DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

More documents

Recommendations

Info

DOE-STD-I090-96 (Rev-I)PROlt8IIED ZONIiSEE TABlE 9-3Figure 15-16. Danger zone for cranes and lifted loadsoperating near electical transmission line.15-29Chapter 15Construction Hoisting and RiggingEquipment Requirements
DOE-STD-I090-96 (Rev-I)include the following:1. Ensure that personnel involvedunderstand how the lift is to be made.2. Ensure that the weight ofthe load isdetermined. that proper equipment and accessoriesare selected. and that rated capacity is notexceeded.3. Survey the lift site forhazardous/unsafe conditions.4. Ensure that equipment is properly setup and positioned.5. Ensure that a signaler is assigned. ifrequired. and is identified to the operator.i. Identification and rated capacityofslings, lifting bars, riggingaccessories. and below-the-hooklifting devices.ii.iii.iv.Load-indicating devices.Load vectors.Lifting points.v. Sling angles.vi.vii.Boom and swing angles.Methods of attachment.viii. Crane orientations.6. Direct the lifting operation to ensurethat the lift is completed safely and efficiently.ix.Other factors affectingequipment capacity.7. Stop the job when any potentiallyunsafe condition is recognized.8. Direct operations if an accident orinjury occurs.e. The designated leader shall inspect all cranesto ensure that they are still within the inspectioninterval.f. The designated leader shall inspect all liftingdevices to ensure that the rated capacity oftheseitems ofequipment will not be exceeded.15.5.2.6 Critical Liftsa. The operating organization shall appoint aperson-in-charge (PIC) ofthe lifting operation.This person shall meet the definitions ofappointed. designated. and qualified. as describedin Section 15.2. "Definitions:'b. The PIC shall ensure that a pre-job plan isprepared that defmes the operation and shallinclude the following:1. Identification ofthe items to bemoved. the weight. dimensions. center ofgravity.and the presence ofhazardous or toxic materials.2. Identification ofcranes to be used bytype and rated capacity.3. Rigging sketches that include (asapplicable):4. Operating procedures and specialinstructions to operators including riggingprecautions and safety measures to be followed asapplicable.c. Only experienced operators who have beentrained and qualified to operate the specificequipment to be used shall be assigned to makethe lift.d. Only designated, qualified signalers shallgive signals to the operator. However. obey aSTOP signal at all times no matter who gives thesienal.e. The responsible manager or designee shallreview and approve the procedure and riggingsketches before the lift is made.15.5.2.7 Lifting Personnela. Do not lift, lower, swing, or travel the craneor forklift while a worker is on the hook. load,personnel platform. boom. or personnel-liftingdevice attached to the crane hoist rope. boom. ortines except as described in the paragraphs below.b. The person specifically responsible for theoverall work function to be performed shalldetermine that there is no practical alternativemachine or equipment to perform the work, suchas a ladder. scaffold. stairway. aerial lift, orpersonnel hoist. Ifa determination is made thatlifting by crane or forklift is required. theconstruction management contractor shall beChapter 15Construction Hoisting and RiggingEquipment Requirements 15-30
