PROJECT MANUAL Specifications Seafood Removal Walmart Store No 1186 Liberty TX

More documents

Recommendations

Info

2. In joints where plumbing fixtures meet adjacent floor and wall finishes, match color of plumbing fixture. 3. Use clear, colorless sealant where applied to stainless steel surfaces. 2.2 EXPANDING FOAM SEALANTS A. Polyurethane Expanding Foam Sealants: 1. Polyurethane Expanding Foam Sealant #1 (EF1): Closed-cell foam and non-flammable propellant; urea formaldehyde-free, CFC-free; UL Class 1 Foam with flame spread of 20 and smoke developed of 25 as tested in accordance with ASTM E84. a. Touch'n Seal Quick Cure, by Convenience Products. b. Space Invader by GE Sealants & Adhesives, (877) 943-7325. 2.3 JOINT FILLER (BUILDING) A. Preformed Control Joint Filler: 1. Regular Joint: 2-5/8 inches by 1-1/2 inches; rubber. a. Rapid Control Joint DA2001 by Dur-O-Wal (Dayton Superior), Dayton, OH (888) 977-9600. b. Masonry Control Joint No. 571 by Greenstreak, St. Louis, MO (800) 325-9504. 2. Tee Joint: 2-5/8 inches by 1 inch; rubber. a. Rapid Control Joint D/A 2025 by Dur-O-Wal. b. Masonry Control Joint No. 572 by Greenstreak. B. Expansion Joint Filler (Compression Seal): 1. Backerseal (Grayflex) expanding precompressed foam by Emseal Joint Systems, Ltd., Westborough, MA (800) 526-8365. 2. Willseal 600 polyurethyene foam joint sealing tape by Willseal USA, Pelham, NH (800) 438-0684. 2.4 JOINT-SEALANT BACKING (BUILDING) A. Sealant Backing (Backer Rod): Provide sealant backings of material and type that are nonstaining; are compatible with joint substrates, sealants, primers, and other joint fillers; and are approved for applications indicated by sealant manufacturer based on field experience and laboratory testing. 1. Cylindrical Sealant Backings: ASTM C 1330, types as approved by joint-sealant manufacturer for joint application indicated, and of size and density to control sealant depth and otherwise contribute to producing optimum sealant performance: 2. Elastomeric Tubing Sealant Backings: Neoprene, butyl, EPDM, or silicone tubing complying with ASTM D 1056, B. Bond-Breaker Tape: Polyethylene tape or other plastic tape recommended by sealant manufacturer for preventing sealant from adhering to rigid, inflexible joint-filler materials or joint surfaces at back of joint where such adhesion would result in sealant failure. Provide self-adhesive tape where applicable. 2.5 INTERIOR SLAB ON GRADE JOINT SEALANT MATERIALS A. Preformed Expansion (Isolation) Joint Filler (PMEJ) Strips: Flexible closed-cell synthetic foam expansion joint strips, non-extruding, for full depth of concrete. 1. Ceramar Flexibe Foam Expansion Joint, by W.R. Meadows. 2. Deck-O-Foam Expansion Joint Filler, by W.R. Meadows 3. Expansion Joint Filler, by BASF Building Systems (Degussa) (Formerly Sonneborn Sonolastic). B. Elastomeric Joint Materials: 1. Sealant: a. Polyurethane Sealant: No. 2 (P2) as specified above. b. Color: Match color of adjacent exposed surface of concrete slab.. c. Sealant shall be compatible with construction material placed against it. 07900-3 Walmart #1186 – Liberty, TX 04/20/11 CMA/10118.034
2. Joint Back-Up Material: a. Polyethylene Foam, 100% closed cell. b. Material shall be compatible with construction material to be placed against it such as tile adhesive. C. Polyurea Joint Filler (PY1): Rapid setting, two-component polyurea polymer liquid of 100% solids content, Shore Hardness 85 to 92, compatible with construction material placed against it. (USDA Certified, unless otherwise noted.) 1. Spall-Pro RS 88 (Non-USDA), by Metzger/McGuire. 2. Euco Qwik Joint 200 (Non-USDA), by Euclid Chemical. 3. VersaFlex SL/85, by VersaFlex. 4. Quick Joint 85, by CSS Polymers. 5. Match color of adjacent exposed surface of concrete. PART 3 - EXECUTION 3.1 EXAMINATION A. Verify that surfaces and joint openings are ready to receive work and field measurements are as indicated on Drawings. B. Beginning of installation means installer accepts existing substrates. 