DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

More documents

Recommendations

Info

DOE-STD-I090-96 (Rev-I)Table 9-3. Safe workma distance from Dower mesoa. When operating near high-voltage power lines:rNormal voltage(phase to phase)Minimum requiredclearanceto 50 kV 10ft ~ 3.1 m~Over 50 to 200 kV 15 ft 4.6 mOver 200 to 350 kV 20 ft ( 6.1 m)Over 350 to 500 kV 25 ft ( 7.6 m)Over 500 to 750 kV 35ft ~10.7m~Over 750 to 1000 kV 45 ft 13.7 mb. While in transit with no load and boom or mast lowered:Normal voltage(phase to phase)Minimum requiredclearanceto 0.75 kV 4 ft (1.2 m)Over 0.75 to 50 kV 6 ft ~1.3 m~Over 50 to 345 kV 10 ft 3.5 mOver 345 to 700 kV 16 ft (4.9 m)Over 750 to 1000 kV 20 ft (6.1 m)9-17Chapter 9Mobile Cranes
DOE-STD-1090-96 (Rev-1)c. Durable signs shall be installed at theoperator's station and on the outside ofthecrane,warning that electrocution or serious bodily injurymay occur unless a minimum clearance of 10 ft(3.1 m) is maintained between the crane or theload being handled and energized power lines.Greater clearances are required because ofhighervoltage as stated in Table 9-3. These signs shallbe revised but not removed when a localjurisdiction requires greater clearances.d. Exercise caution when working nearoverhead lines having long spans as they tend tomove laterally or vertically due to the wind, whichcould cause them to breach the safety zone.e. Cranes shall not be used to handlematerials stored under electric power lines unlessany combination ofthe boom, load, load line, ormachine component cannot enter the prohibitedzone.f. Crane operators shall not rely on thecoverings ofwires for their protection.9.5.2.1 Crane Operation NearDe-energized and GroundedElectric Power LinesThis is the preferred condition under which theoperation can be performed safely. The hazard ofinjury or death due to electrocution has beenremove. The following steps shall be taken toassure de-energization ofthe power lines hasoccurred:a. Thepower company or owner of thepower lines shall de-energize the lines.b. The lines shall be visibly grounded toavoid electrical feedback and appropriatelymarked at the job-site location.c. A qualified representative ofthe owner ofthe lines or a designated representative oftheelectrical utility shall be on site to verify that steps(a) and (b) have been completed and that the linesare not energized.9.5.2.2 Power Lines Energized, CraneOperating Less thanErected/Fully Extended BoomLength away from theProhibited Zone(see Figure 9-3)a. An on-site meeting between projectmanagement and a qualified representative of theowner ofthe lines or a designated representativeofthe electrical utility shall take place to establishthe procedures to safely complete the operations.b. The specified clearance between thepower lines and the crane, load line, and load shallbe maintained at all times as specified in Table 93.c. Load control, when required, shall utilizetag lines ofa non~conductive type.d. A designated signaler, whose soleresponsibility is to verify that the requiredclearance is maintained shall be in constantcontact with the crane operator.e. No one shall be permitted to touch thecrane