27th Edition RHFS Product Guide - Ryan Herco Flow Solutions

MASTERFLEX ® TUBINGPUMP SYSTEMSINDUSTRIAL/PROCESS PUMP HEADSEASY-LOAD I/P PUMP HEADFEATURES• Fluid pumped only contacts tubing ID.• Designed for fast tubing changes.• Delivers flow rates up to 13 LPM (3.5 GPM).• Adjustable occlusion; standard 3-roller pulselessdelivery.• Designed for 26, 73, and 82 tubing sizes.• Multi-channel pumping.• Polysulfone or Polyphenylene sulfide headmaterial.ORDER: 6007.(Size No.) EASY LOADINDUSTRIAL/PROCESS PUMP HEADSizeNo. Fits Tubing SizesHeadMt’l. RotorsPriceEach000 26,73,82 PSF CRS $472.50001 26,73,82 PSF SS 665.00003 26,73,82 PPS CRS 702.50005 26,73,82 PPS SS 727.50Above compatible with drives found below on this page.580.130.120INDUSTRIAL/PROCESS PUMP DRIVESANALOG MICROPROCESSOR OR DIGITAL SYSTEM – Flowsto 3.5 GPMModel 6009.320 digitalwall mount.Model 6009.340analog benchtop.Microprocessor drive units shown with pump heads and tubing which are soldseparately.MICROPROCESSOR CONTROLLERDigital system features a membrane keypad, analog systemfeatures switch and a rotary dial. The back panel, dry contactclosure allows remote control of start/stop functions using theoptional footswitch (model 6009.320 only). Wall-mount controllers(models 6009.320 & .350) include a six-foot cable for easyconnection to the motor. Both benchtop and wall-mount controllerscome standard with a six-foot power cord.FEATURES• Benchtop controller or NEMA-13 configurations.• NEMA-4X “washdown motors.”• Flow rate 0.03 to 3.5 GPM.• Flow accuracy ±0.5%.• Speed regulation better than ±0.3%.• Torque overload protection.• Dispensing/copy mode available on model 6009.320.• Remote operation available on model 6009.320.• This new modular design makes Masterflex Process (I/P)drive systems compact and lightweight. Both benchtop andNEMA Type 13 “wash-down” systems feature a NEMA-4Xpermanent magnet, 1/5 hp motor with planetary gear head.The motor measures 13.75” x 5.5” x 5.75”, and it acceptsup to two Masterflex Process pump heads in either theStandard I/P or I/P Easy Load configurations.DISPENSING (6009.320 only)Simplify repetitive dispensing by filling the trial dispensesample, then pressing the dispense/copy button. Allsubsequent samples will be dispensed in the exact quantityof the first sample.ORDER: 6009.(Size No.) INDUSTRIAL/PROCESSPUMP DRIVESizeNo.RpmRangeControllerTypeMax HeadAccepted VAC (50-60 Hz)PriceEachMICROPROCESSOR/DIGITAL SYSTEMS320 20 - 650 Nema- 13 2 115 $2,156.25ANALOG SYSTEMS350 20 - 650 Benchtop 2 115 2,376.25340 20 - 650 Nema- 13 2 115 1,727.50Prices include pump drive and controller. Pump heads sold separately, see above.I/P .26 I/P .73 I/P .82580.140.140 -320580.140.110 -340580.140.120 -350Tubing Cross SectionsInside diameter†: in. (mm)Hose barb Size†: in. (mm)0.25 (6.4)1/4 (6.4)0.37 (9.5)3/8 (9.5)0.5 (12.7)1/2 (12.7)Flow range†† with 6 to 600 rpm drive: ml/minValue in ( ) obtained with high-performance pump head0.12 to 4 LPM(0.03 to 1.1 GPM)0.2 to 8 LPM(0.05 to 2.1 GPM)0.4 to 13 LPM(0.1 to 3.5 GPM)Maximum pressure, continuous**Maximum pressure, intermittent**Maximum vacuum**Suction lift20 psig (1.7 bar)40 psig (2.7 bar)25 psig (1.7 bar)40 psig (2.7 bar)26” Hg (660mm Hg)29ft H 2O (8.8 mH 2O)10 psig (0.7 bar)20 psig (1.4 bar)20” Hg (510mm Hg)23ft H 2O (7.3 mH 2O)†† Flow ranges are approximate – calculated under the following conditions: 0 PSIG at inlet, 0.5 PSIG at outlet: water at 72°F (22°C).† Determined under the following conditions: 0 PSI at inlet, 0.5 PSI at outlet; water circulent at 72°F (22°C).** Actual performance varies depending on tubing formulation – values shown are for firm tubing.1-800-848-1141www.rhfs.com435