P12x/EN T/Eb6 - Schneider - error

More documents

Recommendations

Info

P12x/EN AP/Eb6Page 12/78Application GuideMiCOM P120/P121/P122/P1233. TRANSFORMER INRUSH CURRENT (P122 & P123 only)The inrush blocking function assumes stability protection during transformer energisingbased on harmonic 2 presence.In applications where the sensitivity of overcurrent thresholds need to be set below theprospective peak inrush current, the inrush block function can be used to block theovercurrent, earth fault and negative sequence overcurrent stages. During transformerinrush conditions, the second harmonic component of the inrush current may be as high as70%. In practice, the second harmonic level may not be the same for all phases duringinrush and therefore the relay will provide an Inrush Blocking signal for any phase above theset threshold. In general, a setting of 15% to 20% for the Inrush harmonic 2 ratio can beapplied in most cases taking care that setting it too high, inrush blocking may not operate forlow levels of second harmonic current which may result in the O/C element tripping duringtransformer energization. Similarly applying a too low a setting, inrush blocking may preventtripping during some internal transformer faults with significant second harmonic current.3.1 OverviewInrush Blocking function operates by measuring ratio of second to fundamental harmoniccurrent. It could be used as “blocking logic” of I >, I >>, I >>>, I0 >, I0 >>, I0 >>>, Ie >>>>,I2 >, I2 >> or I2 >>> in case the harmonic 2 ratio is higher than the settable threshold.Indeed, inrush blocking functions will reset selected protection function starting.The minimum duration of overcurrent threshold inhibition (tReset) can be also set. This valuedepends on the transformer power transient inrush duration: between 0.1 second (for a100kVA transformer) to 1.0 second (for a large unit). It is used to avoid any maloperationduring a fixed duration in case of too sensitive setting.3.2 OperationFor each of the three phases currents (IA, IB, IC), the harmonic restraint function comparesthe ratio of harmonic 2 to fundamental with the setting ratio (adjustable from Harmonic 2 /Fundamental = 10 % up to 35 % step 1%).Minimum fundamental current value required for operation of Inrush Blocking function. Thereis 0.2In, and there is no upper limit to disable this feature. However, in transformerprotection, the high set overcurrent stage shall not be controlled by this Inrush Blockingfeature; this enables detection of all high current faults without inrush blocking.Inrush Blocking feature will block selected protection stages, any time inrush conditionsoccurs on the line (Ratio of 2nd Harmonics measured > Inrush H2 settings ratio), and will beat least active during tReset.
Application GuideP12x/EN AP/Eb6MiCOM P120/P121/P122/P123 Page 13/78Operating Inrush current is settable from 10% to 35% of fundamental current.tReset timer defines the minimum duration of overcurrent threshold inhibition (0-2s, settable).This timer starts as soon as operating inrush current threshold picks up:−−If inrush condition duration is smaller than tReset setting value, selected overcurrentfunction will remain inhibited during tReset.If inrush condition duration is longer than tReset setting value, selected overcurrentfunction will be inhibited as long as inrush condition remains valid.Under inrush condition, the following selectable protection stages will be blocked:
Page 1:
MiCOMP120/P121/P122/P123Overcurrent
Page 4 and 5:
P12x/EN T/Eb6Page 2/2Technical Guid
Page 7 and 8:
Pxxx/EN SS/G11Safety Section Page 1
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15:
IntroductionP12x/EN IT/Eb6MiCOM P12
Page 18:
P12x/EN IT/Eb6Page 2/8IntroductionM
Page 22 and 23:
P12x/EN IT/Eb6Page 6/8IntroductionM
Page 25:
Handling, Installation and Case Dim
Page 28 and 29:
P12x/EN IN/Eb6Page 2/10Handling, In
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
P12x/EN IN/Eb6Page 10/10Handling, I
Page 39 and 40:
User GuideP12x/EN FT/Eb6MiCOM P120/
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101:
Menu Content TablesP12x/EN HI/Eb6Mi
Page 104 and 105:
P12x/EN HI/Eb6Page 2/22Menu Content
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
P12x/EN HI/Eb6Page 10/22Menu Conten
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
P12x/EN HI/Eb6Menu Content TablesPa
Page 127 and 128:
Technical DataP12x/EN TD/Eb6MiCOM P
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174: Technical DataP12x/EN TD/Eb6MiCOM P
Page 175 and 176: Technical DataP12x/EN TD/Eb6MiCOM P
Page 177: Getting StartedP12x/EN GS/Eb6MiCOM
Page 180 and 181: P12x/EN GS/Eb6Page 2/32Getting Star
Page 188 and 189: P12x/EN GS/Eb6Page 10/32Getting Sta
Page 213 and 214: Application GuideP12x/EN AP/Eb6MiCO
Page 223: Application GuideP12x/EN AP/Eb6MiCO
Page 275 and 276:
Application GuideP12x/EN AP/Eb6MiCO
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
CommunicationsP12x/EN CT/Eb6MiCOM P
Page 293 and 294:
Page 295 and 296:
CommunicationsP12x/EN CT/Eb6MODBUS
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
Page 345 and 346:
Page 347 and 348:
Page 349 and 350:
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
CommunicationsP12x/EN CT/Eb6COURIER
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
Page 367 and 368:
Page 369 and 370:
Communications P12x/EN CT/Eb6COURIE
Page 371 and 372:
Page 373 and 374:
Page 375 and 376:
Page 377 and 378:
Page 379 and 380:
Page 381 and 382:
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Page 391 and 392:
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
Page 413 and 414:
Page 415 and 416:
Page 417 and 418:
Page 419 and 420:
Page 421 and 422:
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
Page 429 and 430:
Page 431 and 432:
Page 433 and 434:
Page 435 and 436:
Page 437 and 438:
Page 439 and 440:
Page 441 and 442:
Page 443 and 444:
Page 445 and 446:
Page 447 and 448:
Page 449 and 450:
Page 451 and 452:
Page 453 and 454:
Page 455 and 456:
Page 457 and 458:
Page 459 and 460:
Page 461 and 462:
Page 463 and 464:
Page 465 and 466:
Page 467 and 468:
Page 469 and 470:
Page 471 and 472:
Page 473 and 474:
Page 475 and 476:
CommunicationsP12x/EN CT/Eb6IEC 608
Page 477 and 478:
Page 479 and 480:
Page 481 and 482:
Communications P12x/EN CT/Eb6IEC 60
Page 483 and 484:
Page 485 and 486:
Page 487 and 488:
Page 489 and 490:
Page 491 and 492:
Page 493 and 494:
Page 495:
Page 498 and 499:
P12x/EN CT/Eb6DNP 3.0 DatabasePage
Page 500 and 501:
Page 502 and 503:
Page 504 and 505:
Page 506 and 507:
Page 508 and 509:
Page 510 and 511:
Page 513 and 514:
Commissioning and MaintenanceP12x/E
Page 515 and 516:
Page 517 and 518:
Page 519 and 520:
Page 521 and 522:
Page 523 and 524:
Page 525 and 526:
Page 527 and 528:
Page 529 and 530:
Page 531:
Connection DiagramsP12x/EN CO/Eb6Mi
Page 534 and 535:
P12x/EN CO/Eb6Page 2/2Connection Di
Page 537 and 538:
Commissioning Test & Record SheetsP
Page 539 and 540:
Page 541 and 542:
Page 543 and 544:
Page 545 and 546:
Page 547 and 548:
Page 549 and 550:
Page 551 and 552:
Page 553 and 554:
Page 555 and 556:
Page 557 and 558:
Page 559 and 560:
Page 561 and 562:
Page 563 and 564:
Page 565 and 566:
Page 567 and 568:
Page 569 and 570:
Page 571 and 572:
Page 573 and 574:
Page 575 and 576:
Page 577 and 578:
Page 579:
Hardware/Software VersionHistory an
Page 582 and 583:
P12x/EN VC/Eb6Page 2/34Hardware/Sof
Page 584 and 585:
Page 586 and 587:
Page 588 and 589:
Page 590 and 591:
P12x/EN VC/Eb6Page 10/34Hardware/So
Page 592 and 593:
Page 594 and 595:
Page 596 and 597:
Page 598 and 599:
Page 600 and 601:
Page 602 and 603:
Page 604 and 605:
Page 606 and 607:
Page 608 and 609:
Page 610 and 611:
Page 612 and 613:
Page 614 and 615:
Page 617 and 618:
Update DocumentationP12x/EN AD/Eb6M
Page 619 and 620:
Page 621 and 622:
Page 623 and 624:
Page 625 and 626:
Page 628:
Customer Care Centrehttp://www.schn
show all

P12x/EN T/Eb6 - Schneider - error

Create successful ePaper yourself

Delete template?

Save as template?