3.2 PREPARATION A. Clean and prime joints in accordance with manufacturer's instructions. B. Remove loose materials and foreign matter which might impair adhesion of sealant. C. Verify that joint backing and release tapes are compatible with sealant. D. Protect elements surrounding work of this Section from damage or disfiguration. 3.3 INSTALLATION A. Install sealant in accordance with manufacturer's instructions. B. Measure joint dimensions and size materials to achieve required width/depth ratios. C. Install joint backing to achieve neck dimension no greater than 1/3 the joint width. D. Install bond breaker where joint backing is not used. E. Apply sealant within recommended temperature ranges. Consult manufacturer when sealant cannot be applied within recommended temperature ranges. F. Install sealant free of air pockets, foreign embedded matter, ridges, and sags. G. Tool joints concave. 3.4 INTERIOR SLAB ON GRADE JOINT SEALING AND FILLING A. General: 1. Seal/fill contraction, isolation and construction joints in floor slabs and pavements, unless otherwise indicated on Drawings or specified herein. 07900-4 Walmart #1186 – Liberty, TX 04/20/11 CMA/10118.034
Page 1 and 2:
1300 Summit Avenue Suite 300 Fort W
Page 3 and 4:
UniSpecDOCUMENT 00007 - SEALS PAGE
Page 5 and 6:
SEALS PAGE (Continued) STRUCTURAL E
Page 8 and 9:
UniSpec II - Store Planning 032610
Page 10 and 11:
16050 Basic Electrical Materials an
Page 12 and 13:
A. Limit use of site to allow for:
Page 14:
Page 17 and 18:
A. A $250 administrative cost will
Page 20 and 21:
UniSpec II- Store Planning 012910 S
Page 22 and 23:
Page 24 and 25:
1.4 SCHEDULE UPDATES A. The Contrac
Page 26 and 27:
1.3 TRANSMITTAL A. Transmit each su
Page 28 and 29:
UniSpec II- Store Planning 043010 R
Page 30 and 31:
UniSpec II-Store Planning 111910 SE
Page 32 and 33:
O. Periodic Inspection: The part-ti
Page 34 and 35:
samples. Provide lift equipment as
Page 36 and 37:
Concrete Slabs) 03931 - Existing In
Page 38 and 39:
Page 40 and 41:
NEUTRALIZATION ENCLOSURE CERTIFICAT
Page 42 and 43:
A. Provide, maintain and pay for te
Page 44 and 45:
3. Office space with desk and chair
Page 46 and 47:
1.21 SIGNAGE A. Temporary Construct
Page 48 and 49:
Page 50 and 51:
Not Used END OF SECTION 01600-3 Wal
Page 52 and 53:
D. Remove packaging and clean produ
Page 54 and 55:
Page 56 and 57:
9. The Contractor shall verify exis
Page 58 and 59:
G. Obtain all required inspections
Page 60 and 61:
2. Where a product or type of const
Page 62 and 63:
C. Cleaning materials shall be clea
Page 64 and 65:
12. Touch up and otherwise repair a
Page 66 and 67:
K. Re-Use: The use, in the same or
Page 68 and 69:
G. Supply workers and subcontractor
Page 70 and 71:
Page 72 and 73:
a. Elastomeric Membrane Roofing (Se
Page 74 and 75:
STORE/CLUB TYPE (Check Those That A
Page 76 and 77:
Rubber: VCT: PVC: Ceramic: R.R. Par
Page 78 and 79:
[CONTRACTOR’S LETTERHEAD] CONTRAC
Page 80 and 81:
7. Test soils around buried tanks f
Page 82 and 83:
3. Storage or sale of removed items
Page 84 and 85:
3.4 DISPOSAL OF DEMOLISHED MATERIAL
Page 86 and 87:
Page 88 and 89:
E. Contact Wal-Mart Store Planning
Page 90 and 91:
3.2 INSTALLATION A. Install shoring
Page 92 and 93:
B. Satisfactory Materials: ASTM D 2
Page 94 and 95:
A. Classification of Excavation: Th
Page 96 and 97:
C. Work shall be preformed by a Spe
Page 98 and 99:
2. ACI 301 - Structural Concrete. 3
Page 100 and 101:
e. Data indicating chloride ion con
Page 102 and 103:
1. The concrete floor finishing sub
Page 104 and 105:
excessive exhaust gases containing
Page 106 and 107:
2.3 FORMWORK: A. Forms: 1. Plywood,
Page 108 and 109:
A. Provide admixture products as sp
Page 110 and 111:
average times of initial setting. T
Page 112 and 113:
B. Design, construct, erect, suppor
Page 114 and 115:
4. Space joints to allow one contin
Page 116 and 117: supplementary cementing materials,
Page 118 and 119: 4. Spread compound evenly using mop
Page 120 and 121: sieve analysis of material retained
Page 122 and 123: 3. Prevention of stored materials i
