DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

More documents

Recommendations

Info

DOE·STD·1090-96 (Rev-l)When legs are notof equal length, usesmaflest H/[ ratioNOTE: Load may be supportedon only 2 legs while 3rd legbalances it. Therefore, ther~uired SWL is determined bythe following:Total Rated Capacity = WLL(of single vertical hitch) x H/L x 2Figure 11-8. Determination of capacity---3-leg bridle sling.When legs are not of equal length,use smanest HlL ratio.NOTE: Load may be carried by only 2 legswhile other 2 legs balance it. Therefore.the required SWL is determined by the .following:Total Rated Capacity =WLL (of singlevertical hitch) x H/L x 2Figure 11-9. Determination of capacity-4-leg bridle sling.11-11Chapter 11Wire Rope and Slings
DOE-STD-I090-96 (Rev-I)Table 11-4. Load capacity of wire-rope slings.Hand tuck splice (IWRC) in pounds Design Factor =5:10 0Iit'1\: :; •_orhRllqs0 ~Basket orDia in inches Vertical Choker two leas Dia in inchesU 1\ *t_·rM>ltp ~ 11,*.. "'twol~ ~1/4 1,100 820 2,200 1,800 1,500 1,100 1/45/16 1,600 1,280 3.200 2,800 2,200 1,600 5/163/8 2,400 1,840 4,800 4,000 3,200 2,400 3/87/16 3,000 2,400 6,000 5,400 4,400 3,000 7/16*4,000 3,200 8,000 6,800 5,600 4,0009/16 5,000 4,000 10,000 8,600 7,000 5,000 9/165/8 6,000 5,000 12,000 10,400 8,400 6,000 5/83/4 8,400 7,200 16,800 14,600 11,800 8,400 3/47/8 11,000 9,600 22,000 19,200 15,600 11,000 7/81 14,000 12,600 28,000 24,000 20,000 14,000 111/8 18,000 15,800 36,000 32,000 26,000 18,000 11/8*11/4 22,000 19,400 44,000 36,000 30,000 22,000 *11/4*13/8 26,000 24,000 52,000 44,000 36,000 26,000 *13/8*1 * 32,000 28,000 64,000 52,000 42,000 32,000 *1 **15/8 36,000 32,000 72,000 62,000 50,000 36,000 *15/8*13/4 42.000 38,000 84,000 70,000 58,000 42,000 *13/4*2 56,000 48,000 112,000 92,000 74,000 58,000 *2*Notes:Wire RooeI6 x 19 and *6 x 37 IPS IWRC(CFR 1910.184/ANSI/ASME 830.9)(1) These values only apply when the Old ratio is 25 or greater (choker and basket hitches)o = Diameter of curvature around which the body of the sling is bentd = Diameter of rope(2) Choker hitch values apply only to choke angles greater than 120 degrees.Chapter 11Wire Rope and Slings 11-12
Page 1 and 2:
INCH-POUNDDOE STANDARDDOE-STD-1 090
Page 3:
DISCLAIMERPortions of this document
Page 7 and 8:
DOE-STD-I090-96 (Rev-I)7.5.6 Attach
Page 9 and 10:
DOE-STD-I090-96 (Rev-I)9.2.6.3 Hydr
Page 11 and 12:
DOE-STD-1090-96 (Rev-l)11.2.3.1 6 x
Page 13 and 14:
DOE-STD-1090-96 (Rev-l)13.4.5 Disco
Page 15 and 16:
DOE-STD-I090-96 (Rev-I)15.4.2 Mobil
Page 18 and 19:
DOE-STD-I090-96 (Rev-I)History and
Page 20 and 21:
