P12x/EN T/Eb6 - Schneider - error

More documents

Recommendations

Info

P12x/EN AP/Eb6Page 46/78Application GuideMiCOM P120/P121/P122/P12321. BROKEN CONDUCTOR DETECTION (P122 & P123 ONLY)Most of the faults that affect a power system occur between one phase and the earth orbetween two phases and the earth. These faults are shunt faults and are caused by lightningdischarges and other overvoltages generating flashovers. They may also arise from birds onoverhead lines or mechanical damage on underground cables, etc.Such faults lead the current to increase appreciably and therefore they can easily bedetected in most applications. Open circuit faults are a different type of faults that canhappen in electrical networks. These faults can be caused by broken conductors, blownfuses or misoperation of a pole of a circuit-breaker.Series faults will not lead to an increase in phase current and therefore they can not beeasily detected by common overcurrent relays. However, this type of faults produce anunbalance that creates negative phase sequence current, which can be detected.The use of negative phase sequence overcurrent is then recommended to detect such faultyconditions. However, on lightly loaded lines, the value of the negative sequence currentcaused by a faulty condition may be very close to, or even inferior, to the full load steadystate unbalance generated by CT errors, load unbalance, etc. As a consequence, a negativesequence protection element would not work for low level of loads.As a solution, MiCOM P122 and P123 have a protection element that measures the ratiobetween the negative and the positive phase sequence current (I2/I1). Using this ratioinstead of the measure of I2 only, the relay will be able to detect a faulty conditionindependently on the level of load on the network, since the ratio is approximately constantwith variations in load current. It is then possible to get a more sensitive setting.NOTE:the Broken conductor function is inhibited if the current value flowingin each one of the three phases is inferior to 10% of the nominalcurrent.Setting GuidelinesOn single point earthed power systems, there is a low zero sequence current flow and theratio I2/I1 that flows is close to100%. On multiple earthed power systems, (assuming that theimpedances in each sequence network are equals), the ratio I2/I1 will be equal to 50%.It is possible to calculate the ratio of I2/I1 corresponding to various system impedances,according to the following equations:E g (Z 2 +Z 0 )I 1F =Z 1 Z 2 +Z 1 Z 0 +Z 2 Z 0I 2F =Where:–E g Z 0Z 1 Z 2 +Z 1 Z 0 +Z 2 Z 0E g = System VoltageZ 0 = Zero sequence impedanceZ 1 = Positive sequence impedanceZ 2 = Negative sequence impedanceTherefore:I 2F Z 0I=1F Z 0 +Z 2As a consequence, for an open circuit in a particular part of the system, I2/I1 can bedetermined from the ratio between the zero sequence and the negative sequenceimpedance. It must be noted however, that this ratio may vary depending on the location ofthe fault. It is therefore desirable to apply a setting that is as sensitive as possible.Practically, the levels of standing negative phase sequence current present on the systemguide the choice of this minimum setting. A system study, or the use of measurement data ofthe relay during commissioning stage are two ways to determine this minimum setting. If thelatter method is chosen, it is important to take measurements during maximum loadconditions, to be sure that all single phase loads are taken into account.
Application GuideP12x/EN AP/Eb6MiCOM P120/P121/P122/P123 Page 47/78A time delay (tBC) is necessary to ensure co-ordination with other protective devices.21.1 Example of SettingThe following information comes from a the relay commissioning report;I full load = 500AI 2 = 50AThen:I 2 /I 1 = 50/500 = 0.1To tolerate some margin and load variations, it is typical to set this value at 200% above thisvalue: Therefore, RATIO I2/I1 = 20%Set tBC at 60s to allow short circuits to be cleared by time delayed protections.
Page 1:
MiCOMP120/P121/P122/P123Overcurrent
Page 4 and 5:
P12x/EN T/Eb6Page 2/2Technical Guid
Page 7 and 8:
Pxxx/EN SS/G11Safety Section Page 1
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15:
IntroductionP12x/EN IT/Eb6MiCOM P12
Page 18:
P12x/EN IT/Eb6Page 2/8IntroductionM
Page 22 and 23:
P12x/EN IT/Eb6Page 6/8IntroductionM
