PROJECT MANUAL Specifications Seafood Removal Walmart Store No 1186 Liberty TX

excessive exhaust gases containing carbon dioxide (CO2) or carbon monoxide (CO). During slab
placement and curing periods, maximum CO2 levels shall be 4,500 parts per million and maximum CO
levels shall be 15 parts per million at concrete surface within 5 feet of any source of exhaust gases to
minimize potential damage to concrete.
1.8 COORDINATION AND SCHEDULING
A. Pursuant to Article 15 –of the General Conditions, the Owner has the right to perform construction work and to
award separate contracts on the Project site.
B. The construction work and separate contracts on the Project site associated with the floor slab construction may
includeLP cabling, CCTV cabling, Test and Balance, Telecom, Data cabling, and Alarms.
C. Owner Or Separate Contractor Responsibilities: The following provisions are provided as information with
respect to the responsibilities of the Owner or Separate Contractors doing work on, or related to, the building floor
slab construction. The Owner or separate contractors must:
1. Notify General Contractor’s superintendent 1 week prior to the start of the work at the job site. Make sure
superintendent has names and contact phone numbers.
2. Assure workmen who will be working on or around the floor slab, view the Owner’s Contractors Training
and Instructional Video and Pre-Slab Conference Video prior to the start of work or installation.
3. Coordinate work and schedule activities with floor slab construction to avoid interference and to minimize
detrimental effects to floor finish. Allowable time to work on the slab is a minimum of 11 days after
placement, provided the contractor follows the installation procedure required. (Day 1 Pour slab, 7 days wet
cure, 2 days clean and dry, 1 day first application of densifier, 2 days dry = 11 days)
4. Not walk through or on areas where floor construction or finishing operations are being preformed.
5. Perform precautionary measures to protect floor finish. Inspect machinery used on floor slab daily, at a
minimum, for embedded items in tires; remove items which may damage or scratch floor. Diaper all lifts
and other equipment used on the floor slab. White tires are required on lifts. Take measures to prevent tools
or other items that may cause impact damage, discoloration, or other surface blemishes. Owner or Separate
Contractors are required to provide protection to slab in what ever measures are needed i.e. providing
plywood, carpet, house wrap etc for impact protection. (Plastic sheets are not approved for protection)
Remove or consolidate protection on a regular basis to prevent discoloring.
6. Damage to concrete floor finish determined by Wal-Mart to be the responsibility of the Owner or Separate
Contractor will be repaired in accordance with approved methods, materials, and personnel at the expense
of the Owner or Separate Contractor.
PART 2 - PRODUCTS
2.1 MATERIALS
A. Subject to compliance with project requirements, provide products as manufactured by the following to the extent
as specified hereinafter for the specific product:
1. Ardex Engineered Cements, (412) 264-4240.
2. BASF Admixtures Inc., Cleveland, OH (Formerly Master Builders) (800) 628-9990.
3. BASF Building Systems, Shakopee, MN (Formerly Degussa Building Products) (800) 433-9517.
4. Colloid Environmental Technologies Co. (CETCO), (800) 527-9948
5. Conspec (Dayton Superior) (913) 287-1700 or (877) 416-3439.
6. Davis Colors, (800) 800-6856.
7. Dayton Superior Chemical, (866) 329-8724.
8. Degussa Building Products: See BASF Building Systems.
9. DRC Inc., Carrollton, KY (502) 732-1001.
10. E-Poxy Industries, Inc., (800) 833-3400.
11. Euclid Chemical Co., (877) 438-3826.
12. EZform, Inc., (866) 913-8363.
03312-8
Walmart #1186 – Liberty, TX 04/20/11
CMA/10118.034