslog Priority list. • Syslog Heartbeat Status: Heartbeat messages are dummy messages which are logged periodically to the syslog server. Select Enable to enable logging of Heartbeat messages by the syslog service. • Syslog HeartBeat Interval: Specifies the heartbeat message interval for which the heartbeat messages will be logged in seconds. By default, the Syslog HeartBeat Interval is 900 seconds. 2. Enter values for these parameters, and click OK. 92
Configuration Tsunami MP.11 5012-SUR Installation and Management Syslog Parameters Syslog Host Table To add entries to the Syslog Host Table, click Add Table Entries. Enter the IP Address of the syslog server in the IP Address field. Enter a Port Number (between 1 - 65535) in the Port Number field and enter an optional comment in the Comment field. Then click Add to add the entry. To modify a Syslog Host Table entry, click Edit Table Entries. 93
Page 1 and 2:
Tsunami MP.11 Installation and Mana
Page 3 and 4:
Tsunami MP.11 5012-SUR Installation
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Introduction Tsunami MP.11 5012-SUR
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Installation and Initialization Tsu
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
System Overview Tsunami MP.11 5012-
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42: System Overview Tsunami MP.11 5012-
Page 47 and 48: Tsunami MP.11 5012-SUR Installation
Page 49 and 50: Basic Management Tsunami MP.11 5012
Page 59 and 60: Configuration Tsunami MP.11 5012-SU
Page 91: Configuration Tsunami MP.11 5012-SU
Page 101 and 102: Monitoring Tsunami MP.11 5012-SUR I
Page 117 and 118: Commands Tsunami MP.11 5012-SUR Ins
Page 119 and 120: Commands Tsunami MP.11 5012-SUR Ins
Page 123 and 124: Procedures Tsunami MP.11 5012-SUR I
Page 133 and 134: Troubleshooting Tsunami MP.11 5012-
Page 139 and 140: Country Codes and Channels Tsunami
Page 141 and 142: Country Codes and Channels Tsunami
Page 143 and 144:
Country Codes and Channels Tsunami
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Technical Specifications Tsunami MP
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Technical Services and Support Tsun
Page 161 and 162:
show all

Tsunami MP.11 Installation and Management Model 5012-SUR ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?