DOE-STD-I090-96 (Rev-I)Acknowledgme
Page 22 and 23:
DOE-STD-I090-96 (Rev-I)Introduction
Page 24 and 25:
DOE-STD-I090-96 (Rev-I)CHAPTER 1TER
Page 26 and 27:
DOE-STD-I090-96 (Rev-I)CLOSING LINE
Page 28 and 29:
DOE-STD-I090-96 (Rev-I)END CONTROL:
Page 30 and 31:
LIFT, PREENGINEERED PRODUCTION:Repe
Page 32 and 33:
QUALIFIED ENGINEER/QUALIFIEDENGINEE
Page 35 and 36:
DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 37 and 38:
-----------------------------------
Page 39 and 40:
DOE-STD-I090-96 (Rev-I)2.2 CRITICAL
Page 41 and 42:
DOE-STD-1090-96 (Rev-1)INTENTIONALL
Page 43 and 44:
DOE-STD-I090-96 (Rev-I)3.2 OPERATIO
Page 45 and 46:
DOE-STD-I090-96 (Rev-I)2. Perform a
Page 47 and 48:
DOE-STD-I090-96 (Rev-I)3.4.4 Approv
Page 49 and 50:
DOE-STD-I090-96 (Rev-I)3.6 TRAINING
Page 51 and 52:
Page 53 and 54:
DOE-STD-I090-96 (Rev-I)that create
Page 55 and 56:
4.3 OVERHEAD CRANESDOE-STD-I090-96
Page 57 and 58:
DOE-STD-I090-96 (Rev-I)lNTENTIONAIL
Page 59 and 60:
Page 61 and 62:
DOE-STD-I090-96 (Rev-I)5.2 HOSTILE
Page 63 and 64:
DOE-STD-1090-96 (Rev-l)EXHIBIT IHOS
Page 65 and 66:
Page 67 and 68:
6.2 QUALIFICATIONDOE-STD-I090-96 (R
Page 69 and 70:
6.2.5Operators of ForkliftTrucksa.
Page 71 and 72:
DOE-STD-I090-96 (Rev-I)6.3 TRAINING
Page 73 and 74:
DOE-STD-1090-96 (Rev-l)24. Records
Page 75 and 76:
6.4 REQUALIFICATIONDOE-STD-I090-96
Page 77 and 78:
-----------------------------------
Page 79 and 80:
-----------------------------------
Page 81 and 82:
DOE-STD-I090-96 (Rev-!)Gantry Crane
Page 83 and 84:
DOE-STD-I090-96 (Rev-I)Crane bridge
Page 85 and 86:
DOE-STD-I090-96 (Rev-I)7.2 INSPECTI
Page 87 and 88:
DOE-STD-I090-96 (Rev-I)h. Chain-dri
Page 89 and 90:
DOE-STD-I090-96 (Rev-I)trouble pers
Page 91 and 92:
DOE-STD-I090-96 (Rev-I)7.4 MAINTENA
Page 93 and 94:
DOE-STD-I090-96 (Rev-I)HOIST. With
Page 95 and 96:
DOE-STD-I090-96 (Rev-I)g. Do not lo
Page 97 and 98:
DOE-STD-1090-96 (Rev-l). IN1ENTIONA
Page 99 and 100:
DOE-STD-1090-96 (Rev-l)EXHIBIT I (c
Page 101 and 102:
DOE-STD-I090-96 (Rev-I)EXHIBIT I (c
Page 103 and 104:
DOE-STD-I090-96 (Rev-I)8.3 TESTING
Page 105 and 106:
DOE-STD-I090-96 (Rev-I)Figure 8-3.
Page 107 and 108:
DOE-STD-I090-96 (Rev-I)8.1.1Operato
Page 109 and 110:
DOE-STD-I090-96 (Rev-I)operating co
Page 111 and 112:
Page 113 and 114:
DOE-STD-I090-96 (Rev-I)2. A number
Page 115 and 116:
DOE-STD-!090-96 (Rev-!)iv.Inspect f
Page 117 and 118:
DOE-STD-I090-96 (Rev-I)8.4 MAINTENA
Page 119 and 120:
DOE-STD-I090-96 (Rev-I)d. Do not op
Page 121 and 122:
DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 123 and 124:
DOE-STD-I090-96 (Rev-I)EXHIBIT I (c
