27th Edition RHFS Product Guide - Ryan Herco Flow Solutions

Ryan Herco Logo-4 Color ProcessElement: Placed Monotone EPSF o nt: Univers BlackMedium: Max size 21”X3.9”C=87, M=13, Y=2, K=1C=0, M=0, Y=0, K=72LIGHT-DUTY MIXERSIMPELLERIntended for flat-bottom tanks, this impellerdesign provides general-purpose mixing at amodest cost. The shaft and impeller are made of304 SS. The impeller diameters vary dependingon the shaft size. Neoprene is also available,while 316 SS is optional.PROPELLERDesigned for dished-bottom tanks or clampmount, the propeller creates down directionalflow patterns for thorough mixing. The shaftand propeller are made of 304 SS (316 SS isoptional). The standard diameter is 4”.CLAMP-MOUNT MIXERModel 6650-105 shown.FEATURES• C-clamp configurationenables these mixers tobe fastened to the sideof the tank. The clampmechanism offers a fourpositionadjustment thatdetermines the depth ofthe shaft into the tank.The motors run at 1725RPM, 120 VAC, 60 Hz.240 VAC motors areoptional.• NOTE: Clamp mountmixers have two clampsexcept 6650.025.BRACKET-MOUNT MIXERFEATURES• Two steel L-bracketssupport the motor of thesebracket-mount mixers.The bracket base hasfour holes for mountingto any flat surface, tankcover or brace. The 1725RPM motor is availablein either open frame orTEFC. Both run at 120VAC, 60 Hz. 240 VACmotors are optional.828.130.110 TEFC Motor828.130.120 Open MotorORDER INFORMATION:1/20 HP MIXER: Mixer blade and 5/16” x 28” long shaft are made of stainless steel.6650.025 MIXER, TEFC motor with propeller $322.351/3 HP MIXER: Mixer blade and 1/2” x 36” long shaft are made of stainless steel.6650.038 MIXER, Open motor with propeller 520.806650.338 MIXER, TEFC motor with propeller 669.901/2 HP MIXER: Mixer blade and 1/2” x 36” long shaft are made of stainless steel.6650.055 MIXER, Open motor with propeller 687.756650.355 MIXER, TEFC motor with propeller 771.751 HP MIXER: Mixer blade and 5/8” x 44” long shaft are made of stainless steel.6650.105 MIXER, Open motor with propeller 1,124.556650.405 MIXER, TEFC motor with propeller 1,120.35828.120.110 TEFC Motor828.120.120 Open MotorORDER INFORMATION:1/3 HP MIXERS: Mixer blade and 1/2” x 36” long shaft are made of stainless steel.6650.233 MIXER, Open motor with impeller $375.906650.234 MIXER, TEFC motor with impeller 531.306650.238 MIXER, Open motor with propeller 459.906650.239 MIXER, TEFC motor with propeller 614.251/2 HP MIXERS: Mixer blade and 1/2” x 36” long shaft are made of stainless steel.6650.250 MIXER, Open motor with impeller 479.856650.251 MIXER, TEFC motor with impeller 575.406650.255 MIXER, Open motor with propeller 621.606650.256 MIXER, TEFC motor with propeller 716.101 HP MIXERS: Mixer blade and 5/8” x 44” long shaft are made of stainless steel.6650.270 MIXER, Open motor with impeller 802.206650.271 MIXER, TEFC motor with impeller 801.156650.277 MIXER, Open motor with propeller 952.356650.278 MIXER, TEFC motor with propeller 1,059.45GEAR-REDUCTION-DRIVE MIXERFEATURES• The low RPM of these mixers makes them well-adjustedwhere added torque is required. A bracket-mount motor of1/4, 1/3 or 1/2 horsepower will handle light-viscosity fluids withspecific gravity less than 2.0. The TEFC motors run at 120VAC, 60 Hz and are geared to 60 RPM.ORDER INFORMATION:6651.125 MIXER, 1/4 Hp with 5/8” x 44” long shaft $1,535.39and one 14” diameter impeller6651.133 MIXER, 1/3 Hp with 5/8” x 44” long shaft 1,525.18and two 14” dia. impellers6651.150 MIXER, 1/2 Hp with 5/8” x 44” long shaft 1,703.24and three 14” dia. impellers828.110.110 AllOPTIONAL FEATURESEPOXY COATING: Has a special corrosion-resistant coating forthe stainless shaft and impeller.MOTORS: Explosion-proof or 230 VAC is available for 1/3, 1/2 and1 horsepower sizes.SHAFTS: Different lengths are available on special order.SHAFT-TO-MOTOR COUPLINGS are available in optional sizes.APPLICATION SUGGESTIONS for LIGHT-VISCOSITYliquids. Conservative sizing is recommended.Horsepower1/201/41/31/21Tank Size (gal.)Light Mixing Medium Mixing Heavy Mixing6040201501005020014080300200100500300200580