HP ProCurve Wireless Access Point 420 - Hewlett Packard

More documents

Recommendations

Info

Command Line Reference VLAN Commands Command Usage The current 802.11 standard does not specify the signaling required between access points in order to support clients roaming from one access point to another. In particular, this can create a problem for clients roaming between access points from different vendors. This command is used to enable or disable 802.11f handover signaling between different access points, especially in a multi-vendor environment. Example HP420(config)#iapp HP420(config)# VLAN Commands The access point can enable the support of VLAN-tagged traffic passing between wireless clients and the wired network. Up to 64 VLAN IDs can be mapped to specific wireless clients, allowing users to remain within the same VLAN as they move around a campus site. When VLAN is enabled on the access point, a VLAN ID (a number between 1 and 4095) can be assigned to each client after successful authentication using IEEE 802.1x and a central RADIUS server. The user VLAN IDs must be configured on the RADIUS server for each user authorized to access the network. If a user does not have a configured VLAN ID, the access point assigns the user to its own configured native VLAN ID. Not e When VLANs are enabled, the access point’s Ethernet interface drops all received traffic that does not include a VLAN tag. To maintain network connectivity to the access point and wireless clients, be sure that the access point is connected to a device port that supports IEEE 802.1Q VLAN tags. 6-78 The VLAN commands supported by the access point are listed below. Command Function Mode Page vlan enable Enables VLAN-tag support for all traffic GC 6-79 native-vlanid Configures the native VLAN for the access point GC 6-79
vlan Command Line Reference VLAN Commands This command enables VLAN-tag support for all traffic. Use the no form to disable VLANs. Syntax vlan enable no vlan Default Disabled Command Mode Global Configuration Example HP420(config)#vlan enable Reboot system now? : y native-vlanid This command configures the native VLAN ID for the access point. Syntax native-vlanid vlan-id - Native VLAN ID. (Range: 1-64) Default Setting 1 Command Mode Global Configuration Command Usage When VLANs are enabled on the access point, a VLAN ID (a number between 1 and 4095) can be assigned to each client after successful authentication using IEEE 802.1x and a central RADIUS server. If a user does not have a configured VLAN ID, the access point assigns the user to its own configured native VLAN ID (a number between 1 and 64). 6-79
Page 1 and 2:
HP ProCurve Wireless Access Point 4
Page 3 and 4:
Contents 1 Getting Started Contents
Page 5 and 6:
Modifying System Management Access
Page 7 and 8:
sntp-server date-time . . . . . . .
Page 9:
shutdown . . . . . . . . . . . . .
Page 12 and 13:
Getting Started Introduction 1-2 In
Page 14 and 15:
Getting Started Related Publication
Page 16 and 17:
Getting Started Sources for More In
Page 18 and 19:
Getting Started Need Only a Quick S
Page 20 and 21:
Selecting a Management Interface Ov
Page 22 and 23:
Selecting a Management Interface Ad
Page 24 and 25:
Using the Command Line Interface (C
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Using the HP Web Browser Interface
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Access Point Configuration Overview
Page 60 and 61:
Access Point Configuration Modifyin
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Access Point Configuration Configur
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Access Point Configuration Enabling
Page 76 and 77:
Access Point Configuration Enabling
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Access Point Configuration Setting
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Command Line Reference Overview 6-2
Page 126 and 127:
Command Line Reference General Comm
Page 128 and 129:
Command Line Reference General Comm
Page 130 and 131:
Command Line Reference System Manag
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Command Line Reference SNMP Command
Page 150 and 151: Command Line Reference SNMP Command
Page 152 and 153: Command Line Reference Flash/File C
Page 154 and 155: Command Line Reference Flash/File C
Page 156 and 157: Command Line Reference RADIUS Clien
Page 162 and 163: Command Line Reference 802.1x Port
Page 170 and 171: Command Line Reference Filtering Co
Page 172 and 173: Command Line Reference Filtering Co
Page 174 and 175: Command Line Reference Interface Co
Page 202 and 203: Command Line Reference VLAN Command
Page 204 and 205: File Transfers Overview A-2 Overvie
Page 206 and 207: File Transfers Downloading Access P
Page 208 and 209: File Transfers Downloading Access P
Page 210 and 211: File Transfers Transferring Configu
Page 212 and 213: File Transfers Transferring Configu
Page 214 and 215: P password … 4-7, 4-8 administrat
show all

HP ProCurve Wireless Access Point 420 - Hewlett Packard

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?