DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

More documents

Recommendations

Info

DOE-STD-I090-96 (Rev-I)14.3.8 Operationa Only the following personnel shall operatevacuum lifting devices:1. Qualified operators or riggers.2. Trainees under the direct supervisionofa qualified operator.3. Maintenance and test personnel, whenit is necessary in the performance oftheir duties.4. Inspectors oflifting devices.b. The following shall apply to all personnelwho operate vacuum lifting devices:1. Before starting the lift, verify that the"vacuum on" indicator has reached the requiredlevel. Also, verify that the vacuum lifting devicehas been correctly applied and a stable vacuumlevel exists by lifting the load a few inches andobserving conditions.2. Observe the condition ofthe liftingdevice before use and during operation. Ifyouobserve a defect that affects the continued safe useofthe lifting device, remove it from service.3. Place any attached load on the floor orground and, after use, properly store the liftingdevice before leaving.4. Before they are used on a shift, test thelifting device controls. Ifany do not operateproperly, adjust or repair them before operationsbegin.5. Do not load the lifting device in excessofits rated capacity (except for test loads) orhandle any load for which it is not designed.6. Apply the lifting device to the load inaccordance with established procedures.7. Before lifting, ensure thatlifting-device ropes or chains are not kinked andmultiple-part lines are not interwoven.8. Ensure that the load is correctlydistributed for the lifting device being used.9. Do not use the lifting device for sidepulls or sliding the load unless specificallyauthorized by a qualified person or by anapproved procedure.10. Warn all personnel in the vicinity ofthe lifting device and place the load on the floor orground, ifpossible to do so, ifelectrical powergoes off while a load is being lifted.11. Do not leave your position at thecontrols.12. Do not use a lifting device that istagged "Danger-Do Not Operate" or otherwisedesignated as nonfunctional.13. Do not remove "Danger-Do NotOperate" tags from lifting devices without theapproval ofthe person who placed them or anauthorized person.14. Store the lifting device in a dry, insidelocation when not in use.15. Ensure that markings or tags are notremoved or defaced. Replace missing or defacedmarkings or tags.14-11Chapter 14Below-the-Hook Lifting Devices
DOE-STD-I090-96 (Rev-I)14.4 MAGNETS, CLOSE-PROXIMITY-OPERATEDClose-proximity-operated magnetic lifting devicesare used for single- or multiple-steel-piecehandling operations in which the operator ofthemagnet is required to manually guide the loadduring its movement They are also used insituations where remotely operated magnets areoperated close to people. Typicalclose-proximity-operated magnetic lifting devicesare shown inFigure 14-7.14.4.1 Design/FabricationClose-proximity-operated magnetic lifting devicesshall be designed and fabricated in accordancewith the provisions ofASME B30.20, 20-3.2.2and 20-3.2.3.14.4.2 Markinga. At a minimum, a nameplate, name tag, orother permanent marker shall be affIXed to eachlifting magnet, and shall display the followingdata:1. Manufacturer's name, or ifthe magnethas been repaired or modified, the name andaddress ofthe repairer/modifier.2. Model or unit identification.3. Weight.4. Duty cycle, ifapplicable.5. Cold current6. Rated