DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

More documents

Recommendations

Info

DOE-STD-1090-96 (Rev-l)7.5 OPERATIONa. The following shall apply to all personnelinvolved in overhead and gantry crane operation.b. At the initial stage ofthe planning process,an appointed person shall classify each lift intoone ofthe DOE-specified lift categories (ordinary,critical, orpreengineered production).7.5.1Conduct of Operator.a. Do not engage in any practice that willdivert your attention while operating the crane.b. Do not operate cranes without complyingwith the requirements of Chapter 6. Yourimmediate supervisor shall participate in thisdetermination.c. Operators shall be held directly responsiblefor the safe operation oftheir equipment.Whenever there is any question as to the safety ofthe activity, an operatorhas the authority to stopand refuse to handle loads until the matter hasbeen resolved by supervisory personnel.d. Sound a warning signal (iffurnished) duringtravel, particularly when approaching personnel.e. Ifyou fmd the crane's main or emergencyswitch open when starting on duty, do not close ituntil it has been determined that no one is on orclose to the crane. Ifthere is a warning sign on theswitch, do not remove it unless you placed it there.Do not close the switch until the warning sign hasbeen removed by the person who placed it there.f. Before closing the main switch, ensure thatall controllers are in the OFF position.g. Ifa power failure occurs during operation,immediately switch all controllers to the OFFposition.h. , Become familiar with your equipment andits proper care. Ifadjustments or repairs arenecessary, or any defects are mown, report thempromptly to the responsible supervisor. Also,notify the next operator ofthe defects at shiftchange.i. Contacts with runway stops or other cranesshall be made with extreme caution. Ifyou areordered to engage with or push other cranes, dothis with particular care for the safety ofpersonson or below the cranes, and only after makingcertain that any persons on the other cranes areaware ofwhat action is to be taken.j. Secure outdoor cranes before leaving them.Ie. When the wind-indicating alarm is given,anchor the bridge on outside cranes.1. Lock and tag the main positive electricalcontrol switch in the OPEN position before anycrane maintenance is performed.m. Operate all controls before beginning a newshift. Ifany controls do not operate properly,adjust or repair them before operations begin.n. Do not hoist two or more separately riggedloads in one lift, even though the combined loadiswithin the crane's rated capacity.o. Ensure that a 10BC or larger fIreextinguisher is installed in the cab ofcab-operatedcranes. The extinguisher shall be maintained in aserviceable condition.p. Do not lift, lower, or travel the crane whileanyone is on the load or hook.7.5.2 Hoist-LimitSwitch/Devicea. At the beginning ofeach work shift, or thefIrst time the crane is used during a shift, test theupper-limit switch/device ofeach hoist under noload. Exercise extreme care to avoidtwo-blocking; "inch" the block into the limitswitch or run it in at slow speed. Iftheswitch/device does not operate properly,immediately notify the supervisor.b. Ifa lift is in progress during a shift change,this testing requirement is considered to have beensatisfied for the completion ofthat lift. However,test the limit switch again before the next lift.c. Do not use the fmal hoist-limit switch!device that controls the upper limit of travel oftheload block as an operating control.7.5.3 Standard Hand SignalsThe standard hand signals for DOE use shall be asspecified in the latest edition ofthe ASME B30standards for the particular type of crane or hoistbeing used (see Figure 7-4).7·13Chapter 7Overhead and Gantry Cranes