or the load unless the designated signalerindicates it is safe to do so.f. Operation ofboom and load over electricpower lines is extremely dangerous, due toperception of distance and multiple contact pointsas viewed from the position of the operator and lorposition ofthe designated signaler. The operatorshould avoid operating the crane, with or withouta load, in this area.g. The horizontal and vertical distance ofmovement oflong span lines due to the wind shallbe added to the minimum clearance distance asspecified in Table 9-3. A qualified representativeof the the owner of the lines or a designatedrepresentative ofthe electrical utility shall beconsulted for specific distances.h. Devices such as ribbons, balls, etc.,should be attached by a qualified person to thepower lines to improve visibility, or equivalentmeans employed to aid in location oftheprohibited zone.9.5.2.3 Crane Operations are Within theProhibited Zone and the PowerLines are Energizeda. Before such operations take place, aqualified person together with a qualifiedrepresentative of the utility or an engineerqualified in power line transmission shall, aftervisiting the site, determine if this is the mostfeasible way to complete the operation, and setminimum required clearances and procedures forsafe operations. These operations shall be undertheir supervision.The following guidelines should be required:Chapter 9Mobile Cranes 9-18
Page 1 and 2:
INCH-POUNDDOE STANDARDDOE-STD-1 090
Page 3:
DISCLAIMERPortions of this document
Page 7 and 8:
DOE-STD-I090-96 (Rev-I)7.5.6 Attach
Page 9 and 10:
DOE-STD-I090-96 (Rev-I)9.2.6.3 Hydr
Page 11 and 12:
DOE-STD-1090-96 (Rev-l)11.2.3.1 6 x
Page 13 and 14:
DOE-STD-1090-96 (Rev-l)13.4.5 Disco
Page 15 and 16:
DOE-STD-I090-96 (Rev-I)15.4.2 Mobil
Page 18 and 19:
DOE-STD-I090-96 (Rev-I)History and
Page 20 and 21:
DOE-STD-I090-96 (Rev-I)Acknowledgme
Page 22 and 23:
DOE-STD-I090-96 (Rev-I)Introduction
Page 24 and 25:
DOE-STD-I090-96 (Rev-I)CHAPTER 1TER
Page 26 and 27:
DOE-STD-I090-96 (Rev-I)CLOSING LINE
Page 28 and 29:
DOE-STD-I090-96 (Rev-I)END CONTROL:
Page 30 and 31:
LIFT, PREENGINEERED PRODUCTION:Repe
Page 32 and 33:
QUALIFIED ENGINEER/QUALIFIEDENGINEE
Page 35 and 36:
DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 37 and 38:
-----------------------------------
Page 39 and 40:
DOE-STD-I090-96 (Rev-I)2.2 CRITICAL
Page 41 and 42:
DOE-STD-1090-96 (Rev-1)INTENTIONALL
Page 43 and 44:
DOE-STD-I090-96 (Rev-I)3.2 OPERATIO
Page 45 and 46:
DOE-STD-I090-96 (Rev-I)2. Perform a
Page 47 and 48:
DOE-STD-I090-96 (Rev-I)3.4.4 Approv
Page 49 and 50:
DOE-STD-I090-96 (Rev-I)3.6 TRAINING
Page 51 and 52:
Page 53 and 54:
DOE-STD-I090-96 (Rev-I)that create
Page 55 and 56:
4.3 OVERHEAD CRANESDOE-STD-I090-96
Page 57 and 58:
DOE-STD-I090-96 (Rev-I)lNTENTIONAIL
Page 59 and 60:
Page 61 and 62:
DOE-STD-I090-96 (Rev-I)5.2 HOSTILE
Page 63 and 64:
DOE-STD-1090-96 (Rev-l)EXHIBIT IHOS
Page 65 and 66:
Page 67 and 68:
6.2 QUALIFICATIONDOE-STD-I090-96 (R
Page 69 and 70:
6.2.5Operators of ForkliftTrucksa.
Page 71 and 72:
DOE-STD-I090-96 (Rev-I)6.3 TRAINING
Page 73 and 74:
DOE-STD-1090-96 (Rev-l)24. Records
Page 75 and 76:
6.4 REQUALIFICATIONDOE-STD-I090-96