capacity.b. Also, battery-powered and external-poweredlifting electromagnets and electrically controlledpermanent-magnet lifting magnets shall bemarked with:1. The voltage ofthe battery or primarypower supply.2. The cold current or watts at 68 degreesF (20 degrees C) and rated voltage.c. Cases may exist where a lifting devicecannot be marked with its rated capacity andweight. This may be due to the securityclassification ofthe load to be lifted or otherreasons approved by the responsible manager. Inthese cases, the lifting device shall be marked withan identification number, and its documentationshall contain both its rated capacity and weight.d. A label or labels shall be affixed to eachlifting magnet in a readable position that displaysthe word "CAUTION" or other legend designed tobring the label to the attention ofthe operator.The label shall also contain informationcautioning against:1. Operating when the battery capacity isinadequate.2. Exceeding magnet duty cycle anddisconnecting the magnet with the power on (forexternally powered electromagnets).3. Operating ifthe internal controlfunction indicator, where applicable, does notindicate a complete cycle (on electricallycontrolled permanent magnets).4. Operating with the control handle notfully in the "Lift" position (on manually controlledpermanent magnets).14.4.2.1 Rated load (Capacity)a. General-application magnets shall includethe rated load (capacity) ofthe magnet on thelifting magnet or on a tag attached to it Thiscapacity rating shall refer to the instructionmanual for information relating to decreases inrating due to the load surface condition, thickness,percentage ofcontact with magnet, temperature,metallurgical composition, and deflection.b. Specified-application magnets shall includethe application load (capacity) ofthe magnet onthe lifting magnet or on a tag attached to it. Thiscapacity rating shall refer to the specific loads forwhich it applies.14.4.2.2 ControlsThe position ofthe control switch or handle ofalifting magnet shall be marked with "Lift," "Off,"and "Drop," or equivalent terms indicating themode ofoperation ofthe lifting magnet.14.4.3 Installationa. Close-proxirnity-operated magnetic liftingdevices shall be installed according to themanufacturer's recommendations.b. Users shall ensure that:Chapter 14Below-the-Hook Lifting Devices 14-12
Page 1 and 2:
INCH-POUNDDOE STANDARDDOE-STD-1 090
Page 3:
DISCLAIMERPortions of this document
Page 7 and 8:
DOE-STD-I090-96 (Rev-I)7.5.6 Attach
Page 9 and 10:
DOE-STD-I090-96 (Rev-I)9.2.6.3 Hydr
Page 11 and 12:
DOE-STD-1090-96 (Rev-l)11.2.3.1 6 x
Page 13 and 14:
DOE-STD-1090-96 (Rev-l)13.4.5 Disco
Page 15 and 16:
DOE-STD-I090-96 (Rev-I)15.4.2 Mobil
Page 18 and 19:
DOE-STD-I090-96 (Rev-I)History and
Page 20 and 21:
DOE-STD-I090-96 (Rev-I)Acknowledgme
Page 22 and 23:
DOE-STD-I090-96 (Rev-I)Introduction
Page 24 and 25:
DOE-STD-I090-96 (Rev-I)CHAPTER 1TER
Page 26 and 27:
DOE-STD-I090-96 (Rev-I)CLOSING LINE
Page 28 and 29:
DOE-STD-I090-96 (Rev-I)END CONTROL:
Page 30 and 31:
LIFT, PREENGINEERED PRODUCTION:Repe
Page 32 and 33:
QUALIFIED ENGINEER/QUALIFIEDENGINEE
Page 35 and 36:
DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 37 and 38:
-----------------------------------
Page 39 and 40:
DOE-STD-I090-96 (Rev-I)2.2 CRITICAL
Page 41 and 42:
DOE-STD-1090-96 (Rev-1)INTENTIONALL
Page 43 and 44:
DOE-STD-I090-96 (Rev-I)3.2 OPERATIO
Page 45 and 46:
DOE-STD-I090-96 (Rev-I)2. Perform a
