Tsunami MP.11 Installation and Management Model 5012-SUR ...

More documents

Recommendations

Info

Configuration Tsunami MP.11 5012-SUR Installation and Management RIP Parameters (Routing Mode Only) RIP Parameters (Routing Mode Only) Routing Internet Protocol (RIP) is a dynamic routing protocol you can use to help automatically propagate routing table information between routers. The unit can be configured as RIPv1, RIPv2, RIPv1 compatible, or a combination of all three versions while operating in Routing mode. In general, the unit’s RIP module is based upon RFC 1389. NOTE: RIP is configurable only when the unit is in Routing Mode and Network Address Translation (NAT) is disabled. Note the following: • RIPv2 is enabled by default when routing mode is selected. • You may turn RIP off by clearing the Enable RIP Interface check box for the Ethernet or the wireless interface. Any RIP advertisements that are received on the designated interface are ignored. All other options on the page are dimmed. • If the Enable RIP Interface check box is selected, the unit sends RIP requests and “listens” for RIP updates coming from RIP-enabled devices advertising on the network. You may configure the Receive field for RIPv1, RIPv2, or a combination of both. Although the unit receives and processes these updates, it does not further propagate these updates unless configured to advertise RIP. Again, you may configure the Advertize field for RIPv1, RIPv2, or a combination of both. • The ability to enable or disable default route propagation is not user configurable. Once initialized, the unit uses its static default route and does not advertise this route in RIP updates. If another router on your network is configured to advertise its default route, this route overwrites the static default route configured on the unit. The unit then also propagates the new dynamic default route throughout the network. Be aware that, once a dynamic default route is learned, it behaves just as any other dynamic route learned through RIP. This means if the device sending the default route stops sending RIP updates, the default route times out and the unit has no default route to the network. Workarounds for this condition include rebooting or re-entering a static default route. In general, the best approach is to disable the propagation of default routes on the other routers in your network unless you understand the risks. The following table describes the properties and features of each version of RIP supported. RIPv1 RIPv2 RIPv1 Compatible Broadcast Multicast Broadcast No Authentication Authentication Authentication Class routing Classless routing (VLSM) Classless routing (VLSM) 94
Configuration Tsunami MP.11 5012-SUR Installation and Management RIP Parameters (Routing Mode Only) RIPv1 RIPv2 RIPv1 Compatible Distance-vector protocol Distance-vector protocol Distance-vector protocol Metric-Hops Metric-Hops Metric-Hops Maximum Distance 15 Maximum Distance 15 Maximum Distance 15 IGP IGP IGP RIP Example In the following example, assume that both the BSU and the SUs all are configured in Routing mode with RIP enabled to send and receive on both the Ethernet and Wireless interfaces. The network converges through updates until each unit has the following routing table: RIP Notes • Ensure that routers on the same physical network are configured to use the same version of RIP. • Routing updates occur every 30 seconds. It may take up to 3 minutes for a route that has gone down to timeout in a routing table. • RIP is limited to networks with 15 or fewer hops. 95
Page 1 and 2:
Tsunami MP.11 Installation and Mana
Page 3 and 4:
Tsunami MP.11 5012-SUR Installation
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Introduction Tsunami MP.11 5012-SUR
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Installation and Initialization Tsu
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
System Overview Tsunami MP.11 5012-
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44: System Overview Tsunami MP.11 5012-
Page 45 and 46: System Overview Tsunami MP.11 5012-
Page 47 and 48: Tsunami MP.11 5012-SUR Installation
Page 49 and 50: Basic Management Tsunami MP.11 5012
Page 59 and 60: Configuration Tsunami MP.11 5012-SU
Page 93: Configuration Tsunami MP.11 5012-SU
Page 101 and 102: Monitoring Tsunami MP.11 5012-SUR I
Page 117 and 118: Commands Tsunami MP.11 5012-SUR Ins
Page 119 and 120: Commands Tsunami MP.11 5012-SUR Ins
Page 123 and 124: Procedures Tsunami MP.11 5012-SUR I
Page 133 and 134: Troubleshooting Tsunami MP.11 5012-
Page 139 and 140: Country Codes and Channels Tsunami
Page 145 and 146:
Country Codes and Channels Tsunami
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Technical Specifications Tsunami MP
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Technical Services and Support Tsun
Page 161 and 162:
show all

Tsunami MP.11 Installation and Management Model 5012-SUR ...

Create successful ePaper yourself

Delete template?

Save as template?