DOE-STD-I090-96 (Rev-I)HOIST. With forearm vertical,forefinger pointing up, move hand insmall horizontal circles.LOWER. Extend arm downward,. forefinger pointing down, and movehand in small horizontal circles.BRIDGE. Arm extended forward,hand open and slightly raised, makepushing motion in direction of travel.TROLLEY TRAVEL. Palm up, fingerclosed, thumb pointing in direction ofmotion, jerk hand horizontally.EMERGENCY STOP. Extend arm,palm down, moving hand rapidly rightand left.MULTIPLE TROLLEYS. Hold up onefinger for block marked "1" and twofingers for block marked "2." Regularsi nals follow.,\MOVE SLOWLY. Use one hand togive any motion signal and place otherhand motionless above hand givingthe motion signal. (Hoist slowly shownasexam Ie.Figure 7-4. Standard hand signals for controlling overhead crane operation.Chapter 7Overhead and Gantry Cranes 7-14
Page 1 and 2:
INCH-POUNDDOE STANDARDDOE-STD-1 090
Page 3:
DISCLAIMERPortions of this document
Page 7 and 8:
DOE-STD-I090-96 (Rev-I)7.5.6 Attach
Page 9 and 10:
DOE-STD-I090-96 (Rev-I)9.2.6.3 Hydr
Page 11 and 12:
DOE-STD-1090-96 (Rev-l)11.2.3.1 6 x
Page 13 and 14:
DOE-STD-1090-96 (Rev-l)13.4.5 Disco
Page 15 and 16:
DOE-STD-I090-96 (Rev-I)15.4.2 Mobil
Page 18 and 19:
DOE-STD-I090-96 (Rev-I)History and
Page 20 and 21:
DOE-STD-I090-96 (Rev-I)Acknowledgme
Page 22 and 23:
DOE-STD-I090-96 (Rev-I)Introduction
Page 24 and 25:
DOE-STD-I090-96 (Rev-I)CHAPTER 1TER
Page 26 and 27:
DOE-STD-I090-96 (Rev-I)CLOSING LINE
Page 28 and 29:
DOE-STD-I090-96 (Rev-I)END CONTROL:
Page 30 and 31:
LIFT, PREENGINEERED PRODUCTION:Repe
Page 32 and 33:
QUALIFIED ENGINEER/QUALIFIEDENGINEE
Page 35 and 36:
DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 37 and 38:
-----------------------------------
Page 39 and 40:
DOE-STD-I090-96 (Rev-I)2.2 CRITICAL
Page 41 and 42: DOE-STD-1090-96 (Rev-1)INTENTIONALL
Page 43 and 44: DOE-STD-I090-96 (Rev-I)3.2 OPERATIO
Page 45 and 46: DOE-STD-I090-96 (Rev-I)2. Perform a
Page 47 and 48: DOE-STD-I090-96 (Rev-I)3.4.4 Approv
Page 49 and 50: DOE-STD-I090-96 (Rev-I)3.6 TRAINING
Page 51 and 52: DOE-STD-I090-96 (Rev-I)INTENTIONALL
Page 53 and 54: DOE-STD-I090-96 (Rev-I)that create
Page 55 and 56: 4.3 OVERHEAD CRANESDOE-STD-I090-96
Page 57 and 58: DOE-STD-I090-96 (Rev-I)lNTENTIONAIL
Page 61 and 62: DOE-STD-I090-96 (Rev-I)5.2 HOSTILE
Page 63 and 64: DOE-STD-1090-96 (Rev-l)EXHIBIT IHOS
Page 67 and 68: 6.2 QUALIFICATIONDOE-STD-I090-96 (R
Page 69 and 70: 6.2.5Operators of ForkliftTrucksa.
Page 71 and 72: DOE-STD-I090-96 (Rev-I)6.3 TRAINING
Page 73 and 74: DOE-STD-1090-96 (Rev-l)24. Records
Page 75 and 76: 6.4 REQUALIFICATIONDOE-STD-I090-96
Page 77 and 78: -----------------------------------
Page 79 and 80: -----------------------------------
Page 81 and 82: DOE-STD-I090-96 (Rev-!)Gantry Crane
Page 83 and 84: DOE-STD-I090-96 (Rev-I)Crane bridge
Page 85 and 86: DOE-STD-I090-96 (Rev-I)7.2 INSPECTI
Page 87 and 88: DOE-STD-I090-96 (Rev-I)h. Chain-dri
Page 89 and 90: DOE-STD-I090-96 (Rev-I)trouble pers
Page 91: DOE-STD-I090-96 (Rev-I)7.4 MAINTENA
Page 95 and 96: DOE-STD-I090-96 (Rev-I)g. Do not lo
Page 97 and 98: DOE-STD-1090-96 (Rev-l). IN1ENTIONA
Page 99 and 100: DOE-STD-1090-96 (Rev-l)EXHIBIT I (c
Page 101 and 102: DOE-STD-I090-96 (Rev-I)EXHIBIT I (c
Page 103 and 104: DOE-STD-I090-96 (Rev-I)8.3 TESTING
Page 105 and 106: DOE-STD-I090-96 (Rev-I)Figure 8-3.