Page 125 and 126:
DOE-STD-I090-96 (Rev-I)9.5.29.5.39.
Page 127 and 128:
DOE-STD-I090-96 (Rev-I)Table 9-1. S
Page 129 and 130:
DOE-STD-1090-96 (Rev-1)r-1r.ilE3...
Page 131 and 132:
Page 133 and 134:
DOE-STD-I090-96 (Rev-I)d. Evidence
Page 135 and 136:
DOE-STD-I090-96 (Rev-I)before retur
Page 137 and 138: DOE-STD-I090-96 (Rev-I)9.4 MAINTENA
Page 139 and 140: DOE-STD-I090-96 (Rev-!)t. Lock carr
Page 141 and 142: DOE-STD-I090-96 (Rev-I)Figure 9-2.
Page 143 and 144: DOE-STD-1090-96 (Rev-1)c. Durable s
Page 145 and 146: DOE-STD-I090-96 (Rev-I)1. Cranel10a
Page 147 and 148: DOE-STD-I090-96 (Rev-I)IIIIIIIIIIII
Page 149 and 150: DOE·STD·I090·96 (Rev-I)HOIST. Wi
Page 151 and 152: DOE-STD-I090-96 (Rev-I)RETRACT 800M
Page 153 and 154: DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 155 and 156: DOE-STD-I090-96 (Rev-I)EXHIBIT I (c
Page 159 and 160: DOE-STD-1090-96 (Rev-1)10.5.5 Movin
Page 161 and 162: DOE-STD-I090-96 (Rev-I)10.1.6 Modif
Page 163 and 164: DOE-STD-I090-96 (Rev-I)1. Class I-l
Page 165 and 166: DOE-STD-I090-96 (Rev-I)CAUTIONONLY
Page 167 and 168: -- ----------------------------10.4
Page 169 and 170: DOE-STD-1090-96 (Rev-l)20. To avoid
Page 171 and 172: DOE-STD-1090-96 (Rev-1)RAISE THE TI
Page 173 and 174: -- -----------DOE-STD-I090-96 (Rev-
Page 177 and 178: DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 179 and 180: DOE-STD-1090-96 (Rev-l)Table 11-1.
Page 181 and 182: DOE-STD-I090-96 (Rev-I)11.2 WIRE RO
Page 183 and 184: -~ --~---------------------------DO
Page 185 and 186: DOE-STD-I090-96 (Rev-I)11.3 SLINGS1
Page 187: DOE-STD-1090-96 (Rev-1)11.3.1.3 Des
Page 191 and 192: DOE-STD-I090-96 (Rev-I)Table 11-6.
Page 193 and 194: DOE-STD-1090-96 (Rev-l)Table 11-8.
Page 195 and 196: DOE-STD-I090-96 (Rev-I)Angle of cho
Page 197 and 198: DOE-STD-I090-96 (Rev-I)temperatures
Page 199 and 200: DOE-STD-I090-96 (Rev-!)7. Locate sl
Page 201 and 202: -------------------DOE-STD-I090-96
Page 203 and 204: -_.._-----~------------DOE-STD-I090
Page 207 and 208: DOE·STD·I090·96 (Rev-I)q. Never
Page 209 and 210: DOE-STD-I090-96 (Rev-I)j. Despite t
Page 213 and 214: DOE·STD·1090-96 (Rev-1)certificat
Page 215 and 216: DOE-STD-I090-96 (Rev-I)Exhibits I t
Page 217 and 218: DOE-STD-1090-96 (Rev-l)lNTENTIONALL
Page 219 and 220: ------DOE-STD-I090-96 (Rev-I)EXHIBI
Page 221 and 222: DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 223 and 224: DOE-STD-1090-96 (Rev-l)INTENTIONALL
Page 225 and 226: -----------------------------------
Page 227 and 228: DOE-STD-I090-96 (Rev-I)Good and Bad
Page 229 and 230: 12.2 RIGGING HOOKSDOE-STD-I090-96 (
