Datascope - Mindray

More documents

Recommendations

Info

Periodic Maintenance Functional Tests 3. Select Continue to prompt to the Normal Screen. FIGURE 6-21 Compliance Test Results 6.8.4.5 Manual Leak Test NOTE: The Manual Leak Test detects smaller leaks than can be detected in the Automatic Leak Test. 1. Ensure that the gas pressure for O 2 , N 2 O, and AIR are at 50 ±10 psi. 2. Power ON the AS3000. 3. Attach a reusable-silicone-rubber breathing circuit to the Breathing System. NOTE: For testing purposes always use a reusable breathing circuit. 4. Tightly connect the Y-fitting on the breathing circuit to the test port. 5. Attach a breathing bag to the bag arm. 6. Set the APL Valve to the fully closed position (70 cmH 2O). 7. Rotate the O 2 Flow Control Valve until 50 cmH 2 O pressure is observed on the Airway Pressure Gauge. 8. Verify that the flow required to stabilize the pressure is less than 300 mL/min. AS3000 Service Manual 0070-10-0683 6 - 21
Functional Tests Periodic Maintenance 6.8.4.6 Oxygen Sensor Calibration NOTE: Oxygen Sensor Calibration can be performed in all ventilation modes. 1. Press the MENU key and then use the Navigator Knob to scroll to the Calibrate menu tab (see FIGURE 6-22). Select the Start Calibration button. FIGURE 6-22 Calibrate Menu Tab 2. After the Start Calibration button has been selected, the screen shown in FIGURE 6-23 will be displayed, instructing the user to remove the oxygen sensor from the Breathing System and expose it to room air for at least 3 minutes before proceeding. After at least 3 minutes have passed, select the Next button to initiate the calibration process. The progress bar shown in FIGURE 6-24 will be displayed. NOTE: If the system is going to be used during the calibration, insert the O 2 cell plug into the port from which the oxygen sensor was removed using a push and turn motion. 6 - 22 0070-10-0683 AS3000 Service Manual
Page 1 and 2:
Datascope AS AnesthesiA Delivery sy
Page 3 and 4:
AS3000 is a U.S. trademark of Mind
Page 5 and 6:
Table of Contents Manual Breathing
Page 7 and 8:
Table of Contents System Self Test.
Page 9 and 10:
Table of Contents This page intenti
Page 11 and 12:
Introduction Cautions WARNING: Comp
Page 13 and 14:
Introduction Notes This page intent
Page 15 and 16:
Microprocessor-controlled Ventilato
Page 17 and 18:
Components Theory of Operation 3. U
Page 19 and 20:
Components Theory of Operation 14.
Page 21 and 22:
Components Theory of Operation 26.
Page 23 and 24:
Components Theory of Operation 1.3.
Page 25 and 26:
Ventilator Control and Drive Theory
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Anesthesia System Components Theory
Page 45 and 46:
Ventilator UI Theory of Operation F
Page 47 and 48:
Ventilator UI Theory of Operation 1
Page 49 and 50:
Ventilator Pneumatic - O 2 Drive Ga
Page 51 and 52:
The Breathing System Theory of Oper
Page 53 and 54:
The Breathing System Theory of Oper
Page 55 and 56:
Assembly Installation Guide 2.2 Ass
Page 57 and 58:
Assembly Installation Guide 2. Atta
Page 59 and 60:
Assembly Installation Guide 2.2.11
Page 61 and 62:
Installation Checkout Procedure Ins
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Warnings and Cautions Repair Inform
Page 83 and 84:
3 - 4 0070-10-0683 AS3000 Service M
Page 85 and 86:
3 - 6 0070-10-0683 AS3000 Service M
Page 87 and 88:
3 - 8 0070-10-0683 AS3000 Service M
Page 89 and 90:
3 - 10 0070-10-0683 AS3000 Service
Page 91 and 92:
3 - 12 0070-10-0683 AS3000 Service
Page 93 and 94:
3 - 14 0070-10-0683 AS3000 Service
Page 95 and 96:
3 - 16 0070-10-0683 AS3000 Service
Page 97 and 98: 3 - 18 0070-10-0683 AS3000 Service
Page 99 and 100: Available Replacement Parts and Sub
Page 101 and 102: Isometric Drawings Replacement Part
Page 115 and 116: Calibration Warnings, Precautions,
Page 117 and 118: General Guidelines Calibration 5.3
Page 119 and 120: Calibration Procedures Calibration
Page 129 and 130: Periodic Maintenance Schedule of Se
Page 131 and 132: Check Valve Cleaning Periodic Maint
Page 141 and 142: Functional Tests Periodic Maintenan
Page 147: Functional Tests Periodic Maintenan
Page 167 and 168: Preoperative Checklist Periodic Mai
Page 175 and 176: Phone Numbers and How To Get Assist
Page 177 and 178: Disclaimers Warranty No agent, empl
Page 179 and 180: 0070-10-0683 Rev J January 11, 2011
show all

Datascope - Mindray

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?