Page 47 and 48:
DOE-STD-I090-96 (Rev-I)3.4.4 Approv
Page 49 and 50:
DOE-STD-I090-96 (Rev-I)3.6 TRAINING
Page 51 and 52:
Page 53 and 54:
DOE-STD-I090-96 (Rev-I)that create
Page 55 and 56:
4.3 OVERHEAD CRANESDOE-STD-I090-96
Page 57 and 58:
DOE-STD-I090-96 (Rev-I)lNTENTIONAIL
Page 59 and 60:
Page 61 and 62:
DOE-STD-I090-96 (Rev-I)5.2 HOSTILE
Page 63 and 64:
DOE-STD-1090-96 (Rev-l)EXHIBIT IHOS
Page 65 and 66:
Page 67 and 68:
6.2 QUALIFICATIONDOE-STD-I090-96 (R
Page 69 and 70:
6.2.5Operators of ForkliftTrucksa.
Page 71 and 72:
DOE-STD-I090-96 (Rev-I)6.3 TRAINING
Page 73 and 74:
DOE-STD-1090-96 (Rev-l)24. Records
Page 75 and 76:
6.4 REQUALIFICATIONDOE-STD-I090-96
Page 77 and 78:
-----------------------------------
Page 79 and 80:
-----------------------------------
Page 81 and 82:
DOE-STD-I090-96 (Rev-!)Gantry Crane
Page 83 and 84:
DOE-STD-I090-96 (Rev-I)Crane bridge
Page 85 and 86:
DOE-STD-I090-96 (Rev-I)7.2 INSPECTI
Page 87 and 88:
DOE-STD-I090-96 (Rev-I)h. Chain-dri
Page 89 and 90:
DOE-STD-I090-96 (Rev-I)trouble pers
Page 91 and 92:
DOE-STD-I090-96 (Rev-I)7.4 MAINTENA
Page 93 and 94:
DOE-STD-I090-96 (Rev-I)HOIST. With
Page 95 and 96:
DOE-STD-I090-96 (Rev-I)g. Do not lo
Page 97 and 98:
DOE-STD-1090-96 (Rev-l). IN1ENTIONA
Page 99 and 100:
DOE-STD-1090-96 (Rev-l)EXHIBIT I (c
Page 101 and 102:
DOE-STD-I090-96 (Rev-I)EXHIBIT I (c
Page 103 and 104:
DOE-STD-I090-96 (Rev-I)8.3 TESTING
Page 105 and 106:
DOE-STD-I090-96 (Rev-I)Figure 8-3.
Page 107 and 108:
DOE-STD-I090-96 (Rev-I)8.1.1Operato
Page 109 and 110:
DOE-STD-I090-96 (Rev-I)operating co
Page 111 and 112:
Page 113 and 114:
DOE-STD-I090-96 (Rev-I)2. A number
Page 115 and 116:
DOE-STD-!090-96 (Rev-!)iv.Inspect f
Page 117 and 118:
Page 119 and 120:
DOE-STD-I090-96 (Rev-I)d. Do not op
Page 121 and 122:
DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 123 and 124:
Page 125 and 126:
DOE-STD-I090-96 (Rev-I)9.5.29.5.39.
Page 127 and 128:
DOE-STD-I090-96 (Rev-I)Table 9-1. S
Page 129 and 130:
DOE-STD-1090-96 (Rev-1)r-1r.ilE3...
Page 131 and 132:
Page 133 and 134:
DOE-STD-I090-96 (Rev-I)d. Evidence
Page 135 and 136:
DOE-STD-I090-96 (Rev-I)before retur
Page 137 and 138:
Page 139 and 140:
DOE-STD-I090-96 (Rev-!)t. Lock carr
Page 141 and 142:
DOE-STD-I090-96 (Rev-I)Figure 9-2.
Page 143 and 144:
DOE-STD-1090-96 (Rev-1)c. Durable s
Page 145 and 146:
DOE-STD-I090-96 (Rev-I)1. Cranel10a
Page 147 and 148:
DOE-STD-I090-96 (Rev-I)IIIIIIIIIIII
Page 149 and 150:
DOE·STD·I090·96 (Rev-I)HOIST. Wi
Page 151 and 152:
DOE-STD-I090-96 (Rev-I)RETRACT 800M
Page 153 and 154:
DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
DOE-STD-1090-96 (Rev-1)10.5.5 Movin
Page 161 and 162:
DOE-STD-I090-96 (Rev-I)10.1.6 Modif
Page 163 and 164:
DOE-STD-I090-96 (Rev-I)1. Class I-l
Page 165 and 166:
DOE-STD-I090-96 (Rev-I)CAUTIONONLY
Page 167 and 168:
-- ----------------------------10.4
Page 169 and 170:
DOE-STD-1090-96 (Rev-l)20. To avoid
Page 171 and 172:
DOE-STD-1090-96 (Rev-1)RAISE THE TI
Page 173 and 174:
-- -----------DOE-STD-I090-96 (Rev-
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
DOE-STD-1090-96 (Rev-l)Table 11-1.
Page 181 and 182:
DOE-STD-I090-96 (Rev-I)11.2 WIRE RO
Page 183 and 184:
-~ --~---------------------------DO
Page 185 and 186:
DOE-STD-I090-96 (Rev-I)11.3 SLINGS1
Page 187 and 188:
DOE-STD-1090-96 (Rev-1)11.3.1.3 Des
Page 189 and 190:
DOE-STD-I090-96 (Rev-I)Table 11-4.
Page 191 and 192:
Page 193 and 194:
DOE-STD-1090-96 (Rev-l)Table 11-8.
Page 195 and 196:
DOE-STD-I090-96 (Rev-I)Angle of cho
Page 197 and 198:
DOE-STD-I090-96 (Rev-I)temperatures
Page 199 and 200:
DOE-STD-I090-96 (Rev-!)7. Locate sl
Page 201 and 202:
-------------------DOE-STD-I090-96
Page 203 and 204:
-_.._-----~------------DOE-STD-I090
Page 205 and 206:
Page 207 and 208:
DOE·STD·I090·96 (Rev-I)q. Never
Page 209 and 210:
DOE-STD-I090-96 (Rev-I)j. Despite t
Page 211 and 212:
Page 213 and 214:
DOE·STD·1090-96 (Rev-1)certificat
Page 215 and 216:
DOE-STD-I090-96 (Rev-I)Exhibits I t
Page 217 and 218:
DOE-STD-1090-96 (Rev-l)lNTENTIONALL
Page 219 and 220: ------DOE-STD-I090-96 (Rev-I)EXHIBI
Page 221 and 222: DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 223 and 224: DOE-STD-1090-96 (Rev-l)INTENTIONALL
Page 225 and 226: -----------------------------------
Page 227 and 228: DOE-STD-I090-96 (Rev-I)Good and Bad
Page 229 and 230: 12.2 RIGGING HOOKSDOE-STD-I090-96 (
Page 231 and 232: DOE-STD-I090-96 (Rev-I)2. Heavy ser
Page 233 and 234: DOE-STD-I090-96 (Rev-I)Typical shac
Page 235 and 236: DOE-STD-I090-96 (Rev-I)• Shoulder
Page 237 and 238: 12.5 TURNBUCKLESDOE-STD-I090-96 (Re
Page 239 and 240: 12.6 LINKS AND RINGSDOE-STD-I090-96
Page 241 and 242: DOE-STD-I090-96 (Rev-I)12.7 METAL-P
Page 243 and 244: DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 245 and 246: ---------------------------DOE-STD-
Page 247 and 248: DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 249 and 250: DOE-STD-1090-96 (Rev-l)13.2 INSPECT
Page 251 and 252: DOE-STD-I090-96 (Rev-I)13.3 TESTING
Page 253 and 254: DOE-STD-1090-96 (Rev-l)13.4 NONDEST
Page 255 and 256: -------------------------------~--1
Page 257 and 258: -----------------------------------
Page 259 and 260: DOE-STD-1090-96 (Rev-1)14.4.4.3 Per
Page 261 and 262: DOE-STD-I090-96 (Rev-I)14.2 STRUCTU
Page 263 and 264: .----------------------------------
Page 265 and 266: DOE-STD-I090-96 (Rev-I)14.2.7 Maint
Page 267 and 268: DOE-STD-I090-96 (Rev-!)Four-pad pow
Page 269: DOE-STD-I090-96 (Rev-I)14.3.5 Testi
Page 273 and 274: DOE-STD-I090-96 (Rev-I)1. External
Page 275 and 276: DOE-STD-I090-96 (Rev-I)instructed b
Page 277 and 278: - ---------------------------------
Page 279 and 280: DOE-STD-I090-96 (Rev-I)6. Charging
Page 281 and 282: DOE-STD-!090-96 (Rev-!)EXHIBIT IPag
Page 283 and 284: -------------------~---------------
Page 285 and 286: DOE·STD·I090-96 (Rev-I)15.2 DEFIN
Page 287 and 288: General note for Figures 15-5 throu
Page 289 and 290: DOE-STD-I090-96 (Rev-I)LIFT, ORDINA
Page 291 and 292: DOE-STD-1090~96 (Rev-l)Consideratio
Page 293 and 294: DOE-STD-I090-96 (Rev-I)15.4.2.4 Fre
Page 295 and 296: DOE-STD-I090-96 (Rev-I)4. Corroded
Page 297 and 298: DOE-STD-I090-96 (Rev-I)attention to
Page 299 and 300: DOE-STD-I090-96 (Rev-I)b. Test load
Page 301 and 302: DOE-STD-!090-96 (Rev-!)regardless Q
Page 303 and 304: DOE-STD-1090-96 (Rev-1)EMERGENCY ST
Page 305 and 306: DOE-STD-I090-96 (Rev-I)so by an app
Page 307 and 308: DOE-STD-I090-96 (Rev-I)Figure 15-13
Page 313 and 314: DOE-STD-I090-96 (Rev-I)include the
Page 315 and 316: DOE-STD-1090-96 (Rev-l)the platform
Page 317 and 318: DOE-STD-I090-96 (Rev-I)h. Report an
Page 319 and 320: DOE-STD-!090-96 (Rev-!)fRAISE THE T
Page 321 and 322:
DOE-STD-I090-96 (Rev-I)h. Provide 4
Page 323 and 324:
DOE-STD-1090-96 (Rev-l)ASME B56.7,
Page 325 and 326:
show all

DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

Create successful ePaper yourself

Delete template?

Save as template?