HP 8590 E & L Series Spectrum Analyzers and HP 8591C Cable TV ...

More documents

Recommendations

Info

Connecting a LaserJet Printer able G2. Setting of RS-232 Switches 1 Switch 1 Setting - 1 Comments 1 Number 1 I I 1 IUD 1 DTR. I ‘Ihble C-3. Setting the Baud Rate Baud Setting for Setting for Rate Switch 4 Switch 5 1200 up up 2400 up down 9600 down down ‘lb connect an HP LaserJet printer to the spectrum analyzer, use the information in Figure C-7. LaserJet 4P/4MP AnOlYZer RTS 1 TxD 2 RxD 3 DSR 4 GND 5 DTR 6 nc 7 DTR 6 nc 9 > > 1 DCD > > 2 RxD ( < 3 TxD < < 4 DTR < < 5 GND > > 6 DSR ---opt ionol--- 7 RTS > > 0 CTS ---ootionol--- 7 RI Figure G7. HP C2932A g-pin to g-pin LaserJet Printer Connection cu139e RS-232 and Parallel Option 043 C-5
Connecting a Modem To connect a modem to the spectrum analyzer, use the information in Figure C-8. The connection is for a Hayes 1200 Modem and the spectrum analyzer. System Settings Modem Allalyzer TxD 2 RrD 3 RTS 4 CTS 5 DSR 6 GND 7 DCD 8 DTR 20 RI 22 < < 3 TxD > > 2 RxD < > 7 RTS \ > 8 CTS < > 6 DSR < < 5 GND > > 1 DCD < < 4 DTR no connection 9 RI Figure C-8. 25-pin to g-pin Modem Connection Select 1200 baud for both the modem and the spectrum analyzer. Connecting an HP-GL Plotter ‘Lb connect an HP-GL plotter to the spectrum analyzer, use the information in Figure C-9. Switch Settings Plotter Atlalvzer GND 1 TxD 2 RxD 3 RTS 4 CTS 5 DSR 6 GND 7 DTR 20 < > 1 GND > > 3 RxD < < 2 TxD 8 DCD F *O DTR < 7 GND > > 5 CTS Figure C-9. HP-GL Plotter Connection cu140e Set the switches on the HP-GL plotter to the following settings. Set the baud rate of the plotter and spectrum analyzer to the same value. After setting the switch positions, turn plotter off, then on again. C-6 M-232 and Parallel Option 043 Switch Position Switch Position Expand: 4 Parity: ) (Off) Emulate: 1 Even/Odd: ) (Odd) Stand-alone: 4 Duplex: ) (Full) Monitor Mode: ) (normal) Hardwire: I Local ) (normal) DTR-Bypass: ) (normal) cul13e
Page 1 and 2:
Title & Document Type: Manual Part
Page 3 and 4:
Notice. The information contained i
Page 5 and 6:
Assistance Product maintenance agre
Page 7 and 8:
How to Use This Guide This guide us
Page 9 and 10:
Contents 1. Preparing for Use What
Page 11 and 12:
4. Creating and Using Downloadable
Page 13 and 14:
COMPRESS Compress Trace . . . . . .
Page 15 and 16:
LSPAN Last Span . . . . . . . . . .
Page 17 and 18:
RLPOS Reference-Level Position . .