Page 1 and 2:
INCH-POUNDDOE STANDARDDOE-STD-1 090
Page 3:
DISCLAIMERPortions of this document
Page 7 and 8:
DOE-STD-I090-96 (Rev-I)7.5.6 Attach
Page 9 and 10:
DOE-STD-I090-96 (Rev-I)9.2.6.3 Hydr
Page 11 and 12:
DOE-STD-1090-96 (Rev-l)11.2.3.1 6 x
Page 13 and 14:
DOE-STD-1090-96 (Rev-l)13.4.5 Disco
Page 15 and 16:
DOE-STD-I090-96 (Rev-I)15.4.2 Mobil
Page 18 and 19:
DOE-STD-I090-96 (Rev-I)History and
Page 20 and 21:
DOE-STD-I090-96 (Rev-I)Acknowledgme
Page 22 and 23:
DOE-STD-I090-96 (Rev-I)Introduction
Page 24 and 25:
DOE-STD-I090-96 (Rev-I)CHAPTER 1TER
Page 26 and 27:
DOE-STD-I090-96 (Rev-I)CLOSING LINE
Page 28 and 29:
DOE-STD-I090-96 (Rev-I)END CONTROL:
Page 30 and 31:
LIFT, PREENGINEERED PRODUCTION:Repe
Page 32 and 33:
QUALIFIED ENGINEER/QUALIFIEDENGINEE
Page 35 and 36:
DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 37 and 38:
-----------------------------------
Page 39 and 40:
DOE-STD-I090-96 (Rev-I)2.2 CRITICAL
Page 41 and 42:
DOE-STD-1090-96 (Rev-1)INTENTIONALL
Page 43 and 44:
DOE-STD-I090-96 (Rev-I)3.2 OPERATIO
Page 45 and 46:
DOE-STD-I090-96 (Rev-I)2. Perform a
Page 47 and 48:
DOE-STD-I090-96 (Rev-I)3.4.4 Approv
Page 49 and 50:
DOE-STD-I090-96 (Rev-I)3.6 TRAINING
Page 51 and 52:
Page 53 and 54:
DOE-STD-I090-96 (Rev-I)that create
Page 55 and 56:
4.3 OVERHEAD CRANESDOE-STD-I090-96
Page 57 and 58:
DOE-STD-I090-96 (Rev-I)lNTENTIONAIL
Page 59 and 60:
Page 61 and 62:
DOE-STD-I090-96 (Rev-I)5.2 HOSTILE
Page 63 and 64:
DOE-STD-1090-96 (Rev-l)EXHIBIT IHOS
Page 65 and 66:
Page 67 and 68:
6.2 QUALIFICATIONDOE-STD-I090-96 (R
Page 69 and 70:
6.2.5Operators of ForkliftTrucksa.
Page 71 and 72:
DOE-STD-I090-96 (Rev-I)6.3 TRAINING
Page 73 and 74:
DOE-STD-1090-96 (Rev-l)24. Records
Page 75 and 76:
6.4 REQUALIFICATIONDOE-STD-I090-96
Page 77 and 78:
-----------------------------------
Page 79 and 80:
-----------------------------------
Page 81 and 82:
DOE-STD-I090-96 (Rev-!)Gantry Crane
Page 83 and 84:
DOE-STD-I090-96 (Rev-I)Crane bridge
Page 85 and 86:
DOE-STD-I090-96 (Rev-I)7.2 INSPECTI
Page 87 and 88:
DOE-STD-I090-96 (Rev-I)h. Chain-dri
Page 89 and 90:
DOE-STD-I090-96 (Rev-I)trouble pers
Page 91 and 92:
DOE-STD-I090-96 (Rev-I)7.4 MAINTENA
Page 93 and 94:
DOE-STD-I090-96 (Rev-I)HOIST. With
Page 95 and 96:
DOE-STD-I090-96 (Rev-I)g. Do not lo
Page 97 and 98:
DOE-STD-1090-96 (Rev-l). IN1ENTIONA
Page 99 and 100:
DOE-STD-1090-96 (Rev-l)EXHIBIT I (c
Page 101 and 102:
DOE-STD-I090-96 (Rev-I)EXHIBIT I (c
Page 103 and 104:
DOE-STD-I090-96 (Rev-I)8.3 TESTING
Page 105 and 106:
DOE-STD-I090-96 (Rev-I)Figure 8-3.
Page 107 and 108:
DOE-STD-I090-96 (Rev-I)8.1.1Operato
Page 109 and 110:
DOE-STD-I090-96 (Rev-I)operating co
Page 111 and 112:
Page 113 and 114:
DOE-STD-I090-96 (Rev-I)2. A number
Page 115 and 116:
DOE-STD-!090-96 (Rev-!)iv.Inspect f
Page 117 and 118:
Page 119 and 120:
DOE-STD-I090-96 (Rev-I)d. Do not op
Page 121 and 122:
DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 123 and 124:
Page 125 and 126:
DOE-STD-I090-96 (Rev-I)9.5.29.5.39.
