27th Edition RHFS Product Guide - Ryan Herco Flow Solutions

ALL-PLASTIC METERING PUMPCALIBRATION COLUMNSFEATURES• Calibration columns are an easyto use method for determiningmetering pump flow rate usingindustry standard graduations ofmilliliters/minute and gallons/hour.• An equal starting point for bothgraduated scales gives theoperator both ml/min. and GPH inone test.• High contrast blue letteringenhances readability in all lightconditions, and all scales havea protective mylar lamination toprotect against chemical attack.• All sizes feature ruggedconstruction using industrial gradePVC fittings.590.900.250ORDER INFORMATION:5880.(Size No.) ALL-PLASTIC CALIBRATION COLUMNSColumnDiameter(in.)OPERATING INSTRUCTIONS1. Install calibration column on the suction side of pump as shown on the drawing.2. With valve A open and the pump operating, open valve B slowly until fluid level reaches the0 mark.3. Close valve A and begin timing with a stopwatch or wristwatch secondhand.4. At the one minute mark, observe the fluid level. This is the actual pump flow rate in ml/min.and GPH.5. When not in use calibration column should be drained, valve B closed, and valve A opened.SAF-T-FLO CHEMICAL INJECTION NOZZLESFEATURES• Flow instantly stopped in both directions upondisconnection.• No harmful spray, leak or spillage of chemicals.• Safely transfer highly toxic and corrosivechemicals.• Waterline connection has built-in ball checkvalve to prevent back flow from waterline intochemical reservoir.• Water treatment engineers and plant operatorsnow have an injection nozzle specifically designedto safely inject sodium hypochlorite and othercorrosive chemicals without leakage, sprayingor spillage of the chemical being transferred.After years of research and development,working with engineers and plant operators, thisinjection nozzle has been developed specificallyfor the water treatment industry. Until nowengineers and plant operators had to deal witha bronze heavy duty corporate stop with PVCtubing that is difficult to use. It may leak or sprayOverallLength(in.)SizeNo.Size(ml) GPHConnectionsFNPTPriceEach002 1 100 0 - 1.5 1/2 12-1/2 $51.48004 1-1/4 250 0 - 4 1/2 16-1/4 58.08008 2 500 0 - 8 3/4 16 64.68016 2 1000 0 - 16 3/4 25 72.60032 3 2000 0 - 32 1 24 170.28064 3-1/2 40000 0 - 64 1 34 187.44the operator and or equipment with chemicalfluid and could possibly “take off” if not properlysecured.• The injection nozzle has a special valve thatinstantly stops the flow of chemical fluid in bothdirections upon disconnection.APPLICATIONS• Water treatment.• Chemical injection.• Wastewater treatment.• Pump stations.• Safe alternative to corporate stops.SPECIFICATIONS• Available in PVC or 304 SS.• Wetted materials of construction: PVC/ Viton/Hastelloy C or 304 SS/ EPDM. Six inch nozzlelength standard.• Chemical supply end: 1/2” MNPT standard.• Nozzle insertion end: 3/4” MNPT standard.ALSO AVAILABLELMI ELECTRONICMETERING PUMPSSaf-T-Flo chemical injectionnozzles are also ideal for usewith LMI electronic meteringpumps, found on pages 424-426.ORDER INFORMATION6033.100 PVC CHEMICAL INJECTION NOZZLE Hastelloy C Spring,PTFE Teflon Ball & Seat, 150 PSI Working Pressure6033.200 304 SS CHEMICAL INJECTION NOZZLE SS Spring, PTFETeflon Ball & Seat, 250 PSI Working Pressure$369.08281.48590.900.2301-800-848-1141www.rhfs.com417