Page 25:
Handling, Installation and Case Dim
Page 28 and 29:
P12x/EN IN/Eb6Page 2/10Handling, In
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
P12x/EN IN/Eb6Page 10/10Handling, I
Page 39 and 40:
User GuideP12x/EN FT/Eb6MiCOM P120/
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101:
Menu Content TablesP12x/EN HI/Eb6Mi
Page 104 and 105:
P12x/EN HI/Eb6Page 2/22Menu Content
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
P12x/EN HI/Eb6Page 10/22Menu Conten
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
P12x/EN HI/Eb6Menu Content TablesPa
Page 127 and 128:
Technical DataP12x/EN TD/Eb6MiCOM P
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177:
Getting StartedP12x/EN GS/Eb6MiCOM
Page 180 and 181:
P12x/EN GS/Eb6Page 2/32Getting Star
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
P12x/EN GS/Eb6Page 10/32Getting Sta
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209: P12x/EN GS/Eb6Page 30/32Getting Sta
Page 210 and 211: P12x/EN GS/Eb6Page 32/32Getting Sta
Page 213 and 214: Application GuideP12x/EN AP/Eb6MiCO
Page 257: Application GuideP12x/EN AP/Eb6MiCO
Page 291 and 292: CommunicationsP12x/EN CT/Eb6MiCOM P
Page 293 and 294: CommunicationsP12x/EN CT/Eb6MiCOM P
Page 295 and 296: CommunicationsP12x/EN CT/Eb6MODBUS
Page 309 and 310:
CommunicationsP12x/EN CT/Eb6MODBUS
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
Page 345 and 346:
Page 347 and 348:
Page 349 and 350:
Page 351 and 352:
Page 353 and 354:
CommunicationsP12x/EN CT/Eb6MiCOM P
Page 355 and 356:
CommunicationsP12x/EN CT/Eb6COURIER
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
Page 367 and 368:
Page 369 and 370:
Communications P12x/EN CT/Eb6COURIE
Page 371 and 372:
Page 373 and 374:
Page 375 and 376:
Page 377 and 378:
Page 379 and 380:
Page 381 and 382:
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Page 389 and 390:
Page 391 and 392:
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
Page 413 and 414:
Page 415 and 416:
Page 417 and 418:
Page 419 and 420:
Page 421 and 422:
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
Page 429 and 430:
Page 431 and 432:
Page 433 and 434:
Page 435 and 436:
Page 437 and 438:
Page 439 and 440:
Page 441 and 442:
Page 443 and 444:
Page 445 and 446:
Page 447 and 448:
Page 449 and 450:
Page 451 and 452:
Page 453 and 454:
Page 455 and 456:
Page 457 and 458:
Page 459 and 460:
Page 461 and 462:
Page 463 and 464:
Page 465 and 466:
Page 467 and 468:
Page 469 and 470:
Page 471 and 472:
Page 473 and 474:
Page 475 and 476:
CommunicationsP12x/EN CT/Eb6IEC 608
Page 477 and 478:
Page 479 and 480:
Page 481 and 482:
Communications P12x/EN CT/Eb6IEC 60
Page 483 and 484:
Page 485 and 486:
Page 487 and 488:
Page 489 and 490:
Page 491 and 492:
Page 493 and 494:
Page 495:
Page 498 and 499:
P12x/EN CT/Eb6DNP 3.0 DatabasePage
Page 500 and 501:
Page 502 and 503:
Page 504 and 505:
Page 506 and 507:
Page 508 and 509:
Page 510 and 511:
Page 513 and 514:
Commissioning and MaintenanceP12x/E
Page 515 and 516:
Page 517 and 518:
Page 519 and 520:
Page 521 and 522:
Page 523 and 524:
Page 525 and 526:
Page 527 and 528:
Page 529 and 530:
Page 531:
Connection DiagramsP12x/EN CO/Eb6Mi
Page 534 and 535:
P12x/EN CO/Eb6Page 2/2Connection Di
Page 537 and 538:
Commissioning Test & Record SheetsP
Page 539 and 540:
Page 541 and 542:
Page 543 and 544:
Page 545 and 546:
Page 547 and 548:
Page 549 and 550:
Page 551 and 552:
Page 553 and 554:
Page 555 and 556:
Page 557 and 558:
Page 559 and 560:
Page 561 and 562:
Page 563 and 564:
Page 565 and 566:
Page 567 and 568:
Page 569 and 570:
Page 571 and 572:
Page 573 and 574:
Page 575 and 576:
Page 577 and 578:
Page 579:
Hardware/Software VersionHistory an
Page 582 and 583:
P12x/EN VC/Eb6Page 2/34Hardware/Sof
Page 584 and 585:
Page 586 and 587:
Page 588 and 589:
Page 590 and 591:
P12x/EN VC/Eb6Page 10/34Hardware/So
Page 592 and 593:
Page 594 and 595:
Page 596 and 597:
Page 598 and 599:
Page 600 and 601:
Page 602 and 603:
Page 604 and 605:
Page 606 and 607:
Page 608 and 609:
Page 610 and 611:
Page 612 and 613:
Page 614 and 615:
Page 617 and 618:
Update DocumentationP12x/EN AD/Eb6M
Page 619 and 620:
Page 621 and 622:
Page 623 and 624:
Page 625 and 626:
Page 628:
Customer Care Centrehttp://www.schn
show all

P12x/EN T/Eb6 - Schneider - error

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?