27th Edition RHFS Product Guide - Ryan Herco Flow Solutions

Ryan Herco Logo-4 Color ProcessElement: Placed Monotone EPSF o nt: Univers BlackMedium: Max size 21”X3.9”C=87, M=13, Y=2, K=1C=0, M=0, Y=0, K=72MICROPUMP GEAR PUMPHEADSCAVITY-STYLE PUMP HEADSFEATURES• Ideal for applications requiringfrequent cycling, suction lift, andhigh output pressures up to 4700ml/min.• Drive magnets are encapsulatedin 316 SS and Teflon ® PTFE fordurability and chemical resistance.• Economical, easy to clean andservice, and provide suction liftcapabilities.• Cavity-style pump heads dependon the surrounding pressure in theORDER: CAVITY-STYLE STANDARD PUMP HEADmagnet cup cavity to hold the gearstightly together and often use helicalgears composed of extremely lowfriction material-such as Teflon ® .SPECIFICATIONS• Duty cycle: Continuous 150 to 5000RPM.• Suction lift: 1 ft.• Viscosity: 200 cp.• Port size: 1/8 FNPT.• Particulates: None.• Run dry: Under 30 seconds.• Reversible: Yes.* Flow rate based on 150 to 5000 RPM (recommended continuous duty speeds) with water and no back pressure.† Up to 210°F using the high temperature seals below. For Intermittent duty only.Model 6060.000 Pump Head shown.Combine pump head above with drive onpage 451 to form system.Part No.ml/revFlow rate*(ml/min) MinFlow rate*(ml/min) MaxMax.System psiMax.Diff. psiWettedParts BodyWetted PartsGearsWettedParts SealMax.RPM†TemperatureRangeReliefValuePriceEach6069.000 0.32 48 1600 300 45 316SS Teflon PTFE Teflon PTFE 9000 -50 to 210°F Yes $532.006060.000 0.64 96 3200 300 45 316SS Teflon PTFE Teflon PTFE 9000 -50 to 130°F Yes 532.006068.000 0.94 141 4700 300 45 316SS Teflon PTFE Teflon PTFE 9000 -50 to 130°F Yes 532.00600.310.110PRESSURE-LOADED PUMP HEADSFEATURES• Provide nominal flow rates from 2.6to 5450 ml/min under continuousduty (see table below).• All models give you the increasedvolumetric efficiency for consistentflow rates.• Allow for increased volumetricefficiency, using a suction shoeto force the fluid pressure in themagnet cup to seal the gears tightlytogether.• Ensure complete fluid transfer withno backflow or leakage betweengear tips.• As the discharged pressure onthe suction shoe and mesh pointincreases, so does the efficiency ofthe pump. The pressure on the outletside forces the suction shoe and gearstogether, as long as the outlet pressureis greater than the pressure on theinlet. This guarantees complete fluidtransport through the pump head.SPECIFICATIONS• Duty cycle: Continuous 150 to 5000RPM.• Suction lift: 1 ft.• Viscosity: 100 cP.• Port size: 1/8 FNPT.• Particulates: None.• Run dry: Under 30 seconds.• Reversible: No.Model 6074.000 Pump Head shown.Combine pump head above with drive onpage 451 to form system.ORDER: PRESSURE LOADED STANDARD PUMP HEADSPart No.ml/revFlow rate*(ml/min) MinFlow rate*(ml/min) MaxMax.System psiMax. Diff.psiWettedParts BodyWettedParts GearsWettedParts SealMax.RPM†TemperatureRangeReliefValuePriceEach6056.000 0.017 2.6 85 300 50 316 SS Graphite Teflon PTFE 9000 -50 to 250°F No $574.006057.100 0.042 6.2 210 300 50 316 SS Graphite Teflon PTFE 9000 -50 to 250°F Yes 574.006058.000 0.084 12.6 420 300 50 316 SS Graphite Teflon PTFE 9000 -50 to 250°F Yes 540.006073.000 0.092 13.8 460 300 50 316 SS PPS Teflon PTFE 9000 -50 to 210°F No 505.006074.000 0.564 84.6 2820 300 50 316 SS PPS Viton 8000 -50 to 210°F Yes 545.006075.000 1.09 163.5 5450 300 45 316 SS PPS Viton 9000 -40 to 250°F Yes 664.00* Flow rate based on 150 to 5000 RPM operation (recommended continuous duty speeds) with water and no back pressure.† For Intermittent duty only.600.310.150600.310.120452