Page 19 and 20:
Xhbles l-l. Setting of HP ThinkJet
Page 21 and 22:
Connecting the Computer to the Spec
Page 23 and 24:
Test Program To test the connection
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Test Program The program shown belo
Page 31 and 32:
Note Because HP-IB cables can be co
Page 33 and 34:
Plotting Using an HP-IB Interface N
Page 35 and 36:
Printing Using an RS-232 Interface
Page 37 and 38:
Plotting Using an RS-232 Interface
Page 39 and 40:
Printing Using a Parallel Interface
Page 41 and 42:
Plotting to an HP LaserJet Printer
Page 43 and 44:
If There Is a Problem This section
Page 45 and 46:
Writing Your First Program When the
Page 47 and 48:
Modifying the Program Remote operat
Page 49 and 50:
Enhancing the Program with Variable
Page 51 and 52:
Getting Information from the Spectr
Page 53 and 54:
Programming Guidelines 1. Perform t
Page 55 and 56:
Controlling Trace Data with a Compu
Page 57 and 58:
Saving Trace Data The trace data in
Page 59 and 60:
Reading Trace Data from a Computer
Page 61 and 62:
Program Example for the HP-IB Inter
Page 63 and 64:
Program Example for the RS-232 Inte
Page 65 and 66:
Returning the Spectrum Analyzer to
Page 67 and 68:
350 GOSUB 500 360 TR3$=TR6$ 370 12=
Page 69 and 70:
330 OUTPUT @Sa;"MKPK HI; TS;" 340 O
Page 71 and 72:
Program Example for the RS-232 Inte
Page 73 and 74:
Different Formats for Trace Data Tr
Page 75 and 76:
B Format The B format allows you to
Page 77 and 78:
A-Block Format The A-block format i
Page 79 and 80:
M Format The M format is for sendin
Page 81 and 82:
Trace Data Format TDF P TDF B TDF A
Page 83 and 84:
Creating a DLP This section contain
Page 85 and 86:
To Use a User-Defined Variable with
Page 87 and 88:
To Enter Values into a DLP To allow
Page 89 and 90:
File name Date and author's name Pr
Page 91 and 92:
Storing DLPs on a RAM Card If the s
Page 93 and 94:
Determining the Amount of Memory Ne
Page 95 and 96:
‘lb Delete a DIP from Spectrum An
Page 97 and 98:
‘Ib Access the DLP Editor . Press
Page 99 and 100:
lb Modify the DLP 1. If necessary,
Page 101 and 102:
DLP Programming Guidelines This sec
Page 103 and 104:
Programming Commands What You’ll
Page 105 and 106:
Syntax Elements are shown in the sy
Page 107 and 108:
In the syntax diagrams, characters
Page 109 and 110:
NONE NR Element NRM or NORMAL NTSC
Page 111 and 112:
The alternate commands (listed in t
Page 113 and 114:
This functional index categorizes t
Page 115 and 116:
Function Category :ALIBRATION :OMMA
Page 117 and 118:
Function Category ;RAPHICS NFORMATI
Page 119 and 120:
Function Category LIMIT LINES :cont
Page 121 and 122:
‘Ihble 5-4. Functional Index (con
Page 123 and 124:
Function Category MEASURE/USER Icon
Page 125 and 126:
Function Category RECALL or SAVE lP
Page 127 and 128:
Function Category 3WEEP (continued)
Page 129 and 130:
RIGGER Function Category JSER-DEFIN
Page 131 and 132:
ABORT Abort Stops the execution all
Page 133 and 134:
ABS Absolute Places the absolute va
Page 135 and 136:
ACP Adjacent Channel Power Performs
Page 137 and 138:
ACPBW Channel Bandwidth ACPBW Chann
Page 139 and 140:
ACPCONTM Continuous Sweep Measureme
Page 141 and 142:
ACPE Adjacent Channel Power Extende
Page 143 and 144:
Setting the ACPGR to - 1, does the
Page 145 and 146:
ACPMK Adjacent Channel Power Marker
Page 147 and 148:
ACPPAR ACP Manual or Auto ‘able 5
Page 149 and 150:
ACPSP Channel Spacing Allows you to
Page 151 and 152:
ACTDEF Active Function Definition C
Page 153 and 154:
Example 2 ACTDEF Active Function De
Page 155 and 156:
ACTDEF Active Function Definition Q
Page 157 and 158:
ADD Add Adds the sources and sends
Page 159 and 160:
AMB Trace A Minus Trace B AMB Trace
Page 161 and 162:
Description AMB Trace A Minus Trace
Page 163 and 164:
Description AMBPL Trace A Minus Tra
Page 165 and 166:
80 OUTPUT 718;"AMPCOR?;" 90 ENTER 7
Page 167 and 168:
ANLGPLUS Analog Plus Turns on or of
Page 169 and 170:
ANNOT Annotation Turns on or off th
Page 171 and 172:
AT Attenuation Specifies the RF inp
Page 173 and 174:
AUNITS Amplitude Units Specifies th
Page 175 and 176:
AVG Average Averages the source and
Page 177 and 178:
AXB Exchange Trace A and Trace B Ex
Page 179 and 180:
Query Response baud rate / \ BAUDRA
Page 181 and 182:
Description The BIT places either a
Page 183 and 184:
Example 10 CLEAR 718 20 OUTPUT 718;
Page 185 and 186:
BML Trace B Minus Display Line Subt
Page 187 and 188:
BXC Trace B Exchange Trace C Exchan
Page 189 and 190:
Note Execute CAL STORE after succes
Page 191 and 192:
CAT Catalog Catalogs either spectru
Page 193 and 194:
Information File name File Type Dat
Page 195 and 196:
CF Center Frequency Specifies the c
Page 197 and 198:
CHP Channel Power Performs the chan
Page 199 and 200:
CHPGR Channel Power Graph On or Off
Page 201 and 202:
CLRBOX Clear Box Clears a rectangul
Page 203 and 204:
CLRDSP Clear Display Erases user-ge
Page 205 and 206:
CLS Clear Status Byte Clears all st
Page 207 and 208:
CNF Confidence ‘I&t Performs the
Page 209 and 210:
CNTLB Auxiliary Interface Control L
Page 211 and 212:
CNTLD Auxiliary Interface Control L
Page 213 and 214:
COMB Comb Turns on or off the comb
Page 215 and 216:
Example COMPRESS Compress Trace Thi
Page 217 and 218:
Example 10 OUTPUT 718;"IP;" 20 OUTP
Page 219 and 220:
CORREK Correction Factors On Return
Page 221 and 222:
CRTHPOS Horizontal Position of CRT
Page 223 and 224:
CTA Convert to Absolute Units CE4 C
Page 225 and 226:
CTM Convert to Measurement Units CT
Page 227 and 228:
OUTPUT 718;"MOV DA,D,ADDRESS;" OUTP
Page 229 and 230:
DATEMODE Date Mode DATEMODE Date Mo
Page 231 and 232:
DET Detection Mode Selects the spec
Page 233 and 234:
DISPOSE Dispose DISPOSE Dispose Fre
Page 235 and 236:
DIV Divide Divides source 1 by sour
Page 237 and 238:
DL Display Line DL Display Line Def
Page 239 and 240:
DN Down Reduces the active function
Page 241 and 242:
Description DONE Done As shown by t
Page 243 and 244:
DRAWBOX Draw Box Draws a rectangula
Page 245 and 246:
DSPLY Display Displays the value of
Page 247 and 248:
DT Define Terminator DT Define Term
Page 249 and 250:
Description Unlike enter parameter
Page 251 and 252:
ENTER Enter From HP-IB Allows the s
Page 253 and 254:
EP Enter Parameter Function EP Ente
Page 255 and 256:
EXP Exponent Places the exponential
Page 257 and 258:
Description EXP Exponent The EXP co
Page 259 and 260:
Description FA Start Frequency The
Page 261 and 262:
Description FB Stop Frequency The F
Page 263 and 264:
OUTPUT 718;"FFT TRA,TRA,TRB;VIEW TR
Page 265 and 266:
80 .90 00 0 -10 -20 -30 -40 VI -A -
Page 267 and 268:
FFTAUTO Marker to Auto FFT “Measu
Page 269 and 270:
FFTCONTS FFT Continuous Sweep Perfo
Page 271 and 272:
FFTMM FFT Marker to Midscreen FBTMM
Page 273 and 274:
FFTOFF FFTOff Exits the fast Fourie
Page 275 and 276:
FFTPCTAMR FFT Percent Amplitude Mod
Page 277 and 278:
FFTSNGLS uses the following when pe
Page 279 and 280:
FFTSTOP FFT Stop Frequency Sets the
Page 281 and 282:
FMGAIN FM Gain Sets the total FM fr
Page 283 and 284:
Description FOFFSET Frequency Offse
Page 285 and 286:
FS Full Span Sets the frequency spa
Page 287 and 288:
Example Connect CAL OUT to the spec
Page 289 and 290:
GATECTL Gate Control GATECTL Gate C
Page 291 and 292:
GD Gate Delay Sets the delay time f
Page 293 and 294:
GDRVGDEL Gate Delay for the Frequen
Page 295 and 296:
GDRVGLEN Gate Length for the Freque
Page 297 and 298:
Query Response 7< r off 7 0 I outpu
Page 299 and 300:
Query Response GDRVGTIM Gate Trigge
Page 301 and 302:
Query Response GDRVPRI returns the
Page 303 and 304:
Query Response GDRVPWID returns the
Page 305 and 306:
Query Response GDRVRBW Couple Resol
Page 307 and 308:
Query Response r e f e r e n c e /
Page 309 and 310:
Query Response GDRVST Couple Sweep
Page 311 and 312:
GDRVSWDE Delay Sweep for Time Windo
Page 313 and 314:
GDRVSWP Sweep Time for the Time Win
Page 315 and 316:
GDRVUTIL Gate Utility Turns on or o
Page 317 and 318:
GDRVVBW Couple Video Bandwidth to G
Page 319 and 320:
GETPLOT Get Plot GETPLOT Get Plot I
Page 321 and 322:
GETPRNT Get Print GETPRNT Get Print
Page 323 and 324:
GL Gate Length Sets the length of t
Page 325 and 326:
GR Graph Graphs the given 9 coordin
Page 327 and 328:
HAVE Have Returns a “0” if the
Page 329 and 330:
I 3 Bit Position Bit Status = 0 Bit
Page 331 and 332:
HN Harmonic Number HN Harmonic Numb
Page 333 and 334:
HNLOCK Harmonic Number Lock Once HN
Page 335 and 336:
HNUNLK Unlock Harmonic Number Unloc
Page 337 and 338:
ID Identify Returns the spectrum an
Page 339 and 340:
Example IF TEEN ELSE ENDIF If Then
Page 341 and 342:
INT Integer INT Integer Places the
Page 343 and 344:
INZ Input Impedance Specifies the v
Page 345 and 346:
GD GDRVGDEL GDRVGLEN GDRVRBW GDRVST
Page 347 and 348:
IP Instrument Preset IP also clears
Page 349 and 350:
KEYCMD Key Command KEYCMD Key Comma
Page 351 and 352:
170 180 190 200 210 220 230 240 250
Page 353 and 354:
KEYDEF User-Defined Key Definition
Page 355 and 356:
Example 2 KEYDEF User-Defined Key D
Page 357 and 358:
KEYENH Key Enhance KEYENH Key Enhan
Page 359 and 360:
Example 2 KEYENH Key Enhance Use th
Page 361 and 362:
KEYENH Key Enhance Softkey numbers:
Page 363 and 364:
KEYLBL Key Label Relabels a softkey
Page 365 and 366:
LB Label LB Label Writes text (labe
Page 367 and 368:
LB Label ‘Ihble 5-6. Character Se
Page 369 and 370:
LF Base Band Instrument Preset Perf
Page 371 and 372:
LIMIDEL Delete Limit-Line Table Del
Page 373 and 374:
LIMIDISP Limit Line Display When us
Page 375 and 376:
Description LIMIFAIL returns one of
Page 377 and 378:
LIMIHI Upper Limit Allows you to sp
Page 379 and 380:
Description LIMILINE Limit Lines LI
Page 381 and 382:
LIMILO Lower Limit Allows you to sp