Page 107 and 108: DOE-STD-I090-96 (Rev-I)8.1.1Operato
Page 109 and 110: DOE-STD-I090-96 (Rev-I)operating co
Page 113 and 114: DOE-STD-I090-96 (Rev-I)2. A number
Page 115 and 116: DOE-STD-!090-96 (Rev-!)iv.Inspect f
Page 117 and 118: DOE-STD-I090-96 (Rev-I)8.4 MAINTENA
Page 119 and 120: DOE-STD-I090-96 (Rev-I)d. Do not op
Page 121 and 122: DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 123 and 124: DOE-STD-I090-96 (Rev-I)EXHIBIT I (c
Page 125 and 126: DOE-STD-I090-96 (Rev-I)9.5.29.5.39.
Page 127 and 128: DOE-STD-I090-96 (Rev-I)Table 9-1. S
Page 129 and 130: DOE-STD-1090-96 (Rev-1)r-1r.ilE3...
Page 133 and 134: DOE-STD-I090-96 (Rev-I)d. Evidence
Page 135 and 136: DOE-STD-I090-96 (Rev-I)before retur
Page 137 and 138: DOE-STD-I090-96 (Rev-I)9.4 MAINTENA
Page 139 and 140: DOE-STD-I090-96 (Rev-!)t. Lock carr
Page 141 and 142: DOE-STD-I090-96 (Rev-I)Figure 9-2.
Page 143 and 144:
DOE-STD-1090-96 (Rev-1)c. Durable s
Page 145 and 146:
DOE-STD-I090-96 (Rev-I)1. Cranel10a
Page 147 and 148:
DOE-STD-I090-96 (Rev-I)IIIIIIIIIIII
Page 149 and 150:
DOE·STD·I090·96 (Rev-I)HOIST. Wi
Page 151 and 152:
DOE-STD-I090-96 (Rev-I)RETRACT 800M
Page 153 and 154:
DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 155 and 156:
DOE-STD-I090-96 (Rev-I)EXHIBIT I (c
Page 157 and 158:
Page 159 and 160:
DOE-STD-1090-96 (Rev-1)10.5.5 Movin
Page 161 and 162:
DOE-STD-I090-96 (Rev-I)10.1.6 Modif
Page 163 and 164:
DOE-STD-I090-96 (Rev-I)1. Class I-l
Page 165 and 166:
DOE-STD-I090-96 (Rev-I)CAUTIONONLY
Page 167 and 168:
-- ----------------------------10.4
Page 169 and 170:
DOE-STD-1090-96 (Rev-l)20. To avoid
Page 171 and 172:
DOE-STD-1090-96 (Rev-1)RAISE THE TI
Page 173 and 174:
-- -----------DOE-STD-I090-96 (Rev-
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
DOE-STD-1090-96 (Rev-l)Table 11-1.
Page 181 and 182:
DOE-STD-I090-96 (Rev-I)11.2 WIRE RO
Page 183 and 184:
-~ --~---------------------------DO
Page 185 and 186:
DOE-STD-I090-96 (Rev-I)11.3 SLINGS1
Page 187 and 188:
DOE-STD-1090-96 (Rev-1)11.3.1.3 Des
Page 189 and 190:
DOE-STD-I090-96 (Rev-I)Table 11-4.
Page 191 and 192:
Page 193 and 194:
DOE-STD-1090-96 (Rev-l)Table 11-8.
