02 - BTI - We know your business

1006
ProCon X plus
With flange
Without flange
Non-positive anchoring in solid building materials
Positive anchoring in porous stone
Positive anchoring at gypsum board- and light boards
Deep anchoring in gas concrete with ProCon X plus L
(no breaking out at the surface)
�����
Multifunctional dowel ProCon X plus
Allrounder for hollow and solid building materials
g Non-positive anchoring /splaying) in solid building
materials
High contact pressure and large contact surface for
high frictional power by new dowel geometry
g Positive anchoring (knotting) in cavity or in hollow
space or at gypsum board and light boards
Knotting slots led right to the back in pairs result in
excellent knotting characteristics and large contact
surface
g High holding value in solid and hollow material
4x splaying
g High sensitivity for the correct tightening point of
the dowel
g Sure splaying or knotting
High centering and blocking wings as block against
turning
g Easily inserted in borehole
Conical dowel tip
g High value nylon, impact-resistant
High plastic deformation behavior results in large
temperature range for use of -40 to +80 °C; low
sensitivity in dynamic loads
Determining the minimum screw length:
Thickness of object to be fixed
+ dowel length
+ screw dia.
= screw length
Item unit Designation Dim. mm Min. drill drill dia.
number Pieces (dia. x Ld) depth mm (w) mm (fl)
000347 600/2.400 ProCon X plus 5 x 25 w/collar 5 x 25 35 5
000348 400/1.600 ProCon X plus 6 x 35 w/collar 6 x 35 45 6
000349 250/1.000 ProCon X plus 6 x 65 w/collar L 6 x 65 75 6
000350 250/1.000 ProCon X plus 8 x 50 w/collar 8 x 50 60 8
000351 125/ 500 ProCon X plus 8 x 80 w/collar L 8 x 80 90 8
000352 125/ 500 ProCon X plus 10 x 60 w/collar 10 x 60 80 10
000353 600/2.400 ProCon X plus 5 x 25 w/out collar 5 x 30 35 5
000354 400/1.600 ProCon X plus 6 x 35 w/out collar 6 x 35 45 6
000355 250/1.000 ProCon X plus 6 x 65 w/out collar L 6 x 65 75 6
000356 250/1.000 ProCon X plus 8 x 50 w/out collar 8 x 50 60 8
000359 125/ 500 ProCon X plus 8 x 80 w/out collar L 8 x 80 90 8
000362 125/ 500 ProCon X plus 10 x 60 w/out collar 10 x 60 80 10
02-220 A/P/T 02
To obtain optimum working results, the following details should be observed:
Dowel Hollow materials Solid materials
HLZ 12 1) Gypsum board
Chipboard- Wood F rec. Chipboard- Wood F rec. Chipboard- Wood F rec.
screws screws [kN] screws screws [kN] screws screws [kN] 2)
dia. 5 3.0 – 4.0 3.0 – 4.0 0.1 3.0 – 3.5 3.0 – 4.0 0.1 3.0 – 4.0 3.0 – 4.0 0.5
dia. 6 4.0 – 5.0 4.0 – 5.0 0.2 4.0 – 4.5 4.0 – 5.0 0.1 5.0 4.0 – 5.0 0.9
dia. 8 5.0 – 6.0 5.0 – 6.0 0.2 5.0 – 6.0 5.0 – 6.0 0.1 6.0 5.0 – 6.0 1.2
dia. 10 7.0 – 8.0 7.0 – 8.0 0.3 7.0 – 8.0 7.0 – 8.0 0.1 8.0 7.0 – 8.0 1.6
1) Drilling without impact
2) The values indicated apply for use with wooden screws with respectively largest screw diameter
WWW.BTI-GrOuP.COM
02
A
11