Page 383 and 384:
LIMIMODE Limit-Line Entry Mode LIMI
Page 385 and 386:
LIMIREL Relative Limit Lines Specif
Page 387 and 388:
LIMISEG Enter Limit-Line Segment fo
Page 389 and 390:
LIMISEG Enter Limit-Line Segment fo
Page 391 and 392:
Example OUTPUT 718;"LIMIDEL;" OUTPU
Page 393 and 394:
LIMITEST Enable Limit Line ‘&stin
Page 395 and 396:
LINFILL Line Fill Fills linear inte
Page 397 and 398:
LN Linear Scale LN Linear Scale Spe
Page 399 and 400:
LOAD Load File name: You must suppl
Page 401 and 402:
LOG Logarithm Prerequisite Commands
Page 403 and 404:
LSPAN Last Span Changes the spectru
Page 405 and 406:
MDS Measurement Data Size For this
Page 407 and 408:
Query Response base1 ine reference
Page 409 and 410:
MEANTH Trace Mean Above Threshold M
Page 411 and 412:
MEASOFF Measurement Off MEASOFF’
Page 413 and 414:
During this relative-amplitude mode
Page 415 and 416:
MENU Menu Selects and displays the
Page 417 and 418:
MERGE Merge Two Traces Merges the s
Page 419 and 420:
MF Marker Frequency Output Returns
Page 421 and 422:
MIN Minimum MIN Minimum Compares so
Page 423 and 424:
MINH Minimum Hold Updates trace C w
Page 425 and 426:
MIRROR Mirror Image Displays the mi
Page 427 and 428:
MKA Marker Amplitude MKA Marker Amp
Page 429 and 430:
MKACT Activate Marker Specifies the
Page 431 and 432:
MKBW Marker Bandwidth MKBW Marker B
Page 433 and 434:
MKCONT Marker Continue Resumes the
Page 435 and 436:
Description MKD Marker Delta The MK
Page 437 and 438:
Query Response de t a MKDLMODE Mark
Page 439 and 440:
Example MKF Marker Frequency OUTPUT
Page 441 and 442:
MKFCR Marker Counter Resolution Set
Page 443 and 444:
MKMIN Marker Minimum Moves the acti
Page 445 and 446:
Example 10 INPUT "ENTER IN THE STAR
Page 447 and 448:
Description MKNOISE Marker Noise Th
Page 449 and 450:
MKP Marker Position Places the acti
Page 451 and 452:
MKPAUSE Marker Pause Pauses the swe
Page 453 and 454:
MKPK Marker Peak Positions the acti
Page 455 and 456:
Query Response MKPX Marker Peak Exc
Page 457 and 458:
MKRRAD Marker Readout MKREAD Non-Ze
Page 459 and 460:
MKSP Marker to Span Sets the start
Page 461 and 462:
MKSTOP Marker Stop Stops the sweep
Page 463 and 464:
MKTBL Marker ‘able Restrictions T
Page 465 and 466:
MKTRACK Marker Track MKTRACK Marker
Page 467 and 468:
ML Mixer Level ML Mixer Level Speci
Page 469 and 470:
MOD Modulo Example 10 OUTPUT 718;"V
Page 471 and 472:
MOV Move Copies the source values i
Page 473 and 474:
MPY Multiply Multiplies the sources
Page 475 and 476:
MS1 Mass Storage Is Allows you to s
Page 477 and 478:
MXM Maximum Example 10 OUTPUT 718;"
Page 479 and 480:
M4 Marker Zoom Activates a single m
Page 481 and 482:
NDB Number of dB Specifies the dist
Page 483 and 484:
OUTPUT 718;“MOV NDBPNT,O;” Turn
Page 485 and 486:
NRL Normalized Reference Level Sets
Page 487 and 488:
OA Output Active Function Value Sen
Page 489 and 490:
OBW Occupied Bandwidth Variable or
Page 491 and 492:
OL Output Learn String Transmits in
Page 493 and 494:
ONCYCLE On Cycle Description The ON
Page 495 and 496:
ONDELAY On Delay Description The ON
Page 497 and 498:
ONEOS On End of Sweep Description R
Page 499 and 500:
ONMKR On Marker Query Response -+(
Page 501 and 502:
ONMKRU On Marker Update 330 OUTPUT