Page 127 and 128:
DOE-STD-I090-96 (Rev-I)Table 9-1. S
Page 129 and 130:
DOE-STD-1090-96 (Rev-1)r-1r.ilE3...
Page 131 and 132:
Page 133 and 134:
DOE-STD-I090-96 (Rev-I)d. Evidence
Page 135 and 136:
DOE-STD-I090-96 (Rev-I)before retur
Page 137 and 138:
Page 139 and 140:
DOE-STD-I090-96 (Rev-!)t. Lock carr
Page 141 and 142:
DOE-STD-I090-96 (Rev-I)Figure 9-2.
Page 143 and 144:
DOE-STD-1090-96 (Rev-1)c. Durable s
Page 145 and 146:
DOE-STD-I090-96 (Rev-I)1. Cranel10a
Page 147 and 148:
DOE-STD-I090-96 (Rev-I)IIIIIIIIIIII
Page 149 and 150:
DOE·STD·I090·96 (Rev-I)HOIST. Wi
Page 151 and 152:
DOE-STD-I090-96 (Rev-I)RETRACT 800M
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
DOE-STD-1090-96 (Rev-1)10.5.5 Movin
Page 161 and 162:
DOE-STD-I090-96 (Rev-I)10.1.6 Modif
Page 163 and 164:
DOE-STD-I090-96 (Rev-I)1. Class I-l
Page 165 and 166:
DOE-STD-I090-96 (Rev-I)CAUTIONONLY
Page 167 and 168:
-- ----------------------------10.4
Page 169 and 170:
DOE-STD-1090-96 (Rev-l)20. To avoid
Page 171 and 172:
DOE-STD-1090-96 (Rev-1)RAISE THE TI
Page 173 and 174:
-- -----------DOE-STD-I090-96 (Rev-
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
DOE-STD-1090-96 (Rev-l)Table 11-1.
Page 181 and 182:
DOE-STD-I090-96 (Rev-I)11.2 WIRE RO
Page 183 and 184:
-~ --~---------------------------DO
Page 185 and 186:
DOE-STD-I090-96 (Rev-I)11.3 SLINGS1
Page 187 and 188:
DOE-STD-1090-96 (Rev-1)11.3.1.3 Des
Page 189 and 190:
DOE-STD-I090-96 (Rev-I)Table 11-4.
Page 191 and 192:
Page 193 and 194:
DOE-STD-1090-96 (Rev-l)Table 11-8.
Page 195 and 196:
DOE-STD-I090-96 (Rev-I)Angle of cho
Page 197 and 198:
DOE-STD-I090-96 (Rev-I)temperatures
Page 199 and 200:
DOE-STD-I090-96 (Rev-!)7. Locate sl
Page 201 and 202:
-------------------DOE-STD-I090-96
Page 203 and 204:
-_.._-----~------------DOE-STD-I090
Page 205 and 206:
Page 207 and 208:
DOE·STD·I090·96 (Rev-I)q. Never
Page 209 and 210:
DOE-STD-I090-96 (Rev-I)j. Despite t
Page 211 and 212:
Page 213 and 214:
DOE·STD·1090-96 (Rev-1)certificat
Page 215 and 216:
DOE-STD-I090-96 (Rev-I)Exhibits I t
Page 217 and 218:
DOE-STD-1090-96 (Rev-l)lNTENTIONALL
Page 219 and 220:
------DOE-STD-I090-96 (Rev-I)EXHIBI
Page 221 and 222:
Page 223 and 224:
DOE-STD-1090-96 (Rev-l)INTENTIONALL
Page 225 and 226:
-----------------------------------
Page 227 and 228:
DOE-STD-I090-96 (Rev-I)Good and Bad
Page 229 and 230:
12.2 RIGGING HOOKSDOE-STD-I090-96 (
Page 231 and 232:
DOE-STD-I090-96 (Rev-I)2. Heavy ser
Page 233 and 234:
DOE-STD-I090-96 (Rev-I)Typical shac
Page 235 and 236:
DOE-STD-I090-96 (Rev-I)• Shoulder
Page 237 and 238:
12.5 TURNBUCKLESDOE-STD-I090-96 (Re
Page 239 and 240:
12.6 LINKS AND RINGSDOE-STD-I090-96
Page 241 and 242:
DOE-STD-I090-96 (Rev-I)12.7 METAL-P
Page 243 and 244:
Page 245 and 246:
---------------------------DOE-STD-
Page 247 and 248:
Page 249 and 250:
DOE-STD-1090-96 (Rev-l)13.2 INSPECT
Page 251 and 252:
DOE-STD-I090-96 (Rev-I)13.3 TESTING
Page 253 and 254:
DOE-STD-1090-96 (Rev-l)13.4 NONDEST
Page 255 and 256:
-------------------------------~--1
Page 257 and 258:
-----------------------------------
Page 259 and 260:
DOE-STD-1090-96 (Rev-1)14.4.4.3 Per
Page 261 and 262: DOE-STD-I090-96 (Rev-I)14.2 STRUCTU
Page 263 and 264: .----------------------------------
Page 265 and 266: DOE-STD-I090-96 (Rev-I)14.2.7 Maint
Page 267 and 268: DOE-STD-I090-96 (Rev-!)Four-pad pow
Page 269 and 270: DOE-STD-I090-96 (Rev-I)14.3.5 Testi
Page 271 and 272: DOE-STD-I090-96 (Rev-I)14.4 MAGNETS
Page 273 and 274: DOE-STD-I090-96 (Rev-I)1. External
Page 275 and 276: DOE-STD-I090-96 (Rev-I)instructed b
Page 277 and 278: - ---------------------------------
Page 279 and 280: DOE-STD-I090-96 (Rev-I)6. Charging
Page 281 and 282: DOE-STD-!090-96 (Rev-!)EXHIBIT IPag
Page 283 and 284: -------------------~---------------
Page 285 and 286: DOE·STD·I090-96 (Rev-I)15.2 DEFIN
Page 287 and 288: General note for Figures 15-5 throu
Page 289 and 290: DOE-STD-I090-96 (Rev-I)LIFT, ORDINA
Page 291 and 292: DOE-STD-1090~96 (Rev-l)Consideratio
Page 293 and 294: DOE-STD-I090-96 (Rev-I)15.4.2.4 Fre
Page 295 and 296: DOE-STD-I090-96 (Rev-I)4. Corroded
Page 297 and 298: DOE-STD-I090-96 (Rev-I)attention to
Page 299 and 300: DOE-STD-I090-96 (Rev-I)b. Test load
Page 301 and 302: DOE-STD-!090-96 (Rev-!)regardless Q
Page 303 and 304: DOE-STD-1090-96 (Rev-1)EMERGENCY ST
Page 305 and 306: DOE-STD-I090-96 (Rev-I)so by an app
Page 307 and 308: DOE-STD-I090-96 (Rev-I)Figure 15-13
Page 309 and 310: DOE-STD-I090-96 (Rev-I)Figure 15-14
Page 311: DOE-STD-I090-96 (Rev-I)Figure 15-15
Page 315 and 316: DOE-STD-1090-96 (Rev-l)the platform
Page 317 and 318: DOE-STD-I090-96 (Rev-I)h. Report an
Page 319 and 320: DOE-STD-!090-96 (Rev-!)fRAISE THE T
Page 321 and 322: DOE-STD-I090-96 (Rev-I)h. Provide 4
Page 323 and 324: DOE-STD-1090-96 (Rev-l)ASME B56.7,
Page 325 and 326: DOE-STD-I090-96 (Rev-I)INTENTIONALL
show all

DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?