2Gb: x4, x8, x16 DDR3 SDRAM - Micron

More documents

Recommendations

Info

Slew Rate Definitions for Differential Input Signals Input slew rate for differential signals (CK, CK# and DQS, DQS#) are defined and measured, as shown in Table 31 and Figure 20. The nominal slew rate for a rising signal is defined as the slew rate between V IL,diff,max and V IH,diff,min. The nominal slew rate for a falling signal is defined as the slew rate between V IH,diff,min and V IL,diff,max. Table 31: Differential Input Slew Rate Definition Differential Input Slew Rates (Linear Signals) Measured Input Edge From To CK and DQS reference Calculation Rising V IL,diff,max V IH,diff,min VIH,diff,min - V IL,diff,max �TR diff Falling V IH,diff,min V IL,diff,max VIH,diff,min - V IL,diff,max �TF diff Figure 20: Nominal Differential Input Slew Rate Definition for DQS, DQS# and CK, CK# Differential input voltage (DQS, DQS#; CK, CK#) �TF diff 2Gb: x4, x8, x16 DDR3 SDRAM Electrical Specifications – DC and AC �TR diff V IH,diff,min 0 V IL,diff,max PDF: 09005aef826aaadc 2Gb_DDR3_SDRAM.pdf – Rev. P 2/12 EN 54 Micron Technology, Inc. reserves the right to change products or specifications without notice. � 2006 Micron Technology, Inc. All rights reserved.
ODT Characteristics Figure 21: ODT Levels and I-V Characteristics The ODT effective resistance RTT is defined by MR1[9, 6, and 2]. ODT is applied to the DQ, DM, DQS, DQS#, and TDQS, TDQS# balls (x8 devices only). The ODT target values and a functional representation are listed in Table 32 and Table 33 (page 56). The individual pull-up and pull-down resistors (RTT(PU) and RTT(PD)) are defined as follows: • RTT(PU) = (VDDQ - VOUT)/|IOUT|, under the condition that RTT(PD) is turned off • RTT(PD) = (VOUT)/|IOUT|, under the condition that RTT(PU) is turned off To other circuitry such as RCV, . . . Chip in termination mode ODT I PU R TT(PU) R TT(PD) Table 32: On-Die Termination DC Electrical Characteristics I PD V DDQ I OUT = I PD - I PU Parameter/Condition Symbol Min Nom Max Unit Notes RTT effective impedance RTT(EFF) See Table 33 (page 56) 1, 2 Deviation of VM with respect to VDDQ/2 �VM –5 5 % 1, 2, 3 Notes: 1. Tolerance limits are applicable after proper ZQ calibration has been performed at a stable temperature and voltage (V DDQ = V DD, V SSQ = V SS). Refer to ODT Sensitivity (page 57) if either the temperature or voltage changes after calibration. 2. Measurement definition for R TT: Apply V IH(AC) to pin under test and measure current I[V IH(AC)], then apply V IL(AC) to pin under test and measure current I[V IL(AC)]: R TT = V IH(AC) - V IL(AC) I(V IH(AC) ) - I(V IL(AC) ) I OUT DQ V OUT V SSQ 3. Measure voltage (VM) at the tested pin with no load: �VM = 2 × VM VDDQ – 1 × 100 2Gb: x4, x8, x16 DDR3 SDRAM ODT Characteristics 4. For IT and AT devices, the minimum values are derated by 6% when the device operates between –40°C and 0°C (T C). PDF: 09005aef826aaadc 2Gb_DDR3_SDRAM.pdf – Rev. P 2/12 EN 55 Micron Technology, Inc. reserves the right to change products or specifications without notice. � 2006 Micron Technology, Inc. All rights reserved.
Page 1 and 2:
DDR3 SDRAM MT41J512M4 - 64 Meg x 4
Page 3 and 4: 2Gb: x4, x8, x16 DDR3 SDRAM Feature
Page 11 and 12: State Diagram Figure 2: Simplified
Page 13 and 14: 2Gb: x4, x8, x16 DDR3 SDRAM Functio
Page 15 and 16: Figure 4: 256 Meg x 8 Functional Bl
Page 17 and 18: Figure 7: 96-Ball FBGA - x16 (Top V
Page 19 and 20: Table 3: 78-Ball FBGA - x4, x8 Ball
Page 21 and 22: Table 4: 96-Ball FBGA - x16 Ball De
Page 23 and 24: Figure 9: 78-Ball FBGA - x4, x8 (HX
Page 25 and 26: Figure 11: 96-Ball FBGA - x16 (JT)
Page 27 and 28: Input/Output Capacitance Table 6: D
Page 29 and 30: Figure 12: Thermal Measurement Poin
Page 31 and 32: Table 9: I DD0 Measurement Loop CK,
Page 33 and 34: 2Gb: x4, x8, x16 DDR3 SDRAM Electri
