HP ProCurve Wireless Access Point 420 - Hewlett Packard

More documents

Recommendations

Info

Access Point Configuration Configuring Wireless Security 5-58 ■ Broadcast Key Refresh Rate: Sets the interval at which the broadcast keys are refreshed for stations using 802.1x dynamic keying. (Range: 0 - 1440 minutes; Default: 0 = disabled) ■ Session Key Refresh Rate: The interval at which the access point refreshes unicast session keys for associated clients. (Range: 0 - 1440 minutes; Default: 0 = disabled) ■ 802.1x Reauthentication Refresh Rate: The time period after which a connected client must be re-authenticated. During the re-authentication process of verifying the client credentials on the RADIUS server, the client remains connected the network. Only if re-authentication fails is network access blocked. (Range: 0-65535 seconds; Default: 0 = Disabled) To Configure 802.1x Authentication and Key Management: 1. Select the Configuration tab. 2. Click the [Radius] button. 3. Configure parameters for the primary RADIUS server and, optionally, a secondary RADIUS server. See “Web: Setting RADIUS Server Parameters” on page 5-28 for more details. 4. Click the [Apply Changes] button. 5. Select the Security tab. 6. Click the [Shared Key Setup] button. 7. Set the Authentication Type Setup to Open System. 8. Click the [Apply Changes] button. 9. Click the [Authentication] button. 10. Under 802.1x Setup, select Required. 11. For the Broadcast Key Refresh Rate, enter a time period between 0 (disabled) and 1440 minutes. 12. For the Session Key Refresh Rate, enter a time period between 0 (disabled) and 1440 minutes. 13. For the 802.1x Re-Authentication Refresh Rate, enter a time period between 0 (disabled) and 65535 seconds. 14. Click the [Apply Changes] button.
Figure 5-13. The Authentication Window 802.1x Setup CLI: Configuring IEEE 802.1x CLI Commands Used in This Section Command Syntax CLI Reference Page interface authentication [no] 802.1x 802.1x broadcast-key-refresh-rate 802.1x session-key-refresh-rate 802.1x session-timeout show authentication page 6-53 page 6-66 page 6-40 page 6-41 page 6-41 page 6-42 page 6-46 Access Point Configuration Configuring Wireless Security 5-59
Page 1 and 2:
HP ProCurve Wireless Access Point 4
Page 3 and 4:
Contents 1 Getting Started Contents
Page 5 and 6:
Modifying System Management Access
Page 7 and 8:
sntp-server date-time . . . . . . .
Page 9:
shutdown . . . . . . . . . . . . .
Page 12 and 13:
Getting Started Introduction 1-2 In
Page 14 and 15:
Getting Started Related Publication
Page 16 and 17:
Getting Started Sources for More In
Page 18 and 19:
Getting Started Need Only a Quick S
Page 20 and 21:
Selecting a Management Interface Ov
Page 22 and 23:
Selecting a Management Interface Ad
Page 24 and 25:
Using the Command Line Interface (C
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Using the HP Web Browser Interface
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Access Point Configuration Overview
Page 60 and 61:
Access Point Configuration Modifyin
Page 62 and 63:
Access Point Configuration Modifyin
Page 64 and 65: Access Point Configuration Modifyin
Page 66 and 67: Access Point Configuration Configur
Page 74 and 75: Access Point Configuration Enabling
Page 76 and 77: Access Point Configuration Enabling
Page 88 and 89: Access Point Configuration Setting
Page 124 and 125: Command Line Reference Overview 6-2
Page 126 and 127: Command Line Reference General Comm
Page 128 and 129: Command Line Reference General Comm
Page 130 and 131: Command Line Reference System Manag
Page 148 and 149: Command Line Reference SNMP Command
Page 150 and 151: Command Line Reference SNMP Command
Page 152 and 153: Command Line Reference Flash/File C
Page 154 and 155: Command Line Reference Flash/File C
Page 156 and 157: Command Line Reference RADIUS Clien
Page 162 and 163: Command Line Reference 802.1x Port
Page 164 and 165:
Command Line Reference 802.1x Port
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Command Line Reference Filtering Co
Page 172 and 173:
Command Line Reference Filtering Co
Page 174 and 175:
Command Line Reference Interface Co
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Command Line Reference VLAN Command
Page 202 and 203:
Command Line Reference VLAN Command
Page 204 and 205:
File Transfers Overview A-2 Overvie
Page 206 and 207:
File Transfers Downloading Access P
Page 208 and 209:
File Transfers Downloading Access P
Page 210 and 211:
File Transfers Transferring Configu
Page 212 and 213:
File Transfers Transferring Configu
Page 214 and 215:
P password … 4-7, 4-8 administrat
show all

HP ProCurve Wireless Access Point 420 - Hewlett Packard

Create successful ePaper yourself

Delete template?

Save as template?