Page 77 and 78:
-----------------------------------
Page 79 and 80:
-----------------------------------
Page 81 and 82:
DOE-STD-I090-96 (Rev-!)Gantry Crane
Page 83 and 84:
DOE-STD-I090-96 (Rev-I)Crane bridge
Page 85 and 86:
DOE-STD-I090-96 (Rev-I)7.2 INSPECTI
Page 87 and 88:
DOE-STD-I090-96 (Rev-I)h. Chain-dri
Page 89 and 90:
DOE-STD-I090-96 (Rev-I)trouble pers
Page 91 and 92: DOE-STD-I090-96 (Rev-I)7.4 MAINTENA
Page 93 and 94: DOE-STD-I090-96 (Rev-I)HOIST. With
Page 95 and 96: DOE-STD-I090-96 (Rev-I)g. Do not lo
Page 97 and 98: DOE-STD-1090-96 (Rev-l). IN1ENTIONA
Page 99 and 100: DOE-STD-1090-96 (Rev-l)EXHIBIT I (c
Page 101 and 102: DOE-STD-I090-96 (Rev-I)EXHIBIT I (c
Page 103 and 104: DOE-STD-I090-96 (Rev-I)8.3 TESTING
Page 105 and 106: DOE-STD-I090-96 (Rev-I)Figure 8-3.
Page 107 and 108: DOE-STD-I090-96 (Rev-I)8.1.1Operato
Page 109 and 110: DOE-STD-I090-96 (Rev-I)operating co
Page 111 and 112: DOE-STD-I090-96 (Rev-I)8.2 INSPECTI
Page 113 and 114: DOE-STD-I090-96 (Rev-I)2. A number
Page 115 and 116: DOE-STD-!090-96 (Rev-!)iv.Inspect f
Page 119 and 120: DOE-STD-I090-96 (Rev-I)d. Do not op
Page 121 and 122: DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 125 and 126: DOE-STD-I090-96 (Rev-I)9.5.29.5.39.
Page 127 and 128: DOE-STD-I090-96 (Rev-I)Table 9-1. S
Page 129 and 130: DOE-STD-1090-96 (Rev-1)r-1r.ilE3...
Page 131 and 132: DOE-STD-I090-96 (Rev-I)9.2 INSPECTI
Page 133 and 134: DOE-STD-I090-96 (Rev-I)d. Evidence
Page 135 and 136: DOE-STD-I090-96 (Rev-I)before retur
Page 139 and 140: DOE-STD-I090-96 (Rev-!)t. Lock carr
Page 141: DOE-STD-I090-96 (Rev-I)Figure 9-2.
Page 145 and 146: DOE-STD-I090-96 (Rev-I)1. Cranel10a
Page 147 and 148: DOE-STD-I090-96 (Rev-I)IIIIIIIIIIII
Page 149 and 150: DOE·STD·I090·96 (Rev-I)HOIST. Wi
Page 151 and 152: DOE-STD-I090-96 (Rev-I)RETRACT 800M
Page 153 and 154: DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 159 and 160: DOE-STD-1090-96 (Rev-1)10.5.5 Movin
Page 161 and 162: DOE-STD-I090-96 (Rev-I)10.1.6 Modif
Page 163 and 164: DOE-STD-I090-96 (Rev-I)1. Class I-l
Page 165 and 166: DOE-STD-I090-96 (Rev-I)CAUTIONONLY
Page 167 and 168: -- ----------------------------10.4
Page 169 and 170: DOE-STD-1090-96 (Rev-l)20. To avoid
Page 171 and 172: DOE-STD-1090-96 (Rev-1)RAISE THE TI
Page 173 and 174: -- -----------DOE-STD-I090-96 (Rev-
Page 177 and 178: DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 179 and 180: DOE-STD-1090-96 (Rev-l)Table 11-1.
Page 181 and 182: DOE-STD-I090-96 (Rev-I)11.2 WIRE RO
Page 183 and 184: -~ --~---------------------------DO
Page 185 and 186: DOE-STD-I090-96 (Rev-I)11.3 SLINGS1
Page 187 and 188: DOE-STD-1090-96 (Rev-1)11.3.1.3 Des
Page 189 and 190: DOE-STD-I090-96 (Rev-I)Table 11-4.
Page 191 and 192: DOE-STD-I090-96 (Rev-I)Table 11-6.
Page 193 and 194:
DOE-STD-1090-96 (Rev-l)Table 11-8.
Page 195 and 196:
DOE-STD-I090-96 (Rev-I)Angle of cho
Page 197 and 198:
DOE-STD-I090-96 (Rev-I)temperatures
Page 199 and 200:
DOE-STD-I090-96 (Rev-!)7. Locate sl
Page 201 and 202:
-------------------DOE-STD-I090-96
Page 203 and 204:
-_.._-----~------------DOE-STD-I090
Page 205 and 206:
DOE-STD-I090-96 (Rev-I)Table 11-13.
Page 207 and 208:
