ts_125331v120300p

3GPP TS 25.331 version 12.3.0 Release 12
399
ETSI TS 125 331 V12.3.0 (2014-10)
1> select a HS-PDSCH channelisation codes from the list of candidate HS-PDSCH channelisation codes based on
U-RNTI as follows:
"Index of selected HS-PDSCH channelisation codes" = U_RNTI value mod K,
where K is equal to the number of candidate HS-PDSCH channelisation codes.
For 1.28 Mcps TDD, when the IE "Paging associated HS-PDSCH info" is included in the IE "HS-DSCH paging system
information" in System Information Block type 5 and the UE is in CELL_PCH or URA_PCH state, and the variable
HS_DSCH_RECEPTION_GENERAL is set to TRUE, the UE shall select the HS-PDSCH according to the following
rules:
1> compile a list of candidate HS-PDSCH configuration from IE(s) "Paging associated HS-PDSCH info" in the
order of appearance in System Information Block type 5;
1> select an HS-PDSCH configuration from the list of candidate HS-PDSCHs based on U-RNTI as follows:
"Index of selected HS-PDSCH" = U_RNTI value mod K,
where K is equal to the number of candidate HS-PDSCH configuration.
8.5.42 Autonomous UTRAN DRX Cycle length coefficient change
If timer T319 expires:
1> set k to the value of the stored IE "DRX cycle length coefficient";
1> store the result of MAX(2 k ,PBP), where PBP is the Paging Block Periodicity, as the DRX cycle length; and
1> determine its connected mode paging occasions and PICH monitoring occasions in the same way as for idle
mode, according to [4].
NOTE: The DRX cycle length to use in connected mode is defined in [4].
8.5.43 Reception of MBMS from a cell operating in MBSFN mode
A cell provides MBMS service in MBSFN mode if it is indicated so in system information, see subclause 8.1.1.6.3. A
UE that supports MBSFN operation may receive MBMS services via a cell operating in MBSFN mode. For FDD, 3.84
Mcps TDD IMB and 3.84/7.68 Mcps TDD in order to receive an MBMS service via a MBSFN cluster the UE shall
select the MBSFN cluster as specified in [4] in addition to selecting a cell for normal camping as specified in [4]. For
1.28 Mcps TDD in order to receive an MBMS service via an MBSFN cluster the UE shall at the first step camp on a
unicast cell and get the frequency and "cell parameter ID" from the system information, and then get synchronized to
the MBSFN cluster operating with that frequency and "cell parameter ID". For 3.84/7.68 Mcps TDD a cell shall be
considered to be operating in MBSFN mode when individual scrambling codes are assigned to all timeslots (via the IE
"TDD MBSFN Information").
For 3.84 Mcps TDD IMB, MBMS reception is provided on a 3.84 Mcps TDD frequency [22]. The S-CCPCH frame
type 2 format shall be used for the S-CCPCHs carrying MTCH. Unless specified otherwise, the RRC protocol is
operated according to the FDD requirements applicable for MBSFN.
8.5.44 HS-DSCH CQI reporting tables
If the variable HS_DSCH_RECEPTION is set to "TRUE", the UE shall:
1> if the UE has been configured with at least one MAC-ehs reordering queue:
2> use the relevant CQI tables, as defined in [29], for the HS-DSCH category indicated by the IE "HS-DSCH
physical layer category extension" or "HS-DSCH physical layer category extension2" or "HS-DSCH physical
layer category extension3" or "HS-DSCH physical layer category extension 4" or "HS-DSCH physical layer
category extension 5" or "HS-DSCH physical layer category extension 6" or "HS-DSCH physical layer
category extension 7" stored in the variable UE_CAPABILITY_TRANSFERRED. For 1.28 Mcps TDD, use
the table of transport block size, as defined in [15], for the HS-DSCH category indicated by the IE "HS-
DSCH physical layer category extension" stored in the variable UE_CAPABILITY_TRANSFERRED.
ETSI