Page 195 and 196:
DOE-STD-I090-96 (Rev-I)Angle of cho
Page 197 and 198:
DOE-STD-I090-96 (Rev-I)temperatures
Page 199 and 200:
DOE-STD-I090-96 (Rev-!)7. Locate sl
Page 201 and 202:
-------------------DOE-STD-I090-96
Page 203 and 204:
-_.._-----~------------DOE-STD-I090
Page 205 and 206:
Page 207 and 208:
DOE·STD·I090·96 (Rev-I)q. Never
Page 209 and 210:
DOE-STD-I090-96 (Rev-I)j. Despite t
Page 211 and 212:
Page 213 and 214:
DOE·STD·1090-96 (Rev-1)certificat
Page 215 and 216:
DOE-STD-I090-96 (Rev-I)Exhibits I t
Page 217 and 218:
DOE-STD-1090-96 (Rev-l)lNTENTIONALL
Page 219 and 220:
------DOE-STD-I090-96 (Rev-I)EXHIBI
Page 221 and 222:
Page 223 and 224:
DOE-STD-1090-96 (Rev-l)INTENTIONALL
Page 225 and 226:
-----------------------------------
Page 227 and 228:
DOE-STD-I090-96 (Rev-I)Good and Bad
Page 229 and 230:
12.2 RIGGING HOOKSDOE-STD-I090-96 (
Page 231 and 232:
DOE-STD-I090-96 (Rev-I)2. Heavy ser
Page 233 and 234:
DOE-STD-I090-96 (Rev-I)Typical shac
Page 235 and 236:
DOE-STD-I090-96 (Rev-I)• Shoulder
Page 237 and 238:
12.5 TURNBUCKLESDOE-STD-I090-96 (Re
Page 239 and 240:
12.6 LINKS AND RINGSDOE-STD-I090-96
Page 241 and 242:
DOE-STD-I090-96 (Rev-I)12.7 METAL-P
Page 243 and 244:
DOE-STD-I090-96 (Rev-I)Exhibit I is
Page 245 and 246:
---------------------------DOE-STD-
Page 247 and 248:
Page 249 and 250:
DOE-STD-1090-96 (Rev-l)13.2 INSPECT
Page 251 and 252:
DOE-STD-I090-96 (Rev-I)13.3 TESTING
Page 253 and 254:
DOE-STD-1090-96 (Rev-l)13.4 NONDEST
Page 255 and 256:
-------------------------------~--1
Page 257 and 258:
-----------------------------------
Page 259 and 260:
DOE-STD-1090-96 (Rev-1)14.4.4.3 Per
Page 261 and 262:
DOE-STD-I090-96 (Rev-I)14.2 STRUCTU
Page 263 and 264:
.----------------------------------
Page 265 and 266:
DOE-STD-I090-96 (Rev-I)14.2.7 Maint
Page 267 and 268:
DOE-STD-I090-96 (Rev-!)Four-pad pow
Page 269 and 270:
DOE-STD-I090-96 (Rev-I)14.3.5 Testi
Page 271 and 272:
DOE-STD-I090-96 (Rev-I)14.4 MAGNETS
Page 273 and 274:
DOE-STD-I090-96 (Rev-I)1. External
Page 275 and 276:
DOE-STD-I090-96 (Rev-I)instructed b
Page 277 and 278:
- ---------------------------------
Page 279 and 280:
DOE-STD-I090-96 (Rev-I)6. Charging
Page 281 and 282:
DOE-STD-!090-96 (Rev-!)EXHIBIT IPag
Page 283 and 284:
-------------------~---------------
Page 285 and 286:
DOE·STD·I090-96 (Rev-I)15.2 DEFIN
Page 287 and 288:
General note for Figures 15-5 throu
Page 289 and 290:
DOE-STD-I090-96 (Rev-I)LIFT, ORDINA
Page 291 and 292:
DOE-STD-1090~96 (Rev-l)Consideratio
Page 293 and 294:
DOE-STD-I090-96 (Rev-I)15.4.2.4 Fre
Page 295 and 296:
DOE-STD-I090-96 (Rev-I)4. Corroded
Page 297 and 298:
DOE-STD-I090-96 (Rev-I)attention to
Page 299 and 300:
DOE-STD-I090-96 (Rev-I)b. Test load
Page 301 and 302:
DOE-STD-!090-96 (Rev-!)regardless Q
Page 303 and 304:
DOE-STD-1090-96 (Rev-1)EMERGENCY ST
Page 305 and 306:
DOE-STD-I090-96 (Rev-I)so by an app
Page 307 and 308:
DOE-STD-I090-96 (Rev-I)Figure 15-13
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
DOE-STD-I090-96 (Rev-I)include the
Page 315 and 316:
DOE-STD-1090-96 (Rev-l)the platform
Page 317 and 318:
DOE-STD-I090-96 (Rev-I)h. Report an
Page 319 and 320:
DOE-STD-!090-96 (Rev-!)fRAISE THE T
Page 321 and 322:
DOE-STD-I090-96 (Rev-I)h. Provide 4
Page 323 and 324:
DOE-STD-1090-96 (Rev-l)ASME B56.7,
Page 325 and 326:
show all

DOE-STD-1090-96, DOE Standard Hoisting and Rigging Manual ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?