Page 503 and 504:
ONSRQ On Service Request Executes t
Page 505 and 506:
ONSWP On Sweep Executes the list of
Page 508 and 509:
Description ONTIME On Time Limit th
Page 510 and 511:
OUTPUT Output to Remote Port or Par
Page 512 and 513:
Description OUTPUT Output to Remote
Page 514 and 515:
3 . 2 5 0 GHz o,o ATTEN 1 0 dG Figu
Page 516 and 517:
‘Ihble 5-9. Spectrum Analyzer Sta
Page 518 and 519:
PCIAM Percent AM the PCTAM command
Page 520 and 521:
PD Pen Down PD Pen Down Instructs t
Page 522 and 523:
Example OUTPUT 718;"IP;SNGLS;" OUTP
Page 524 and 525:
Example PDF Probability Distributio
Page 526 and 527:
Example Connect CAL OUT to the spec
Page 528 and 529:
Query Response PEAKS Peaks Programm
Page 530 and 531:
Query Response peaks below peaks ab
Page 532 and 533:
PKRES Peak Result PKRES returns the
Page 534 and 535:
PKSORT Peak Sort PKSORT Peak Sort S
Page 536 and 537:
Query Response table PKTBL Peak ‘
Page 538 and 539:
PKZOOM Peak Zoom PKZOOM Peak Zoom A
Page 540 and 541:
PLOT Plot Initiates a plotter outpu
Page 542 and 543:
PLTPRT Plot Port PWPRT Plot Port Se
Page 544 and 545:
PP Preselector Peak Peaks the prese
Page 546 and 547:
PREAMPG External Preamplifier Gain
Page 548 and 549:
PRINT Print Initiates a output of t
Page 550 and 551:
PRNTADRS Print Address Allows you t
Page 552 and 553:
PSTATE Protect State PSTATE Protect
Page 554 and 555:
PURGE Purge. File Deletes the speci
Page 556 and 557:
Example DISP "CONNECT CAL OUT TO IN
Page 558 and 559:
RB Resolution Bandwidth Specifies t
Page 560 and 561:
RCLS Recall State RCLS Recall State
Page 562 and 563:
Description RCEI’ Recall Trace Th
Page 564 and 565:
REPEAT UNTIL Repeat Until The REPEA
Page 566 and 567:
RESETRL Reset Reference Level Reset
Page 568 and 569:
REV Revision RJW Revision Returns t
Page 570 and 571:
Description RL Reference Level The
Page 572 and 573:
RMS Root Mean Square Value Returns
Page 574 and 575:
RQS Service Request Mask Sets a bit
Page 576 and 577:
SAVEMENU Save Menu Saves menu 1 und
Page 578 and 579:
SAVET Save Trace !&WET Save Trace S
Page 580 and 581:
SAVRCLF Save or Recall Flag Indicat
Page 582 and 583:
Description SAVRCLN Save or Recall
Page 584 and 585:
SEGDEL Segment Delete Deletes the s
Page 586 and 587:
SENTER Segment Entry for Frequency
Page 588 and 589:
SENTER Segment Entry for Frequency
Page 590 and 591:
SENTERT Segment Entry for Sweep Tim
Page 592 and 593:
SER Serial Number Returns the seria
Page 594 and 595:
SETTIME Set Time Allows you to set
Page 596 and 597:
Example 10 OUTPUT 718;"IP;" 20 OUTP
Page 598 and 599:
SP Span Changes the total displayed
Page 600 and 601:
SPEAKER Speaker Turns on or off the
Page 602 and 603:
SQLCH Squelch Sets the squelch thre
Page 604 and 605:
Example OUTPUT 718 ; "SQR SP, lE8 ;
Page 606 and 607:
SRCALC Source Leveling Control Fbr
Page 608 and 609:
Description SRCAT Source Attenuator
Page 610 and 611:
Description SRCNORM Source Normaliz
Page 612 and 613:
SRCPSTP Source Power-Level Step Siz
Page 614 and 615:
SRCPSWP Source Power Sweep Selects
Page 616 and 617:
SRCPWR Source Power Selects the sou
Page 618 and 619:
SRCTK Source Tracking Adjusts the t
Page 620 and 621:
SRCTKPK Source Tracking Peak SRCTKP
Page 622 and 623:
Bit Number Decimal Equivalent 32 16