Page 35 and 36: Table 14: I DD4R Measurement Loop C
Page 37 and 38: Table 16: I DD5B Measurement Loop C
Page 39 and 40: Table 18: I DD7 Measurement Loop CK
Page 41 and 42: Electrical Characteristics - I DD S
Page 43 and 44: Table 21: I DD Maximum Limits - Die
Page 45 and 46: Electrical Specifications - DC and
Page 47 and 48: Figure 13: Input Signal 0.925V 0.85
Page 49 and 50: Table 28: Differential Input Operat
Page 51 and 52: Figure 18: Definition of Differenti
Page 53: Figure 19: Nominal Slew Rate Defini
Page 57 and 58: Table 33: R TT Effective Impedances
Page 59 and 60: Figure 23: t AON and t AOF Definiti
Page 61 and 62: Output Driver Impedance Figure 26:
Page 63 and 64: 34 Ohm Driver The 34� driver’s
Page 65 and 66: Alternative 40 Ohm Driver Table 45:
Page 67 and 68: Output Characteristics and Operatin
Page 69 and 70: Figure 28: Differential Output Sign
Page 71 and 72: Slew Rate Definitions for Different
Page 73 and 74: Table 53: DDR3-1333 Speed Bins DDR3
Page 75 and 76: Table 55: DDR3-1866 Speed Bins DDR3
Page 77 and 78: PDF: 09005aef826aaadc Micron Techno
Page 97 and 98: 2Gb: x4, x8, x16 DDR3 SDRAM Command
Page 99 and 100: Table 62: Derating Values for t IS/
Page 101 and 102: Figure 32: Nominal Slew Rate and t
Page 103 and 104: Figure 34: Tangent Line for t IS (C
Page 105 and 106:
Data Setup, Hold, and Derating 2Gb:
Page 107 and 108:
Table 68: Derating Values for t DS/
Page 109 and 110:
2Gb: x4, x8, x16 DDR3 SDRAM Data Se
Page 111 and 112:
Figure 37: Nominal Slew Rate for t
Page 113 and 114:
Figure 39: Tangent Line for t DH (D
Page 115 and 116:
2Gb: x4, x8, x16 DDR3 SDRAM Command
Page 117 and 118:
Commands DESELECT NO OPERATION ZQ C
Page 119 and 120:
PRECHARGE REFRESH 2Gb: x4, x8, x16
Page 121 and 122:
DLL Disable Mode • All other self
Page 123 and 124:
Figure 42: DLL Disable Mode to DLL
Page 125 and 126:
Input Clock Frequency Change 2Gb: x
Page 127 and 128:
Write Leveling Figure 45: Write Lev
Page 129 and 130:
Write Leveling Procedure 2Gb: x4, x
Page 131 and 132:
Write Leveling Mode Exit Procedure
Page 133 and 134:
Figure 48: Initialization Sequence
Page 135 and 136:
Figure 50: MRS to nonMRS Command Ti
Page 137 and 138:
Table 77: Burst Order Burst Length
Page 139 and 140:
Mode Register 1 (MR1) Figure 53: Mo
Page 141 and 142:
On-Die Termination (ODT) WRITE LEVE
Page 143 and 144:
Mode Register 2 (MR2) Figure 55: Mo
Page 145 and 146:
SRT versus ASR 2Gb: x4, x8, x16 DDR
Page 147 and 148:
Figure 58: MPR Block Diagram Memory
Page 149 and 150:
PDF: 09005aef826aaadc Micron Techno
Page 151 and 152:
Page 153 and 154:
MPR Read Predefined Pattern The pre
Page 155 and 156:
ACTIVATE Operation Before any READ
Page 157 and 158:
READ Operation Figure 66: READ Late
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
2Gb: x4, x8, x16 DDR3 SDRAM READ Op
Page 165 and 166:
Figure 77: Data Strobe Timing - REA
Page 167 and 168:
Figure 80: t RPST Timing CK CK# DQS
Page 169 and 170:
Figure 81: t WPRE Timing Figure 82:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Figure 90: WRITE (BL8) to PRECHARGE
Page 177 and 178:
Figure 93: Data Input Timing DQS, D
Page 179 and 180:
Figure 94: Self Refresh Entry/Exit
Page 181 and 182:
Power-Down Mode Power-down is synch
Page 183 and 184:
Figure 95: Active Power-Down Entry
Page 185 and 186:
Figure 98: Power-Down Entry After R
Page 187 and 188:
Figure 102: ACTIVATE to Power-Down
Page 189 and 190:
RESET Operation 2Gb: x4, x8, x16 DD
Page 191 and 192:
On-Die Termination (ODT) Figure 107
Page 193 and 194:
Dynamic ODT Dynamic ODT Special Use
Page 195 and 196:
Table 89: Mode Registers for R TT(W
Page 197 and 198:
Page 199 and 200:
Synchronous ODT Mode ODT Latency an
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
show all

2Gb: x4, x8, x16 DDR3 SDRAM - Micron

Create successful ePaper yourself

Delete template?

Save as template?