DOE·STD·I090·96 (Rev-I)q. Never
Page 209 and 210:
DOE-STD-I090-96 (Rev-I)j. Despite t
Page 211 and 212:
DOE-STD-I090-96 (Rev-I)Table 11-14.
Page 213 and 214:
DOE·STD·1090-96 (Rev-1)certificat
Page 215 and 216:
DOE-STD-I090-96 (Rev-I)Exhibits I t
Page 217 and 218:
DOE-STD-1090-96 (Rev-l)lNTENTIONALL
Page 219 and 220:
------DOE-STD-I090-96 (Rev-I)EXHIBI
Page 221 and 222:
Page 223 and 224:
DOE-STD-1090-96 (Rev-l)INTENTIONALL
Page 225 and 226:
-----------------------------------
Page 227 and 228:
DOE-STD-I090-96 (Rev-I)Good and Bad
Page 229 and 230:
12.2 RIGGING HOOKSDOE-STD-I090-96 (
Page 231 and 232:
DOE-STD-I090-96 (Rev-I)2. Heavy ser
Page 233 and 234:
DOE-STD-I090-96 (Rev-I)Typical shac
Page 235 and 236:
DOE-STD-I090-96 (Rev-I)• Shoulder
Page 237 and 238:
12.5 TURNBUCKLESDOE-STD-I090-96 (Re
Page 239 and 240:
12.6 LINKS AND RINGSDOE-STD-I090-96
Page 241 and 242:
DOE-STD-I090-96 (Rev-I)12.7 METAL-P
Page 243 and 244:
DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 245 and 246:
---------------------------DOE-STD-
Page 247 and 248:
Page 249 and 250:
DOE-STD-1090-96 (Rev-l)13.2 INSPECT
Page 251 and 252:
DOE-STD-I090-96 (Rev-I)13.3 TESTING
Page 253 and 254:
DOE-STD-1090-96 (Rev-l)13.4 NONDEST
Page 255 and 256:
-------------------------------~--1
Page 257 and 258:
-----------------------------------
Page 259 and 260:
DOE-STD-1090-96 (Rev-1)14.4.4.3 Per
Page 261 and 262:
DOE-STD-I090-96 (Rev-I)14.2 STRUCTU
Page 263 and 264:
.----------------------------------
Page 265 and 266:
DOE-STD-I090-96 (Rev-I)14.2.7 Maint
Page 267 and 268:
DOE-STD-I090-96 (Rev-!)Four-pad pow
Page 269 and 270:
DOE-STD-I090-96 (Rev-I)14.3.5 Testi
Page 271 and 272:
DOE-STD-I090-96 (Rev-I)14.4 MAGNETS
Page 273 and 274:
DOE-STD-I090-96 (Rev-I)1. External
Page 275 and 276:
DOE-STD-I090-96 (Rev-I)instructed b
Page 277 and 278:
- ---------------------------------
Page 279 and 280:
DOE-STD-I090-96 (Rev-I)6. Charging
Page 281 and 282:
DOE-STD-!090-96 (Rev-!)EXHIBIT IPag
Page 283 and 284:
-------------------~---------------
Page 285 and 286:
DOE·STD·I090-96 (Rev-I)15.2 DEFIN
Page 287 and 288:
General note for Figures 15-5 throu
Page 289 and 290:
DOE-STD-I090-96 (Rev-I)LIFT, ORDINA
Page 291 and 292:
DOE-STD-1090~96 (Rev-l)Consideratio
Page 293 and 294:
DOE-STD-I090-96 (Rev-I)15.4.2.4 Fre
Page 295 and 296:
DOE-STD-I090-96 (Rev-I)4. Corroded
Page 297 and 298:
DOE-STD-I090-96 (Rev-I)attention to
Page 299 and 300:
DOE-STD-I090-96 (Rev-I)b. Test load
Page 301 and 302:
DOE-STD-!090-96 (Rev-!)regardless Q
Page 303 and 304:
DOE-STD-1090-96 (Rev-1)EMERGENCY ST
Page 305 and 306:
DOE-STD-I090-96 (Rev-I)so by an app
Page 307 and 308:
DOE-STD-I090-96 (Rev-I)Figure 15-13
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
DOE-STD-I090-96 (Rev-I)include the
Page 315 and 316:
DOE-STD-1090-96 (Rev-l)the platform
Page 317 and 318:
DOE-STD-I090-96 (Rev-I)h. Report an
Page 319 and 320:
DOE-STD-!090-96 (Rev-!)fRAISE THE T
Page 321 and 322:
DOE-STD-I090-96 (Rev-I)h. Provide 4
Page 323 and 324:
DOE-STD-1090-96 (Rev-l)ASME B56.7,
Page 325 and 326:
show all

DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

Create successful ePaper yourself

Delete template?

Save as template?