Page 624 and 625:
This displays the octal equivalent
Page 626 and 627:
Example 10 CLEAR 718 20 OUTPUT 718;
Page 628 and 629:
Query Response ST Sweep Time Progra
Page 630 and 631:
STDEV Standard Deviation of Trace A
Page 632 and 633:
STOR Store Stores data on a RAM car
Page 634 and 635:
Description STOR Store The STOR com
Page 636 and 637:
Example SUB Subtract OUTPUT 718;"SU
Page 638 and 639:
SUMSQR Sum of Squared Trace Amplitu
Page 641 and 642:
SYNCMODE Synchronize Mode Selects t
Page 643 and 644:
TA Transfer A Returns trace A ampli
Page 645 and 646:
TDF Trace Data Format Formats trace
Page 647 and 648:
TDF Trace Data Format Example of ho
Page 649 and 650:
!IDFB TDF Trace Data Format Descrip
Page 651 and 652:
TEXT lkxt Writes text on the spectr
Page 653 and 654:
TIMEDATE Time Date Allows you to se
Page 655 and 656:
TITLE Title Activates the screen ti
Page 657 and 658:
Query Response TM Trigger Mode QTM
Page 659 and 660:
TO1 Third-Order Intermodulation Mea
Page 661 and 662:
TRA/TRB/TRC Trace Data Input and Ou
Page 663 and 664:
TRCMEM Trace Memory TRCMEM Trace Me
Page 665 and 666:
Description TRDEF Trace Define The
Page 667 and 668:
TRGRPH Trace Graph Displays a compr
Page 669 and 670:
TRMATH Trace Math Executes a list o
Page 671 and 672: TRPRST Trace Preset Sets the trace
Page 673 and 674: TS Thke Sweep Starts and completes
Page 675 and 676: TVSFRM TV Frame Selects the type of
Page 677 and 678: TVSTND TV Standard Selects the trig
Page 679 and 680: TVSYNC TV Sync Selects the polarity
Page 681: UP UP Increases the value of the ac
Page 684 and 685: VARDEF Variable Definition Creates
Page 686 and 687: VARIANCE Variance of Trace Amplitud
Page 688 and 689: VAVG Video Average Enables the vide
Page 690 and 691: VB Video Bandwidth Query Response 5
Page 692 and 693: VIEW View Trace Displays trace A, t
Page 694 and 695: WINNEXT Window Next When using the
Page 696 and 697: WINON Window ON Displays the two wi
Page 698 and 699: WINZOOM Window Zoom When using the
Page 700 and 701: XCH Exchange Example OUTPUT 718;"XC
Page 702 and 703: ZMKCNTR Zone Marker at Center Frequ
Page 704 and 705: ZMKPKNR Zone Marker for Next Right
Page 706 and 707: ZMKSPAN Zone Marker Span Query Resp
Page 708 and 709: The preamplifier gain is set by usi
Page 710 and 711: Hewlett-Packard and is available fo
Page 712 and 713: INVALID KEYLBL: _ - - Indicates tha
Page 714 and 715: OVEN COLD Indicates that the spectr
Page 716 and 717: Trace A is not available Indicates
Page 718 and 719: RS-232 and Parallel Option 043 What
Page 720 and 721: Person0 computer Analyzer TxD 2 > >
Page 724 and 725: Setting the Spectrum Analyzer Baud
Page 726 and 727: B Bl, 5-9 B2, 5-9 B3, 5-9 B4, 5-9 b
Page 728 and 729: demodulation, 5-128 DET, 5-129 dete
Page 730 and 731: FUNCDEF command avoiding problems,
Page 732 and 733: limits failed, 5-272 mirror limit l
Page 734 and 735: NRL, 5-384 NTSC triggering, 5-575 n
Page 736 and 737: PWRUPTIME, 5-456 It Rl, 5-10 R2, 5-
Page 738 and 739: marker step size, 5-358 STOP FREQ s
Page 740: window next, 5-592 window off, 5-59
show all

HP 8590 E & L Series Spectrum Analyzers and HP 8591C Cable TV ...

Create successful ePaper yourself

Delete template?

Save as template?