Page 231 and 232: DOE-STD-I090-96 (Rev-I)2. Heavy ser
Page 233 and 234: DOE-STD-I090-96 (Rev-I)Typical shac
Page 235 and 236: DOE-STD-I090-96 (Rev-I)• Shoulder
Page 237 and 238: 12.5 TURNBUCKLESDOE-STD-I090-96 (Re
Page 239 and 240:
12.6 LINKS AND RINGSDOE-STD-I090-96
Page 241 and 242:
DOE-STD-I090-96 (Rev-I)12.7 METAL-P
Page 243 and 244:
DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 245 and 246:
---------------------------DOE-STD-
Page 247 and 248:
Page 249 and 250:
DOE-STD-1090-96 (Rev-l)13.2 INSPECT
Page 251 and 252:
DOE-STD-I090-96 (Rev-I)13.3 TESTING
Page 253 and 254:
DOE-STD-1090-96 (Rev-l)13.4 NONDEST
Page 255 and 256:
-------------------------------~--1
Page 257 and 258:
-----------------------------------
Page 259 and 260:
DOE-STD-1090-96 (Rev-1)14.4.4.3 Per
Page 261 and 262:
DOE-STD-I090-96 (Rev-I)14.2 STRUCTU
Page 263 and 264:
.----------------------------------
Page 265 and 266:
DOE-STD-I090-96 (Rev-I)14.2.7 Maint
Page 267 and 268:
DOE-STD-I090-96 (Rev-!)Four-pad pow
Page 269 and 270:
DOE-STD-I090-96 (Rev-I)14.3.5 Testi
Page 271 and 272:
DOE-STD-I090-96 (Rev-I)14.4 MAGNETS
Page 273 and 274:
DOE-STD-I090-96 (Rev-I)1. External
Page 275 and 276:
DOE-STD-I090-96 (Rev-I)instructed b
Page 277 and 278:
- ---------------------------------
Page 279 and 280:
DOE-STD-I090-96 (Rev-I)6. Charging
Page 281 and 282:
DOE-STD-!090-96 (Rev-!)EXHIBIT IPag
Page 283 and 284:
-------------------~---------------
Page 285 and 286:
DOE·STD·I090-96 (Rev-I)15.2 DEFIN
Page 287 and 288:
General note for Figures 15-5 throu
Page 289 and 290:
DOE-STD-I090-96 (Rev-I)LIFT, ORDINA
Page 291 and 292:
DOE-STD-1090~96 (Rev-l)Consideratio
Page 293 and 294:
DOE-STD-I090-96 (Rev-I)15.4.2.4 Fre
Page 295 and 296:
DOE-STD-I090-96 (Rev-I)4. Corroded
Page 297 and 298:
DOE-STD-I090-96 (Rev-I)attention to
Page 299 and 300:
DOE-STD-I090-96 (Rev-I)b. Test load
Page 301 and 302:
DOE-STD-!090-96 (Rev-!)regardless Q
Page 303 and 304:
DOE-STD-1090-96 (Rev-1)EMERGENCY ST
Page 305 and 306:
DOE-STD-I090-96 (Rev-I)so by an app
Page 307 and 308:
DOE-STD-I090-96 (Rev-I)Figure 15-13
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
DOE-STD-I090-96 (Rev-I)include the
Page 315 and 316:
DOE-STD-1090-96 (Rev-l)the platform
Page 317 and 318:
DOE-STD-I090-96 (Rev-I)h. Report an
Page 319 and 320:
DOE-STD-!090-96 (Rev-!)fRAISE THE T
Page 321 and 322:
DOE-STD-I090-96 (Rev-I)h. Provide 4
Page 323 and 324:
DOE-STD-1090-96 (Rev-l)ASME B56.7,
Page 325 and 326:
show all

DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

Create successful ePaper yourself

Delete template?

Save as template?