Page 124 and 125: C. MIX DESIGN Cement Coarse Aggrega
Page 126 and 127: CONTRACTOR'S QUALIFICATION STATEMEN
Page 128 and 129: TABLE A TESTING AND INSPECTION SCHE
Page 130 and 131: 03312-34 Walmart #1186 - Liberty, T
Page 132 and 133: 2. Limit and control damage from no
Page 134 and 135: 2.4 EQUIPMENT A. Scrubber Machines
Page 136 and 137: 3.6 FINISH REQUIREMENTS: A. Gloss:
Page 138 and 139: UniSpec II - Store Planning 073109
Page 140 and 141: 1. Comply with current Federal and
Page 142 and 143: 2. American Decorative Concrete (80
Page 144 and 145: 1. Pentra-Guard (HP) by Convergent
Page 146 and 147: E. Continue burnishing operations u
Page 148 and 149: UniSpec II- Store Planning 073109 [
Page 150 and 151: 3. Notify Walmart Concrete Consulta
Page 152 and 153: A. Concrete lithium based chemical
Page 154 and 155: E. Continue burnishing operations u
Page 156 and 157: UniSpec II- Store Planning 022610 S
Page 158 and 159: E. Galvanized Steel Sheets: 1. Stru
Page 160 and 161: H. Interior Stainless Steel Bollard
Page 162 and 163: F. Finish: Embossed. G. Color: Prov
Page 168 and 169: 2. Unless noted otherwise, use poly
Page 170 and 171: INTERIOR JOINTS MATERIAL TO MATERIA
Page 174 and 175: 3.2 INSTALLATION (BY CONTRACTOR) A.
Page 176 and 177: C. Gypsum Association (GA): 1. GA-2
Page 178 and 179: N. Flat Straps and Plates: ASTM A 6
Page 180 and 181: . Substitutions not permitted. 2. E
Page 182 and 183: together. b. Install optional produ
Page 184 and 185: 3.9 INSTALLATION - GYPSUM BOARD A.
Page 186 and 187: items installed within framing. 3.1
Page 188 and 189: PART 2 - PRODUCTS 2.1 MANUFACTURERS
Page 190 and 191: E. Locate system on room axis accor
Page 192 and 193: f. Kencove vinyl: No. KC213 Granite
Page 196 and 197: 2.2 MATERIALS A. Paint: Wal-Mart an
Page 198 and 199: 3.4 MECHANICAL AND ELECTRICAL EQUIP
Page 200 and 201: 3.9 PAINT SHEEN SCHEDULE A. Gloss:
Page 202 and 203: tion) Concrete Masonry Unit (Previo
Page 204 and 205: A. Plastic: 1. Clear Plastic: a. Sp
Page 208 and 209: 2. If the Contractor subcontracts t
Page 210 and 211: PART 2 - PRODUCTS 2.1 ENERGY MANAGE
Page 212 and 213: I. Cable: 1. Provide communication
Page 214 and 215: 13810-9 Walmart #1186 - Liberty, TX
Page 216 and 217:
WAL-MART SUPPORT INSTALLATION FORM
Page 218 and 219:
PRE-CHECKOUT VERIFICATION FORM HOA
Page 220 and 221:
HVAC INFORMATION Rtu # Cool Stage H
Page 222 and 223:
CUTLER HAMMER MODULE CONFIGURATIONS
Page 224 and 225:
PULSE METER LETTER Cutler-Hammer IQ
Page 226 and 227:
OPERATING INFORMATION Communication
Page 228 and 229:
Page 230 and 231:
3.3 SCHEDULES: Schedules below appl
Page 232 and 233:
Page 234 and 235:
3) Coupling Housings: Ductile iron
Page 236 and 237:
2.5 DRAINS, CLEANOUTS, HOSE BIBBS,
Page 238 and 239:
E. Install Y-pattern strainers for
Page 240 and 241:
B. Contractor Qualifications: Testi
Page 242 and 243:
G. Report: 1. Provide summary repor
Page 244 and 245:
Page 246 and 247:
B. Make an inspection of installed
Page 248 and 249:
D. As equipment is received, Refrig
Page 250 and 251:
C. Make joints with use of brazing
Page 252 and 253:
B. Do not endanger any work by cutt
Page 254 and 255:
15600-11 Walmart #1186 - Liberty, T
Page 256 and 257:
Page 258 and 259:
15700-3 Walmart #1186 - Liberty, TX
Page 260 and 261:
Page 262 and 263:
D. Duct Wrap: ASTM C553. 1. Materia
Page 264 and 265:
B. Substitutions: Not permitted. 2.
Page 266 and 267:
3.8 SCHEDULES SCHEDULE I - DUCT SUP
Page 268 and 269:
Page 270 and 271:
3.3 TESTING A. Upon completion of i
Page 272 and 273:
Page 274 and 275:
2.3 OUTLET BOXES AND CONDUIT FITTIN
Page 276 and 277:
9. GFCI Duplex Receptacle 20A 125V
Page 278 and 279:
7. Single Locking Receptacle 30A 12
Page 280 and 281:
2. Plug 20A 250V 2 Pole 3 Wire Grou
Page 282 and 283:
I. Pin & Sleeve - Insulated Water T
Page 284 and 285:
3. If tank and tank indicators are
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
show all

PROJECT MANUAL Specifications Seafood Removal Walmart Store No 1186 Liberty TX

Create successful ePaper yourself

Delete template?

Save as template?